Fluke 120, 190B, 190C Technical Data

ScopeMeter®190C/190B Series

C

E

R

T

I

F

I

E

D

T

O

M

E

E

T

I

S

O

9

0

0

1



Q

U

A

L

I

T

Y

M

A

N

A

G

E

M

E

N

T

S

Y

S

T

E

M

R

LISTED

®

and ScopeMeter

120 Series

Technical Data

ScopeMeter 190C and 190B
Series: Speed, performance
and analysis power

For demanding applications, the
ScopeMeter 190C and 190B Series
high-performance oscilloscopes
offer specifications usually found on
top-end bench instruments. With
up to 200 MHz bandwidth,

2.5 GS/s real time sampling and a
deep memory of 27,500 points per
input they’re ideal for engineers
who need the full capabilities of a
high-performance scope in a hand­held, battery powered instrument.

Dual input - 200, 100 or

•

60 MHz bandwidth

Now expanded with 3K memory and
FFT Frequency Spectrum Analysis

Up to 2.5 GS/s real time

•

sampling per input
High Waveform Resolution of

•

3000 datapoints per channel
Frequency Spectrum using FFT

•

analysis (190C)
Connect-and-View™automatic

•

triggering, a full range of man­ual trigger modes plus external
triggering

Digital Persistence for analyzing

•

complex, dynamic signals like
on an analog oscilloscope (190C)

Fast display update rate for

•

seeing dynamic behavior
instantaneously

Automatic capture and replay of

•

100 screens
27,500 points and more per

•

input record length using
ScopeRecord

1,000 V CAT II and 600 V CAT

•

III safety certified
Up to 1,000 V independently

•

floating isolated inputs
Four hours rechargeable

•

NiMH battery pack

™

mode

ScopeMeter 120 Series:
Three-in-one simplicity

The compact ScopeMeter 120 Series
is the rugged solution for industrial
troubleshooting and installation
applications. It’s a truly integrated
test tool, with oscilloscope, multi­meter and “paperless” recorder in
one affordable, easy-to-use instru­ment. Find fast answers to problems
in machinery, instrumentation,
control and power systems.

A dual input 40 MHz or 20 MHz

•

digital oscilloscope
Two 5,000 counts true-rms

•

digital multimeters
Cursor measurements (Fluke 124)

•

A dual input TrendPlot recorder

•

Connect-and-View trigger

•

simplicity for hands-off operation
Shielded test leads for oscillo-

•

scope, resistance, continuity
and capacitance measurements

Hz prob

idth, VPS40 1

e included standard

24

ull bandw

F

•

40 M

ith Fluke 1

w
Up to seven hours batter

•

operation
600 V CAT III safety certified

•

Optically isolated RS-232

•

interface
Rugged, compact case

•

0:1

y

Technical Specifications 190C and 190B Series

Oscilloscope Mode

Vertical Deflection

Fluke 199C Fluke 196C

99B Fluke 196B Fluke 192B

idth 200 MHz 100 MHz 60 MHz

Bandw
Rise time

Bandwidth limiter: User selectable: 10 kHz, 20 MHz
or off
Number of inputs: 2 plus external trigger. All inputs
isolated from each other and ground.

Input coupling: AC or DC, with ground level indicator
Input sensitivity: 2 mV/div to 100 V/div (Fluke 190C

Series); 5 mV/div to 100 V/div (Fluke 190B Series)
Normal/Invert: On both input channels; switched
separately

Variable attenuator: Variable gain on input channel A
Input voltage: 1000 V CAT II, 600 V CAT III rated -

See “general specifications” for further details.

Vertical resolution: 8 bit
Accuracy: ± (1.5% of reading + 0.04 x range/div)
Input impedance: 1 MΩ ± 1% // 15 pF ± 2 pF

Horizontal

Maximum 2.5 GS/s 1 GS/s 500 MS/s
real-time
sample rate

Number of 2 2 2
digitizers

Time base 5 ns/div 10 ns/div
range to 5 s/div to 5 s/div

Maximum record length: 3000 points per input in
Scope-mode; 27,500 points per input in
ScopeRecord™ roll mode (5 ms/div to 2 min/div)

Accuracy: ± (0.01 % of reading + 1 pixel)
Glitch capture: 50 nsec (at 5 µsec/div to 1 min/div);

250 nsec (at 2 min/div)

Display and Acquisition

Display 144 mm 144 mm

Display modes Input A, Input B, dual, average, Replay
Persistence Digital Persistence: Persistence

modes

Visible screen width: 12 divisions
Waveform mathematics: A + B, A - B, A * B, all

with user selectable scaling of resultant; A versus B
(X - Y-mode); Frequency Spectrum using FFT analysis
(190C only)
Acquisition modes: Normal, auto, single shot,
ScopeRecord™ roll, glitch capture, waveform
compare, waveform compare with automatic
“Pass / Fail testing” (in 199C and 196C only)

