FLUKE 705, 715, 787 User Manual

Fluke 705

● A large display and simple, pushbutton

interface for ease of use.

● Simultaneous mA and % readout for

quick, easy, interpretation of readings.

● mA accuracy of 0.02%.

● Push button 25% steps for fast, easy

linearity checks. Save time over traditional knob type controls.

● "Span Check" for fast confirmation of

zero and span.

● Selectable slow ramp, fast ramp, and

step to provide smooth outputs for valve slewing and loop functional tests.

● 24 volt internal loop supply, so you can

power and read a transmitter at the same time without carrying a DMM.

● 0 - 20 mA or 4 - 20 mA default start up

modes.

715 Volt/mA Calibrator

● Measure loop current (0-20 mA,

4-20 mA) signals with 0.015% accuracy and 0.001 mA resolution

● Measure voltage output process signals

from PLCs, transmitters

● Source or simulate 24 mA loop current

● Source voltage to 100 mV or 10V

● 24V loop supply with simultaneous

current measurement

Fluke 787

● DMM and loop calibrator in one tool

● Precision 1000V, 440 mA digital

multimeter

● DC current source/loop calibrator

● Clear LCD with backlight; 4000 counts

(30 000 counts for DC current)

● Externally accessible battery for easy

battery changes

● 1000V overload protection on V, ohms,

frequency

● Meets 1000 volt EN61010-1 CAT III

standards

● Min/Max/Average/Hold/Relative modes

705 715 787

0-28 V DC 0-100 mV 0-10 V 1 mV 10 µV 1 mV

0.025% Rdg + 1 LSD 0.02% Rdg + 2 LSD 0.1% Rgd + 1 LSD (VDC)

0-24 mA 0-24 mA 0-1 A 0-30 mA

0.001 mA 0.001 mA 1 mA 0.001 mA

0.02% + 2 LSD 0.015% 0.2%+2 LSD 0.05%+2 LSD

0.025% Rdg + 2 LSD 0.015% + 2 LSD 1000 Ω @ 24 mA 1000 Ω @ 24 mA 500 Ω @ 24 mA

24 V 24 V

Features

Accessories and Ordering Information

Included Accessories:

FLUKE 705: C10 Protective Yellow Holster, TL75 Test Leads, AC70 Test Clips, Instruction Sheet (14 languages). FLUKE 715: C81Y Protective Yellow Holster with Flex-Stand, Test Leads and Alligator Clips, Single 9V alkaline battery, Instruction Sheet (14 languages). FLUKE 787: C81Y Protective Yellow Holster with Flex-Stand, TL75 SafetyDesigned Test Lead Set plus AC70A Alligator Clips, one 9V alkaline battery, Users Manual.

Ordering information:

FLUKE 705 Loop Calibrator FLUKE 715 Volt/mA Calibrator FLUKE 787 ProcessMeter

Pub_ID: 10034-eng Rev. 02

will over-range to 24 mA

Functions

Voltage measurement

Range 0-1000 V AC or DC Resolution 0.1 mV to 1.0 V Accuracy

Current measurement

Range Resolution Accuracy

Current sourcing

Range 0-20 mA or 4-20 mA

0-20 mA or 4-20 mA10-20 mA or 4-20 mA

Accuracy 0.05% of span Drive capability 500 Ω @ 24 mA Loop power while

measuring mA N/A Voltage sourcing N/A 0-100 mV or 0-10 V N/A Resistance

measurement N/A N/A to 40 MΩ, 0.2% + 1 LSD Frequency N /A N/A to 19.999 kHz,

0.005% + 1 LSD

Diode test N/A N/A 2.4 V shows

diode voltage drop

Continuity N/A N/A Beeps for

resistance <100 ohms

Display current and % of span Yes mA or % Yes

Auto step, auto ramp Yes No Yes Span Check Yes No No Battery life 18 hours typical, 18 hours typical, 50 hours typical,

at 12 mA at 12 mA 12 hours sourcing 12 mA

Loop Calibrators

Low Cost Calibrator Muscle