Fluke 717 Data sheet

Technical Data

Fluke 718 Pressure Calibrator

The complete solution to pressure calibration

The Fluke 718 pressure calibrator family (4 models)

provide a total pressure calibration solution for

transmitters, gauges and switches. This compact

pressure calibration solution is about a third of the

kilogram (two pounds). The unique, easy to clean

pump from fl uids and provides the ability to service

the pump without disassembly.

Pressure Source and Milliamp Measurement to

Integrated pump is easily cleaned when

– reduces cost of ownership and repairs

– service the pump in the fi eld

Error % calculation for quicker pass/fail decision

making in the fi eld

Best in class mA accuracy of 0.015 % for better

measurement confi dence and workload coverage

Min/Max/Hold to capture changing measurements

Switch test feature for quicker and more accurate

pressure switch testing

New 1 and 300 PSI pressure ranges mean fewer

1, 30, 100 & 300 PSI ranges now available

Maximum voltage:

30 volts: Non-operating

Temperature:

-40 °C to 60 °C

Operating temperature:

-10 °C to 55° C

Relative humidity:

95 % (10 °C to 30 °C); 75 % (30 °C to 40 °C);

Operating altitude:

3,000 m max

1 m drop test

Vibration:

Random, 2 g, 5 Hz – 500 Hz

CSA C22.2 No. 1010.1: 1992

EMC:

EN50082-1: 1992 and EN55022: 1994 Class B

201 mm x 98 mm x 52 mm

216 mm x 94 mm x 66 mm

Power:

9V battery ANSI/NEDA 1604A or IEC 6LR619V alkaline; two

batteries in 718

Battery Life:

4 to 20 hours typical, depending on functions used

Warranty:

Three years (one year on pressure pump in Fluke 718)

Display:

LCD, 5 digit pressure and current simultaneous

Accuracy:

0.05 %

Note:

For use with non-corrosive gasses

2 Fluke Pressure Calibrators

Functional Pressure Specifi cations

Model

Range

Resolution

Over Pressure

Functions

718 1G

-1 PSI to +1 PSI, -68.9 mbar to

0.0001 psi, 0.001 mbar

Zero, Min, Max, Hold, Damp

718 30G

-12 PSI to 30 PSI, (-850 mbar to

0.001 psi, 0.1 mbar

Zero, Min, Max, Hold, Damp

718 100G

-12 PSI to 100 PSI, (-850 mbar to

0.01 psi, 1 mbar

Zero, Min, Max, Hold, Damp

718 300G

-12 PSI to 300 PSI, (-850 mbar to

0.01 psi, 1 mbar

Zero, Min, Max, Hold, Damp

717 1G

-1 PSI to 1 PSI, (-68.9 mbar to

0.001 psi, 0.001 mbar

Zero, Min, Max, Hold, Damp

717 30G

-12 PSI to 30 PSI, (-850 mbar to

0.001 psi, 0.1 mbar

Zero, Min, Max, Hold, Damp

717 100G

-12 PSI to 100 PSI, (-850 mbar to

0.01 psi, 1 mbar

Zero, Min, Max, Hold, Damp

717 300G

-12 PSI to 300 PSI, (-850 mbar to

0.01 psi, 1 mbar

Zero, Min, Max, Hold, Damp

717 500G

0 PSI to 500 PSI, (0 mbar to

34.47 bar, 0 to 3447.4 kPa )

0.01 psi, 1 mbar

Zero, Min, Max, Hold, Damp

717 1000G

0 PSI to 1000 PSI, (0 mbar to

0.1 psi, 1 mbar

Zero, Min, Max, Hold, Damp

717 1500G

0 PSI to 1500 PSI, (0 mbar to

0.1 psi, 0.01 bar

Zero, Min, Max, Hold, Damp

717 3000G

0 PSI to 3000 PSI, (0 mbar to

0.1 psi, 0.01 bar

Zero, Min, Max, Hold, Damp

717 5000G

0 PSI to 5000 PSI, (0 mbar to

344.74 bar, 0 to 34474 kPa)

0.1 psi, 0.01 bar

Zero, Min, Max, Hold, Damp

Functional Specifi cations

The New 718 Calibrator Pump

The new Fluke 718 is a uniquely protected pneu-

matic pressure calibrator and pump. The new pump

pass through the pump for calibration but inhibits

fl uids from entering the pump and causing damage.

These two check valves allow the bi-directional

fl ow of air into or out of the 718. Even after drain-

ing the process fl uid from the calibration port of the

may often still be lurking behind. In the event these

fl uids enter the 718 pump cavities, the new pump

Pump valve assembly cleaning instructions

retention caps located in the oval shaped opening

the spring and o-ring assembly.

residue.

retention caps with IPA and inspect the o-rings

needed.

They should be approximately 8.6 mm long in the

relaxed state. If

they are shorter

than this, they

may not allow

the o-ring to

Replace if

needed.

parts have

been cleaned

reinstall the o-

ring and spring

the valve body.

retention caps

tighten the cap.

the unit to at least 50 % its rated pressure.

The Calibrator is now ready for use.

Cleaning the fl uid trap in the Fluke-718

Calibrator is quick, easy and only requires a

slotted screwdriver and cotton swab

3 Fluke Pressure Calibrators

Fluke 718 series via using 700 Series Pressure Modules

Range:

2

0 to 10,000 psi, 2.5 mbar to

Resolution:

Per pressure module specs

Accuracy:

To 0.025 % of full span, per pressure module specs

Functions:

Note: media compatibility per pressure module specs

Fluke 718 series via built in pump

Range:

-12 PSI or -850 mbar to full scale, Supported Pressure Units; psi, in H

2

0 (4 °C), in

2

0 (20 °C), cm H

2

0 (4 °C), cm H

2

0 (20 °C), bar, mbar, kPa, inHg, mmHg, kg/cm

Loop Power:

Range:

Accuracy:

Note: Drive; 20 mA into 1000

for battery > 6.8V; 700

for battery 5.8 to 6.8 V

Measure Accuracy:

Range:

0 mA to 24 mA

Resolution:

0.001 mA

Accuracy:

0.015 % + 1 count

Fluke 717 Series via pressure module connector using optional Pressure Modules

Range:

0 to 10,000 PSI, 2.5 mbar to

Resolution:

Per pressure module specs

Accuracy:

0.025 % of full span, per pressure module specs

Functions:

Note: Media compatibility per pressure module specs

Fluke Corporation

PO Box 9090, Everett, WA USA 98206

Fluke Europe B.V.

PO Box 1186, 5602 BD

Eindhoven, The Netherlands

For more information call:

In the U.S.A. [phone] or

Fax [phone]

In Europe/M-East/Africa (31 40) 2 675 200 or

Fax [phone]

In Canada (800) 36-FLUKE or

Fax [phone]

From other countries [phone] or

Fax [phone]

Web access: http://www.fl uke.com

Printed in U.S.A. 2/2006 2577864 D-EN-N Rev A

Keeping your world

up and running.

For additional detail on the 718, see the application note "Pressure calibration with the 718."

Literature code: 2577485 at

www.fl uke.com/library