Trigger and Dela

Source: Input A, input B, exter
All input references isolated from each other and
from ground
Modes: Automatic Connect-and­single shot, edge, dela
pulsewidth, dual slope (
only)

Fluke 1

1.7 ns 3.5 ns 5.8 ns

Fluke 199C Fluke 196C
Fluke 199B Fluke 196B Fluke 192B

Fluke 190C Fluke 190B

Full Color LCD Monochrome LCD

short/medium/long/infinite

on / off

y

.

free run,

ycle (190C

ideo, v

y, v

0C only), N

9

1

nal trigger input

™

,

View

ideo line, selectable

-c

Connect-and-View™: Advanced automatic triggering
that recognizes signal patterns, automatically sets up
and continuously adjusts triggering, time base and
amplitude. Automatically displays stable waveforms of
complex and dynamic signals like motor drive and
control signals.
Video triggering: NTSC, PAL, PAL+, SECAM. Includes
field 1, field 2 and line select.
Pulse width triggering: Pulse width qualified by time.
Allows for triggering <t, >t, =t, ≠t, where t is selec­table in minimal steps of 0.01 div. or 50 nsec.
Time delay: One full screen of pre-trigger view or up
to 100 screens (= 1200 divisions) of post-trigger delay
Dual slope triggering: Both rising and falling transi­tions, when crossing the trigger level, initiate an
acquisition (190C only)
N-cycle triggering: Triggers on N-th occurrence of a
trigger event; N to be set in the range 2 to 99 (190C
only)

Automatic Capture of 100 Screens

The instrument ALWAYS memorizes the last 100
screens (no user setup required). When an anomaly
occurs on screen, the REPLAY button can be pressed
to review the full screen sequence over
and over.

Instrument can be set up for triggering on glitches
or intermittent anomalies and will operate in
“baby-sit” mode and will capture 100 events.

Alternatively, the 199C and 196C can be set up in
waveform compare mode to store only matching
(“Pass”) or only non-matching (“Fail”) acquired wave­forms in the replay memory bank for further analysis.
Replay: Manual or continuous replay. Displays the
captured 100 screens as a “live” animation or under
manual control. Each screen has date- and time-stamp.
Replay storage: Up to 2 sets of 100 screens each
can be saved for later recall and analysis

FFT - Frequency Spectrum Analysis
(190C only)

Shows frequency content of oscilloscope waveform
using Fast Fourier Transform

Window: Automatic, Hamming, Hanning or None
Automatic window: Digitally re-samples acquired

waveform to get optimum frequency resolution in FFT
resultant

Vertical scale: Linear / Logarithmic, in volts
Frequency axis: Logarithmic; frequency range auto-

matically set as function of timebase range of oscillo­scope

Waveform Compare and Pass/Fail Testing

Waveform compare: Provides storage and display of a
reference waveform for visual comparison with newly
acquired waveforms. Reference is derived from an
acquired waveform and can be modified in the
ScopeMeter or externally using FlukeView®Software.
Pass/Fail Testing (199C, 196C): In waveform compare
mode, the Color Scopemeter can be set up to store
only matching (“Pass”) or only non-matching (“Fail”)
acquired waveforms in the replay memory bank for
further analysis.

2 Fluke Corporation ScopeMeter 190C/190B Series and ScopeMeter 120 Series

Automatic Scope Measurements

ac rms, Vac+dc, Vpeak max, Vpeak min, Vpeak to

Vdc, V
peak, Aac, Adc, Aac+dc, frequenc
time, power factor, W

idth (pos/neg), dutycycle (pos/neg), temperature °C,

w
temperature

Vpw

idth modulated motordrives and frequency inverters

w

°F, dBV, dBm into 50 Ω and 600 Ω

m ac, Vpwm ac+dc for measurement on pulse

atts, VA, VA reactive, phase, pulse

y (Hz), risetime, fall-

Cursor Measurements

Source: Input A, input B or the Mathematical Result
trace (excl. A vs B curve)
Dual horizontal lines: Voltage at cursor 1 and 2,
voltage b
Dual vertical lines: Time b

etween cursors (in Hz), voltage between markers,

b
risetime w

etween cursors (190C only), watts between cursors

b

190C only)

(

etween cursors

etween cursors, 1/T

ith markers, falltime with markers; Vrms

Single vertical line: Min-Max and Average voltage
at cursor position; frequency and rms-value of individ­ual frequency component in FFT result (190C only)
Zoom: Up to 16x horizontal zoom

