Flir ME313LB Specsheet

Contents

1 x 720p IR Eyeball Dome

4 x Mounting Screws

4 x Drywall Anchors

1 x Mounting Template

p

720 MPX IR EYEBALL DOME

MODEL: ME313L

1 x Allen Key

Features

• 1/2.9” Megapixel Sensor with 960H DSP*

• True Day/Night with Mechanical ICR

• Outstanding Image Clarity in Low Light Conditions

• Advanced 2D Digital Noise Reduction (2D-DNR)

• 90ft (28m) Smart IR Night Vision**

• 3.6mm Wide Angle Lens

• IP66 Weatherproof Rating***

• Cold Climate Capability (Minimum Operating
Temperature –22°F / –30°C)

• 3-Axis Design for Wall / Ceiling Mounting

• 12V DC Operation

* Compatible with FLIR MPX recorders only.
** IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on the
camera application.
*** Not recommended for submersion in water.

Safety Precautions

IT’S ALL ON THE WEB!

Product Information

User Manuals Quick Start Guides

Latest News

VISIT

Specification Sheets

Video Tutorials

QUICK START GUIDE

English Version 1.0

• Use an appropriate low voltage power cable to prevent
fire or electrical shock.

• Make sure to install the camera in an area that can
support the camera weight.

• There are no user serviceable parts inside the camera.
Please do not disassemble the camera.

• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens cover.

www.flirsecurity.com/pro

FLIR Systems, Inc.
Copyright © 2014
As our products are subject to continuous improvement, FLIR Systems
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE

www.flirsecurity.com/pro

Installing the Camera

Installation Diagram

Camera Specifications

ATTENTION - Test the camera prior to selecting a permanent

mounting location by temporarily connecting the camera(s) and
cables to the DVR.

To install the camera:

1. Use the included Allen key to loosen the screws on the
dome cover.

2. Rotate the camera base counterclockwise to separate
it from the ball camera and dome cover.

3. Feed the BNC / power cable through the camera
base. If you are running the cables against a wall
or ceiling, make sure to pass the cable through the
cable notch as shown above.

4. Connect the video and power cable as shown in the
section ‘Connecting the Camera’.

5. Mount the camera base to the mouting surface using
the included screws and drywall anchors (optional).

Setting up the Camera

1. Connect the BNC connector of the camera
to the video cable.

2. DC Power—Power Adapter: Connect a
12V DC Power Adapter (not included) to
the camera. Plug the Power Adapter into a
local power outlet.

• DC Power—Power Pigtail (not included):
Connect a Power Pigtail to the camera.
Connect the terminating wires of the cable
directly to the DC power source.

Image Sensor 1/2.9” 720p Megapixel CMOS

Video Format NTSC

Effective Pixels H: 1280 V: 720

Horizontal Resolution 900 TVL

Scan System Progressive

Sync System Internal

S / N Ratio 50dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/100,000 sec.

Min. Illumination 0.01 LUX (IR Off)

0 LUX (IR LEDs On)

Video Output Composite 1.0Vpp @ 75ohm

Lens Focal Length / Type 3.6mm F1.2 / Fixed

FOV (Diagonal) 90°

Termination BNC Type

IR Range / Qty. 90ft / 28m; 12 IR LED’s

Power Requirement 12V DC ± 10%

Power Consumption 200mA MAX with IR LED

Operating Temp. Range –22° ~ 140°F / –30° ~ 60°C

Environmental Rating IP66

Dimensions Diameter: 3.7” (94mm)

Height: 3.9” (98mm)

Weight (including stand) 0.7lbs / 0.3kg

6. Position the dome cover over the camera and screw it
clockwise halfway onto the camera base

7. Move the ball camera to the desired position. While
holding the ball camera firmly in place, screw the
dome cover the rest of the way to secure it to the
camera base. Holding the camera prevents it from
moving while installing the dome cover.

8. Use the included Allen key to tighten the screws on
the dome cover.

NOTE: For pigtail connection with 12V DC, make sure to
check polarity specifications on the power adapter.

WARNING - A REGULATED UL / CSA APPROVED 12V DC power

supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.

Dimensions

94mm / 3.7”

98mm / 3.9”