Flir T4350BS, T4390BT User Manual

Quick Connection Guide

T4350BS / T4390BT SERIES

Thermal Bullet Camera

PACKAGE CONTENTS:

1 x IP Bullet Camera 1 x Mounting Template

4 x Mounting Screws 4 x Drywall Anchors

1 x Star Key

1 x RJ45 Waterproof Cap

1 x Power Pigtail

1

A

B

C

D

Installing the Camera

Use the included mounting template to mark holes
for the screws.

Drill holes for the mounting screws.

NOTE: Use the included drywall anchors if installing

into drywall.

Connect cables as shown in the section “Connecting
the Camera”.

Mount the camera to the surface using the included
mounting screws (4x).

2

A

Adjusting the Camera

Use the included Star key to loosen the adjustment
screw on the camera stand.

1. Loosen the lock screw to position the camera.

2. Tilt the camera on the stand up to 90°.

3. Rotate the camera around the stand.

2

3

1

3

A

B

C

Connecting the Camera

3

1

IP / PoE

1.

Ethernet Port: Connect the camera to a FLIR NVR or a router or switch on

your network using Cat5e or better Ethernet cable (not included). PoE Class
3 supported.

2.

Power: Connect a 12V DC or 24V AC power source if you are not using PoE.

3.

Video Out (BNC): Analog video output to a test monitor (optional).

MPX

1.

Ethernet Port: Install the MPX terminator.

When you power up the camera with the
MPX Terminator installed, the camera operates as an MPX camera.

2.

Power: Connect a 12V DC or 24 AC power source (300mA or higher).

3.

Video Out (BNC): Connect the camera to an FLIR MPX DVR. Video and

MPX camera control are supported over a standard coaxial cable.

Analog

Ethernet Port: Not used.

1.

2.

Power: Connect a 12V DC or 24V AC power source.

3.

Video Out (BNC): Connect the camera to an analog DVR.

2

4 5

12V DC Power Input Polarity

Quick Start Guides

1 x MPX Terminator

Latest software and manuals available on

www.flir.com/security/support

For support, visit

www.flir.com/security/support

Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2015 FLIR Systems, Inc. All rights reserved.

3.9” / 99mm

4.3”

109mm

Mounting screws (4x)

10.6” / 270mm

Drywall anchors (4x)

Weight

2.75lbs

1.25kg

B

For local recording, you can install a microSD card in the camera
up to 32GB. SanDisk™ or Kingston™ brand microSD cards are
recommended.

A

B
C

NOTE: For details on configuring microSD recording, see the
Instruction Manual.

Tighten the camera stand lock screw when finished.

Loosen the screw on the back of the camera body and
open the access door.

Insert a microSD card into
the microSD card slot.

Close the access door and
secure the screw.

microSD card slot

Audio / Alarm (Optional)

D

4.

Audio IO: See the Instruction Manual for details.

5.

Alarm IO: 1Brown—ALARM_COM; 2Purple—ALARM_NO;

3Red—Alarm_IN1; 4Yellow—Alarm_IN2; Pink—ALARM_GND.

Safety PrecautionsWeights & Dimensions Inserting the microSD Card (Optional)

• Use an appropriate low voltage power cable to prevent fire or electrical shock.

• If using DC power, make sure to follow the correct polarity as marked on the
power cable.

• Make sure to install the camera in an area that can support the camera
weight.

• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.

• Be careful not to leave fingerprints on the camera’s infared optics. Clean only
with low pressure fresh water and a lens cloth.

• Camera is rated for outdoor use (IP66), but is not intended for submersion in
water.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

T4350BS_T4390BT_SERIES_QCG_EN_R1