Recorder Mode

ScopeRecord-Roll Mode

Dual input waveform storage mode

Source and display: Input A, Input B, Dual
Memory depth: 27,500 points per input. Each point

consists of Min-Max pair
Min-Max values: Min-Max values are measured at
high sample rates ensuring capture and display of
glitches

Time base range 5 ms/div to 1 min/div 2 min/div

Recorded timespan 6 sec to 24 hr 48 hr
Glitch capture 50 ns 250 ns
Sample rate 20 MS/s 4 MS/s
Resolution 200 µsec to 2 sec 4.8 sec

ecording modes:

R

Single sweep, c
Start-on-Trigger, Stop-on-Trigger
Stop-on-Trigger (through external): ScopeRecord
mode can be stopped by an individual trigger event, or
by an interruption of a repetitive trigger signal

Horizontal scale: Time from start, time of day
Zoom: Up to 100x
Memory: Up to 2 dual input ScopeRecord waveforms

can be saved for later recall and analysis

TrendPlot™recording

Single or dual input electronic paperless chart recorder.
Plots, displays and stores meter and scope measure­ments.
Source and display: Input A, Input B or DMM input

ontinuous roll,

Memory depth: 18,000 points recording. Per record
point a minimum, a maximum and an average value,
plus a date and timestamp are recorded.
Ranges: 5 s/div to 30 min/div in normal view mode;
5 min/div to 48 hr/div in view all mode, giving
overview of total record
Recorded timespan: Up to 22 days with a resolution
of 1 minute
Recording mode: Continuous roll for the duration of
the full recordable timespan

Measurement speed: 5 measurements per second
Horizontal scale: Time from start, time of day
Zoom: Up to 64x zoom
Memory: Up to 2 TrendPlot recordings can be saved

for later recall and analysis

Cursor measurements - all recorder modes

Source: Input A, B or DMM input
Dual vertical lines: Min-Max or Average

voltage. Time between cursors
Single vertical line: Min-Max or Average
voltage. Absolute date and time or time from start

Meter Mode

Via 4 mm banana inputs. Fully isolated from scope
inputs and scope ground. The specified accuracy is
valid over the temperature range 18 °C to 28 °C
(65 °F to 82 °F). Add 10 % of specified accuracy for
each degree C below 18 °C or above 28 °C.

Maximum Resolution: 5,000 counts
Voltmeter Ranges: 500 mV, 5 V, 50 V, 500 V, 1,000 V
Accuracy:

Vdc ± (0.5 % + 5 counts)
Vac true rms

15 Hz...60 Hz: ± (1 % + 10 counts)
60 Hz...1 kHz: ± (2.5 % + 15 counts)

Vac+dc true rms

dc...60 Hz: ± (1 % + 10 counts)
60 Hz...1 kHz: ± (2.5 % + 15 counts)

Ohms:
Ranges: 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ
Accuracy: ± (0.6 % + 5 counts)

Other Meter Functions

Continuity: Beeper on < 50 Ω (± 30 Ω)
Diode test: Up to 2.8 V
Amps: Adc, Aac, Aac+dc using an optional current

clamp or shunt. Scaling factors: 0.1 mV/A ... 100 V/A
Temperature (°C, °F): With optional accessories. Scale
factors 1 mV/°C or 1 mV/°F

Input impedance: 1 MΩ ± 1% // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,

relative measurements (Zero reference), TrendPlot
recording

opeMeter 1

Sc

/190B Series and ScopeMeter 120 Series Fluke Corporation 3

0C

9

General Specifications

Memory Save and Recall

Scope memories: 10 memory locations that each can
contain two waveforms plus corresponding setup
Recorder memories: 2 memory locations that each
can contain 100 captured dual input scope screens, or
a dual input ScopeRecord (27,500 Min-Max pairs per
input), or a dual input Trendplot (18,000 min-max
pairs + average values)

Real-Time Clock

Time and date stamp for ScopeRecord, 100 captured
screens and TrendPlots

Mechanical Data

Size: 256 x 169 x 64 mm (10.1 x 6.6 x 2.5 in)
Weight: 2 kg (4.4 lbs)

Case

Design: Rugged, shock proof with integrated
protective holster

Drip and dust proof: IP51 according to IEC529
Shock and Vibration: Shock 30 g, Vibration

(sinusoidal) 3 g according to MIL-PRF-28800F Class 2

Display Bright full-color LCD Bright LCD

Brightness 80 Cd/m

Display size: 115.2 x 86.4 mm (4.54 x 3.4 in.)
Resolution: 320 x 240 pixels
Contrast and brightness: User adjustable,

temperature compensated

Power

Line power: Country specific line voltage
adapter/battery charger included

Battery power: Rechargeable NiMH (installed)
Battery operating time: 4 hours
Battery charging time: 4 hours
Battery power saving functions: Auto power down

with adjustable power down time. On screen battery
status indicator

Fluke 190C Fluke 190B

with backlight, with backlight

2

using power adapter using power adapter

typ. 125 Cd/m2typ.

