Page 1
2000ACC
Accessory Kit
Instructions
Contact Fluke
Fluke Corporation operates worldwide. For local contact
information, go to our website: www.fluke.com
To register your product, or to view, print, or download the
latest manual or manual supplement, go to our website:
www.fluke.com/productinfo
Fluke Corporation
P.O. Box 9090
Everett WA 98206-9090
U.S.A.
+1-425-446-5500 fluke-info@fluke.com
.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
Safety Information
A Warning identifies hazardous conditions and procedures
that are dangerous to the user. A Caution identifies
conditions and procedures that can cause damage to the
Product or the equipment under test.
Warning
To prevent possible electrical shock, fire, or
personal injury:
Read all safety information before you use the
Product.
Use the Product only as specified, or the protection
supplied by the Product can be compromised.
Carefully read all instructions.
.
PN 5416998 (English)
1/2023
©2023 Fluke Corporation. All rights reserved. Specifications are
subject to change without notice. All Product names are
trademarks of their respective companies.
Page 2
Comply with local and national safety codes. Use
personal protective equipment (approved rubber
gloves, face protection, and flame-resistant
clothes) to prevent shock and arc blast injury where
hazardous live conductors are exposed.
Use Product-approved measurement category
(CAT), voltage, and amperage rated accessories
(probes, test leads, and adapters) for all
measurements.
Do not touch voltages >30 V ac rms, 42 V ac peak,
or 60 V dc.
Do not use the Product around explosive gas,
vapor, or in damp or wet environments.
Do not exceed the Measurement Category (CAT)
rating of the lowest rated individual component of a
Product, probe, or accessory.
Do not use test leads if they are damaged. Examine
the test leads for damaged insulation, exposed
metal, or if the wear indicator (if present) shows.
Check test lead continuity.
Keep fingers behind the finger guards on the
probes.
Do not use in CAT III or CAT IV environments
without the protective cap (if included with the
Product) installed on test probe. The protective cap
decreases the exposed probe metal to <4 mm. This
decreases the possibility of arc flash from short
circuits.
Do not use a shrouded banana jack accessory such
as an alligator clip with an unshrouded 4 mm
banana probe tip terminal in a hazardous electrical
installation. Due to the lack of a shroud, the probe
tip connector does not provide suitable insulation
to accessible parts with this type of assembly.
2
Page 3
Symbols
The table below lists the symbols that can be used on the
Product or in this document.
Symbol Description
Consult user documentation.
WARNING. RISK OF DANGER.
WARNING. HAZARDOUS VOLTAGE. Risk of
electric shock.
Double insulated
Measurement Category II is applicable to test
and measuring circuits connected directly to
utilization points (socket outlets and similar
points) of the low-voltage MAINS installation.
Measurement Category III is applicable to test
and measuring circuits connected to the
distribution part of the building’s low-voltage
MAINS installation.
Measurement Category IV is applicable to test
and measuring circuits connected at the
source of the building’s low-voltage MAINS
installation.
Conforms to European Union directives.
Maintenance
Clean with a soft towel moistened with water and mild
detergent. DO NOT IMMERSE in liquid.
Electrical Specifications
Refer to markings on probe assembly and accessories for
voltage and current specifications. If no CAT rating is
marked, by default ratings are 30 V ac rms, 42 V ac peak or
60 V dc, 8 A. Probe tips with >19 mm (0.75 in) exposed metal
are rated 30Vac, 60Vdc, ≤8A.
Environmental Specifications
Te m p e r a t u r e -20 °C to 50 °C (-4 °F to 122 °F)
Relative humidity
Altitude 2000 m
Safety IEC 61010-031: Pollution Degree 2
0 % to 95 %, 0 °C to 35 °C
(32 °F to 95 °F)
3
Page 4
LIMITED WARRANTY
This Fluke product will be free from defects in material and
workmanship for 1 year from the date of purchase. This
warranty does not cover fuses, disposable batteries, or
damage from accident, neglect, misuse, alteration,
contamination, or abnormal conditions of operation or
handling. Resellers are not authorized to extend any other
warranty on Fluke’s behalf. To obtain service during the
warranty period, contact your nearest Fluke authorized
service center to obtain return authorization information,
then send the product to that Service Center with a
description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM
ANY CAUSE OR THEORY. Since some states or countries do
not allow the exclusion or limitation of an implied warranty or
of incidental or consequential damages, this limitation of
liability may not apply to you.
11/99
4
Loading...