Flomatic C104-C Shematics

Automatic Control Valve
Written Specification (Purchase Specs)

Flomatic Corporation

Model C104-C/CA104-C
CS104-C (Global EU Model)
Pressure Reducing, Back Pressure (Sustaining) and External Check Valve
FULL PORTED

Sizes:
Globe: 1 1/2" - 30" (DN 40 - DN750)
Angle: 1 1/2" - 12" (DN40 - DN300)

Function:
The Pressure Reducing, Back Pressure (sustaining) with external check valve shall maintain a

preset constant downstream outlet pressure regardless of variations in the flow rate and/or inlet
upstream pressure. When the upstream becomes equal to the spring setting of the pressure
reducing control the main valve modulates to maintain a constant inlet pressure. The additional
external check valve shall cause the valve to close when the downstream (outlet) pressure is
greater than the upstream (inlet) pressure.

Main Valve Body:
The main valve shall be self contained hydraulically operated, single diaphragm-actuated globe or

angled body valve with no pistons operating the valve or pilot controls. The valve shall have three
major components: the body with seat installed, the cover with bushing installed, and the
diaphragm assembly. The diaphragm assembly shall be the only moving part. It shall form a
sealed chamber above the diaphragm to separate operating pressure from line pressure. Packing
glands and stuffing boxes are not permitted. The valve is designed for use with various types of
pressure and/or electric controls to provide the desired control of pressure or flow for a variety of
water system applications.

Description:
No separate chambers shall be allowed between the valve cover and body. The valve body and

cover shall be of cast material (Ductile Iron) with no fabrication or welding used in the
manufacturing process.

The valve shall contain a resilient, synthetic rubber seat seal, with a rectangular cross-section
contained on three and one half sides by the spool and seat plate, and form a tight seal against a
single removable seat ring. No O-ring type seal (circular, square or quad type) shall be permitted
as the seating surface. The seat plate shall be contoured to permit the smooth transition of flow
and hold the seat seal firmly in place.

The spool shall be of a sturdy one piece design (sizes 1 1/2" thru 4") capable of withstanding
opening and closing shocks. It must have straight sides and radius top to prevent excessive wear
to the diaphragm were it flexes across this surface. The spool shall be of a sturdy one piece design
(sizes 6" thru 24") capable of withstanding opening and closing shocks and having straight sides.

Flomatic Corporation
Glens Falls, NY 12801
Phone [phone]
Fax [phone]

C104-C Rev A (10/11)

March 30, 2003

1 of 3

The diaphragm assembly contains a non-magnetic 304 stainless steel stem of sufficient diameter
to withstand the high hydraulic pressure. It shall be fully guided at both ends and for the entire
range of travel, in the cover by a removable bushing and in the valve by an integral bearing in the
valve seat ring. No center guides shall be permitted. The stem shall be drilled and tapped in the
cover end to receive and affix such accessories as may be necessary. The diaphragm assembly
shall be the only moving part and shall form a sealed power chamber in the upper portion of the
valve, separating operating pressure from line pressure. The non-wicking, flexible, FDA approved
diaphragm shall consist of nylon fabric bonded with synthetic rubber compatible with the operating
fluid. The diaphragm must withstand a Mullins Burst Test of a minimum 600 psi per layer of nylon
fabric. It shall be tested 100,000 times to insure longevity. The diaphragm shall be fully supported
in the valve body and cover by machined surfaces with radius edges to prevent excessive wear as
the diaphragm flexes. The support must be no less than one-half of the total surface area of the
diaphragm in either the fully open or fully closed position.

The seat ring with integral bearing shall be a one-piece solid design and shall have a minimum of a
4° taper on the seating surface for a positive drip-tight shut off. The seat ring in 4" and smaller size
valves shall be threaded into the body. The valve seat ring in 6" and larger sizes shall be retained
by hex head bolts for ease of maintenance. The lower bearing of the valve stem shall be
contained concentrically within the seat ring and be exposed to the flow on all sides to avoid
deposits. Locating the valve body and cover shall be by a machined locating lip to insure proper
alignment of the valve stem. Pinning of the cover to the valve body shall not be permitted.

All necessary repairs and/or modifications other than replacement of the main valve body shall be
made possible without removing the valve from the pipeline. The valve manufacturer shall warrant
the valve to be free of defects in material and workmanship for a one year period from date of
shipment, provided the valve is installed and used in accordance with all applicable instructions.

The valve manufacturer shall be able to supply a complete line of equipment from 1-1/2" through
30" sizes and a complete selection of complementary equipment. The valve manufacturer shall
also provide a cavitation chart which shows flow rate, differential pressure, percentage of valve
opening, Cv factor, system velocity and if there will be cavitation damage.

Material Specification
Valve size:

Main Valve Body and Cover:
Main Valve Trim:
Connection:
Pressure Rating:
Temperature Range:
Rubber Material:
Coating:
Desired Options:

Flomatic Corporation
Glens Falls, NY 12801
Phone [phone]
Fax [phone]

C104-C Rev A (10/11)

March 30, 2003

2 of 3