Safety

Compliance:

N61010-1 (2nd Edition) Pollution degree 2

E

L 3111-1

U

AN/CSA C22.2 No.1010.1

C

NSI/ISA S82.01

A

Input Voltage Ratings

Maximum probe voltage: 1,000 V CAT II/600 V CAT III

(Maximum voltage between 10:1 probe tip (VPS200)
and reference lead)

Floating voltage: 1,000 V CAT II/600 V CAT III

(Maximum voltage between earth ground and any
terminal (signal input or shielding))

Independently isolated inputs:

1,000 V CAT II/600 V CAT III

(Maximum voltage between any terminal of one input
or probe (VPS200) and any other terminal of another
input or probe (VPS200))

Maximum voltage on BNC input directly
(input A or B):

300 V CAT III

Maximum voltage on meter input:

1,000 V CAT II/600 V CAT III

Environmental

Operating temperature: 0 °C to +50 °C
Storage temperature: -20 °C to +60 °C
Humidity:

10 °C to 30 °C: 95% RH non condensing
30 °C to 40 °C: 75% RH non condensing
40 °C to 50 °C: 45% RH non condensing

Maximum operating altitude: 3,000 m (10,000 feet)
Maximum storage altitude: 12 km (40,000 feet)
Electro-Magnetic-Compatibility (EMC): EN 61326-1

for emission and immunity

Optically Isolated PC / Printer Interface

PC communication: Transfer instrument settings,
screen images, waveform data and waveform

ompatible w

referenc
for Window

T

FX
optional P

es, c

®

s

ia optional P

o printer:

v

Supports H

/LQ, Seiko DPU-414 and Postscript printers via

AC 91

ith FlukeView

0

M9

aserjet

P L

80.

®

, D

®

eskJ

software

et, Epson

Warranty

3 years, parts and labor on mainframe instrument
1 year on accessories

Accessories

Standard Accessories Fluke 199C, Fluke 196C, Fluke 199B, Fluke 196B, Fluke 192B

Rechargeable battery pack (installed) BP190
Line voltage adapter / Battery charger BC190
Voltage probes and accessories 10:1 voltage probe (VPS200, 1 red + 1 grey) including hook clip, ground lead with mini alligator clip, ground lead with

Multimeter test leads TL75 Hard Point test lead set (1red, 1 black)
User manual 10 language versions on CD-ROM, “Getting Started” booklet included with instrument

4 Fluke Corporation ScopeMeter 190C/190B Series and ScopeMeter 120 Series

hook clip, 4 mm add-on probe tip, ground lead to 4 mm banana plug

Technical Specifications

ScopeMeter 120 Series

Oscilloscope Mode

Vertical deflection

idth and Risetime Fluke 124 Fluke 123

Bandw

idth (risetime)

Bandw

with VPS40 probes 40 MHz 20 MHz

•

input A and B directly 40 MHz 20 MHz

•

ith STL120 Shielded Test Leads 12.5 MHz 12.5 MHz

w

•

Instrument risetime (input directly)

Number of inputs: 2
Input coupling: AC, DC with ground level indicator
Input sensitivity: 5 mV to 500 V/div (with the

included VPS40 (Fluke 124) and STL120 shielded test
leads measure up to 600 Vrms, CAT III)
Input voltage: 600 V CAT III. See General Specifica­tions for more detailed information

Vertical resolution: 8 bit
Accuracy: ± (2 % of reading + 0.05 x range/div)
Input impedance: 1 MΩ

shielded test leads; 1 MΩ
BB120; 5 MΩ ±1 % // 15.5 pF with VPS40, 10:1 Volt­age probe

±1 % // 225 pF with STL120

Horizontal

Max. sample rate (both channels simultaneously):

Fluke 124: 2.5 GS/s for repetitive signals; 25 MS/s for
single shot
Fluke 123: 1.25 GS/s for repetitive signals; 25 MS/s
for single shot

Number of digitizers: 2
Time base range: 10 ns/div to 1 min/div (Fluke 124);

20 ns/div to 1 min/div (Fluke 123)
Maximum record length: 512 Min-Max points
per input

Accuracy: ± (0.1 % of reading + 1 pixel)
Glitch detect: 40 ns

y and acquisition

Displa

Display modes: Input A, input A and B, envelope,
smooth
Acquisition modes: Normal (including glitch capture),
single shot, roll

Trigger and delay

Source: Input A, input B, external via optional ITP120
Modes: Automatic Connect-and-View, Free Run, Edge,

Single Shot, Video, Video Line
Connect-and-View: Advanced automatic triggering
that recognizes signal patterns and automatically sets
up and continuously adjusts triggering, time base and
amplitude. Automatically displays stable pictures of
complex and dynamic signals like motor drive and
control signals
Video triggering: NTSC, PAL, PAL+, SECAM. Includes
line select
Time delay: Up to 10 divisions pre-trigger view

Measurements

Vdc, Vac, Vac+dc, Vpeak max, Vpeak min, Vpeak
to peak, frequency (Hz), positive pulse width, negative
pulse width, positive duty cycle, negative duty
cycle, Amp ac, Amp dc, Amp ac+dc, Phase,
Temperature °C, Temperature °F, dBV, dBm into 50 Ω
and 600 Ω. (Amps, °C or °F with optional probes)

8.75 ns 17.5 ns

±1 % // 20 pF ± 3 pF with

Cursor Measurements (124 only)

ces:

Sour
Modes: Single or dual vertical cursor, dual horizontal

cursor, rise- or falltime

Measur

Single vertical line: A
time from start of rec
Dual vertical lines:
cursors, 1
Dual horizontal lines: High, low or ∆V - readout,
rise- and falltime: transition time, 0 %-level, 100 %­level, with markers at 10 % and 90 %
Accuracy: As oscilloscope

Input A, Input B

ements:

verage, min value, max value,

ording in roll mode

∆V at markers, time between

/T between cursors (in Hz)

Dual Input Meter

The specified accuracy is valid over the temperature
range 18 °C to 28 °C (64 °F to 82 °F). Add 10 % of
specified accuracy for each °C below 18 °C or above
28 °C (64 °F to 82 °F)
Max. meter bandwidth: 40 MHz (Fluke 124),
20 MHz (Fluke 123)

Voltage measurements

Measurement selection: Vdc, Vac rms, Vac+dc rms,
Vpeak max, Vpeak min, V

Ranges: 500 mV, 5 V, 50 V, 500 V, 1250 V
Full scale reading: 5,000 counts

Accuracy

± (0.5 % + 5 counts)

Vdc:
Vac rms:

1 Hz to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
20 kHz to 1 MHz ± (5 % + 20 counts)

Vac+dc true-rms:

DC to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
20 kHz to 1 MHz (5 % + 20 counts)

Vpeak:

Max peak or Min peak: 5% of full scale
Peak-to-peak: 10% of full scale

Ohms

Ranges: 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ
Max. resolution: 5,000 counts
Accuracy: ± (0.6 % of reading + 5 counts)

Capacitance

anges:

R
Max

ccuracy:±(2 % of reading + 10 counts)

A

50 nF to 500

. resolution:

5,000 c

Other meter functions

Frequency: Up to 70 MHz (Fluke 124) or up to 40 MHz
(Fluke 123)

Continuity: Beeper on < 30 Ω
Diode test: Up to 2.8 V
Amps: Amp dc, Amp ac, Amp ac+dc using an optional

current clamp or shunt. Scaling factors: 0.1 mV/Amp to
100 V/Amp
Temperature (°C, °F): With optional accessories. Scale
factors 1 mV/°C or 1 mV/°F

Number of inputs: 2
Input impedance: 1 MΩ ± 1 % // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,

TouchHold®, Relative measurements (zero reference),
TrendPlot recording

opeMeter 1

Sc

pk-pk

µF

ounts

/190B Series and ScopeMeter 120 Series Fluke Corporation 5

0C

9

Recorder Mode

Trendplot recording

Dual input electronic paperless chart recorder. Plots
and displays the actual, minimum, maximum and
average of any measurement.

Source and display: Input A, Input A and B
Range: 15 s/div to 2 days per division (automatic)
Recorded timespan: Up to 16 days with a resolution

of 1.5 hours
Recording mode: Continuous with automatic vertical
scaling and horizontal time compression
Measurement speed: 2.5 measurements per second
maximum
Horizontal scale: Time from start

General Specifications

Case

Design: Rugged, shock proof with integrated
protective holster

Drip and dust proof: IP51 according to IEC529
Shock and vibration: Shock 30 g Vibration 3 g

(sinusoidal) according to MIL-PRF-28800F Class 2

Display

Bright LCD with CCFL backlight, 60 (35) cd/m
with (without) power adapter

Size: 72 x 72 mm (2.8 x 2.8 inch)
Resolution: 240 x 240 pixels
Contrast and brightness: User adjustable,

temperature compensated

Memory Save and Recall

20 (10 in Fluke 123) instrument screens with user
set-ups and user text

Real-time clock

Time and date stamp TrendPlot recording

Power

Line power: Country specific line voltage
adapter/batter

Battery p

in Fluke 1
Fluke 1

Battery oper

up to 5 hours using B

Battery char

(Fluke 1

Battery p

ith adjustable power down time. On-screen battery

w
power indicator

y charger included

ower:

Rechargeable Ni-

MH BP130 (installed

24) or rechargeable NiCd BP120 (installed in

23)

ating time:

Up to 7 hours using B

P120

ging time:

5 hours (Fluke 1

24)

ower saving functions:

Auto power dow

2

P130,

23), 7 hours

n

Mechanical data

Size: 50 x 1

eight:1.2 kg (2.64 lbs)

W

15 x 232 mm (2 x 4.5 x 9.1 in)

Safety

Compliance: EN61010.1 (2nd Edition) Pollution degree
2, UL3111-1, CAN/CSA-C22.2 No. 1010.1,
ANSI/ISA S82.01

Input voltage ratings

Maximum input voltage: 600 V CAT III

(Maximum voltage between input and reference lead)

Maximum input voltage using VPS40 Probe: 600 V
CAT III, 1000 V CAT II

(Maximum voltage between

probe tip input and reference lead)

Floating voltage: 600 V CAT III

(Maximum voltage between earth ground and any
terminal (signal input or reference lead))

Maximum voltage between reference leads:

Instrument has common grounds connected via
self recovering fault protection. For different ground
potential measurements between inputs use DP120
differential voltage probe

Environmental

Operating temperature: 0 °C to +50 °C
Storage temperature: -20 °C to +60 °C
Humidity:

10 °C to 30 °C, 95% RH non condensing;
30 °C to 40 °C, 75% RH non condensing;
40 °C to 50 °C, 45% RH non condensing
Maximum operating altitude: 2,000 m (6,500 feet);
3,000 m (10,000 feet) voltages ≤ 400 V

Maximum storage altitude: 12 km (40,000 feet)
Electro-Magnetic Compatibility:

Emission EN50081-1 (EN55022 and EN60555-2)
Immunity EN50082-2 (IEC1000–4-2, -3, -4, -5)

Optically isolated PC/Printer interface

To printer: Supports HP Laserjet,®Deskjet,®Epson
FX/LQ and postscript printers via optional PAC91
To PC: Transfer instrument settings, screen images
and data, compatible with FlukeView®software for
Windows®via optional PM9080

arranty

W

3 years, parts and lab

essories

1 year on ac

c

or on mainframe instrument

Accessories

Standard Accessories Fluke 123, Fluke 124

Rechargeable battery pack (installed) BP120 (Fluke 123)

Line voltage adapter / Battery charger PM8907
Voltage probes and accessories STL120 Shielded Test lead set; VPS40 high impedance 10:1 probe, 40 MHz (1 black, included with Fluke 124 only);

Multimeter test leads
User manual 15 language versions on CD-ROM, “Getting Started” booklet included with instrument

6 Fluke Corporation ScopeMeter 190C/190B Series and ScopeMeter 120 Series

20 hook clips; g

C1

H

round leads w

ith mini alligator clips; AC120 alligator clips; BB120 BNC-to-Shielded banana adapter

TL75 Hard Point test lead (1 black)

30 (Fluke 1

P1

B

24)

International Safety Standards

Measurement
Voltage

y Summary description

Categor

CAT IV Three phase at utility connection, any outdoors

CAT III Three-phase distribution (under 1,000 V),

AT II Single-phase receptable connected loads

C

AT I Electronic

C

onductors (under 1,000 V)

c

Outside and service entrance

•

• Service drop from pole to building
Run between meter and panel

•
Overhead line to detached building

•

• Underground line to well pump

y III source

ommercial lighting

0 ft)

including single phase c
and distribution panels

• Feeders and short branch circuits
Distribution panel devices

•

• Heavy appliance outlets with “short”
connections to service entrance

Outlets and long branch circuits

•

• All outlets at more than 10 m (30 ft)
from Categor
All outlets at more than 20 m (6

•
from Category IV source

• Electronic equipment

• Low energy equipment with transient
limiting protection

To protect your instrument and – more importantly –
yourself, choose a test tool that can withstand the
electrical hazards present in the environment in which
you plan to use it.

EN61010 establishes international safety require­ments for electrical measurement equipment. It
separates the various electrical environments into

voltage-energy transients. To choose the right tool,
the voltage rating alone does not determine the
safety. It is the combination of voltage rating and
installation category that determines maximum tran­sient withstand capability of the tool. CAT III rated
instruments are recommended for measurement on
industrial power distribution systems.

installation categories based on the danger from high

FlukeView®ScopeMeter®Software for Windows

FlukeView software adds PC power to your
Fluke ScopeMeter Test Tools.

FlukeView Sc
out of your Sc

Store instrument

•

ith Fluke 1

(w
(Fluke 1

Copy color screen images into your reports and

•

documentation (color screen images with Fluke
190C Series only)

Capture and store waveform data from your

•

ScopeMeter on your PC
Create and archive waveform references for auto-

•

matic (Fluke 190C Series) or visual (Fluke 190B and
190C Series) comparison

Use cursors for parameter measurement

•

Includes wa

•

analysis
Copy waveform data into your spreadsheet for

•

detailed analysis
Extended recording of up to four user-selected

•

measurements help you monitor and analyze slow
moving signals and related events

Logging of other readings directly into other appli-

•

cation programs, eg., spreadsheet

opeMeter software helps you get more

opeMeter:

’s screen c

0C Series) or in black and white

9

0B and 1

9

20 Series)

veform analysis, e.g

opies on the P

., FFT spectrum

C, in c

olor

Add user text to instrument setups and send

•

these to the instrument for operator reference and
instructions

Capture complete Replay sequence into the PC for

•

further analysis and documentation
English, French and German versions included on a

•

single CD-ROM

Note: Some functionality may be
available with spe
models only

System re

Pentium 90 or better

•

CD-ROM drive

•

Window

•

T 4.0 / 2000 / X

N
One free RS 232 port

•

M9080 Optically isolated

P

•

S 232 adapter/cable,

R

vailable separately or

a

cific ScopeMeter

quirements

®

s

95 / 98 / Me /

P

included in

CC190/SCC120 kit and in

S

opeMeter ‘S’ versions

Sc

Supported Instruments

Full support for Fluke 199C, 199B, 199, 196C, 196B,
196, 192B, 192, 124, 123

®

opeMeter 1

Sc

/190B Series and ScopeMeter 120 Series Fluke Corporation 7

0C

9

Selection Guide

90C Color ScopeMeter Series 190B ScopeMeter Series 120 ScopeMeter Series

1

99C Fluke 196C Fluke 199B Fluke 196B Fluke 192B Fluke 124 Fluke 123

Bandwidth 200 MHz 100 MHz 200 MHz 100 MHz 60 MHz 40 MHz 20 MHz
Max real time sample rate 2.5 GS/s 1 GS/s 2.5 GS/s 1 GS/s 500 MS/s 25 MS/s 25 MS /s
Max equivalent time

sample rate

y 144 mm full color LCD 144 mm monochrome LCD 102 mm monochrome LCD

Displa

ital persistence Yes, gives analog oscilloscope like

Dig

Envelope mode

aveform compare Visual reference and automatic Visual reference —

W

FT analysis Windowing: Auto, Hamming,

F

Max record length

ope Mode: 3000 points per input channel

in Sc

opeRecord mode: 27,000 points per input or more (5 ms/div to 2 min/div)

in Sc

er of inputs 2 plus external / DMM input, all isolated from each other and from ground 2

Numb
Number of digitizers 2 2
Independently floating

isolated inputs
Input sensitiv
Glitch capture
Timebase range in

Scope mode
Trigger types Connect-and-View

Scope measurements

Waveform mathematics A + B, A - B, A x B, A versus B (X-Y-mode, giving Lissajous diagrams)

ScopeRecord trigger modes Start on trigger, stop on trigger, stop in absence of trigger signal —
Capture last 100 screens Automatic, with replay capability —
Dual input TrendPlot Yes, with cursors and zoom Yes
Memory for screens and 10 screens with set-up;

set-ups 5 more memories are made available upon registration of the ScopeMeter
Memory for recordings Two, each can store 100 scope screens, a ScopeRecord or a TrendPlot
True-rms multimeter 5000 counts, Volts, Amps, Ohms, Continuity, Diode, Temp
Safety certified 1000 V CAT II / 600 V CAT III (instrument and included accessories) 600 V CAT III (instrument and

(EN61010-1) included accessories)
Battery (installed) 4 hr Ni-MH BP190 7 hr NiMH 5 hr NiCd
Line Power Adapter / battery-charger included
Size 25 x 16.9 x 6.4 mm (10.1 x 6.7 x 2.5 in) 232 x 115 x 50 mm (9.2 x 4.5 x 2 in)
Weight 2 kg (4.4 lb) 1.2 kg (2.64 lbs)
PC and Printer Interface Using optional optically isolated RS-232 adapter/cable
Warranty 3 years on main instrument, 1 year on the standard accessories

ity 2 mV/div to 100 V/div 5 mV/div. to 100 V/div 5 mV/div to 500 V/div

Fluke 1

—

waveform decay (user selectable)

Up to 3 ns using pulse w

+ Automatic Vrms and watts cursors + 26 26 automatic

measurement on cursor limited —

+ Frequency Spectrum (FFT) —

Yes Yes Yes

ass / Fail’ testing

‘P

Hanning or none

N-Cycle, Dual Slope — —

part of waveform measurements

— — — — 2.5 GS/s 1.25 GS/s

——

——

512 min/max points per input

000 V between inputs, references and ground —

Up to 1

idth triggering; 50 ns peak detect at 5 ms/div to 1 min/div

5 ns/div to 2 min/div

, Free Run, Single Shot, Edge, Delay, Video Frame, Video Line Connect-and-View

™

Selectable pulse width and external Single Shot, Edge, Video

7 cursor measurements, 30 automatic measurements

Detailed technical specifications, optional accessories and a virtual product demo can be
found on the Fluke web site. Check it out at:

10 ns/div to 10 ns/div to 20 ns/div to

2 min/div 1 min/div 1 min/div

automatic measurements

ww.fluke.com/scopemeter

w

40 ns

20 10

—

, Free Run,

™

.

Ordering Information

opeMeter (200 MHz / 2.5 GS/s)

Color Sc

S

/

99C

Fluke-1

Fluke-199C Color ScopeMeter (200 MHz / 2.5 GS /s)
Fluke-196C/S Color ScopeMeter (100 MHz / 1 GS/s)

Fluke-196C Color ScopeMeter (100 MHz / 1 GS/s)
Fluke-1

Fluke-1
Fluke-1

Fluke-196B ScopeMeter (100 MHz / 1 GS/s)
Fluke-192B/S ScopeMeter (60 MHz / 500 MS/s) with

Fluke-192B ScopeMeter (6
Fluke-124/S Industrial Sc

Fluke-124 Industrial ScopeMeter, 40 MHz
Fluke-123/S Industrial ScopeMeter, 20 MHz, with

Fluke-123 Industrial ScopeMeter, 20 MHz
BP120 Rechargeable NiCd Battery for use with

with SCC190 kit

with SCC190 kit

opeMeter (200 M

Sc

S

/

99B

SCC190 kit

99B ScopeMeter (200 MHz / 2.5 GS/s)

ScopeMeter (100 MHz / 1 GS/s) with

S

/

96B

SCC190 kit

SCC190 kit

SCC120 kit

SCC120 kit

Fluke 120 Series

Hz / 2.5 G

Hz / 500 MS/s)

0 M

opeMeter, 40 M

S

Hz, w

/s) with

ith

y for use with

0 Series Sc

H Batter

S232 adapter/cable

opeMeters

ying case for

opeMeters

B

BP190 Rechargeable NiMH Battery for use with

SW90W FlukeView ScopeMeter Software for

M9

P
SCC190 Software - Cable - Case kit for Fluke

C

S

C195 Durable, universal soft carrying case for

C190 Hard shell protective carrying case for

C1

C1

DP120 Differential Voltage Probe for use with

VPS40 40 MHz, 10:1 Voltage probe set for use

Fluke 120 Series

Fluke 190 Series ScopeMeters

Windows
Optically isolated R

0

8

0

90 Series

1
Software - Cable - Case kit for Fluke

20

C1

120 Series

ScopeMeters and accessories

9

Fluke 1
Durable, protective soft carr

25

Fluke 120 Series ScopeMeters

20 Hard shell protective carrying case for

20 Series Sc

Fluke 1

Fluke 120 Series

with Fluke 120 Series

Rechargeable NiM

30

P1

Fluke. Keeping your world

up and running.

Fluke Corporation

O Box 9090, Everett, WA USA 98206

P

.

.V

Fluke Eur

PO Box 1186, 5602 BD
Eindhoven, The N

F

In the U.S.A. [phone] or
Fax [phone]
In Europe/
Fax [phone]
In Canada (800)-36-FLUKE or
Fax [phone]
From other countries [phone] or
F
W

©2004 Fluke Corporation. All rights reserved.
Trademark
Printed in U.S.A. 3/2004 1629083 D-ENG-N Rev D

ope B

etherlands

e information call:

or mor

East/Africa [phone] or

-

M

6

1

ax (425) 446-5

eb ac

1

ess: http://www

c

s are the property of their respective ow

.fluke.c

om/

ners

.