INSTRUCTION MANUAL
Ultra Resolution
Day & Night IR Dome Camera
Ultra Resolution
Day & Night IR Dome Camera
www.digimerge.com
V1.00
Vandal Model: DPV24DLR
Indoor Model: DPD24DLR
Please read this m anual thoroughly before use and keep it handy for futu re reference.
-ii--i-
INTRODUCTION
Features
All Models Feature:
• 1/3” Sony EX-View™ II 960H
• 2.8-12mm Varifocal Day/Night Lens F1.4 DC Iris
• 700+ TV lines of resolution
• Advanced Digital Noise Reduction (DNR)
• Shadow Reduction (ATR)
• Smart-IR Night Vision
• OSD menu control
• Privacy Masking / Motion Detection
• VIDEO OUT(BNC)
• Operates in 12VDC or 24VAC
• Test Monitor Output (RCA)
• 0 Lux with IR LED
DPD24DLR
• Indoor Dome Model
• Camera Mounting: Surface / Semi-Flush Mount
DPV24DLR
• Vandal Dome Model
•
IP66 Weatherproof and IK10 Vandal-proof
• Camera Mounting: Surface Mount
SPECIFICATIONS
General DPD24DL DPV24DL
Power source DC 12V / AC 24V +10%
Power consumption 6.6Watt Max
Minimum Power
Requirement
Image sensor
Total pixels 976 (H) x 494 (V)
Scanning system 2:1 interlace
Scanning frequency 15.734KHz(H), 59.95Hz(V)
Sync.system Internal / Line Lock
Resolution 700+ TV Lines
Min.illumination 0 Lux IR LED On
Video output 1.0 Vp-p (75 ohm, composite)
S/N Ratio more than 54dB (AGC OFF)
Power input 2-Pin terminal block (Detachable)
Video output BNC Connector (2nd video RCA)
Lens mount Fixed mount
Lens 2.8 - 12mm F1.4 Varifocal DC Auto iris
Operating temperature -10~50°C
Operating humidity 0-90% (non-condensing)
560mA
1/3” Sony EX-View™ II 960H
-1--iii-
MEASUREMENTS
3/4’’ -14
NPS thread
5.1"
(130 mm)
Vanda l Dome Di mensi ons Base h ole pos ition s
112 mm
4.4 in
5.1"
130 mm
Ind oor Dom e Dimens ions
4.4"
(112 mm)
Unders ide Bas e hole po sitio ns
137°
Ø 0.1"
3.5 mm
100.0 mm
3.9"
123°
100°
3.4"
87 mm
PACKING CONTENTS
Indoor Dome package contains the following:
Camera in housing ---------------------------------1
Camera Locking screws (PA3 Type) -----------2
Instruction guide (This Document) -------------1
Surface & Flush Mounting Templates----------2
RCA - BNC test cable ------------------------------1
Junction Box Plate ----------------------------------1
Mounting screw pack ------------------------------1
Vandal Dome package contains the following:
Camera in housing ---------------------------------1
Camera Locking screws (PM4 Type) ----------3
Instruction guide (This Document) -------------1
Surface Mounting Template ----------------------1
RCA - BNC test cable ------------------------------1
Junction Box Plate ----------------------------------1
Mounting screw pack ------------------------------1
Tamper allen key ------------------------------------1
Conduit Key ------------------------------------------1
JUNCTION BOX PLATE
Indoor dome to standard 2S, 4S and Octagon junction
boxes.
Junction Box Fiting plate -------------------------1
2S / 4S plate screws (KM3.5 Type) ------------4
Base Fitting Screws PWM3 ----------------------3
-------------2
Locking
Conduit
Screw
Mounting Screws Pack.
3pc 70mm / 2.8in Screws
3pc 30mm / 1.2in Screws
3pc 40mm 1.6in plugs
Base Fitting
Screw.
Key
Octagon
Screw
Allen Key
2S / 4S
Screw
27 mm
1.1 in
Ind oor Do me Flu sh Mo unt
Fitt ing dim ension s
39 mm
1.5 in
-2-
115 mm
4.5 in
Flu sh Mount Cutout
and Fitt ing Clearance
7 mm
.28 in
88.9 mm
3.5 in
83.3 mm
3.28 in
Screw hol e overv iew
46.0 mm
1.8 in
Base Fitti ng
Screw s
-3-
JUNCTION BOX INSTALLATION TYPES
2S FITTING
a. 2S Fitting requires only 2pcs of 2S/4S screws.
Note: You have a reduced space in which
Screws
Cable
Entr y
Screws
Cable
Entr y
Screws
Cable
Entr y
Screws
Cable
Entr y
to hide cables using this type of
installation. Recommended for indoor
dome only.
4S FITTING
a. 4S Fitting requires 2pcs of 2S/4S screws.
Suitable for both indoor and vandal domes.
Note:
TWO GANG FITTING
a.
of 2S/4S screws.
Note: A two gang provides the most robust
vandal domes.
OCTAGON FITTING
a.
Octagon screws.
Note:
are larger compared to those used for
the 2S/4S (M4 type). Suitable for both
indoor and vandal domes
-4-
VANDAL DOME FITTINGS
Wall Mount - model # MNTV2XW
Junction Box Mount - model # MNTV2XB
Mount for either Vandal or Indoor Dome.
Can also mount MNTV2XC or MNTV2XW.
Corner Mount bracket - model # MNTV2XR
Can fit either MNTV2XW or MNTV2XJ.
Junction Box Attachment for
MNTV2XW & MNTV2XC - model # MNTV2XJ
Fits either wall mount and ceiling mount.
Symmetrical design - reversible for top or bottom
conduit.
-5-
Pendant Mount - model # MNTV2XC
Pendant Cap - model # MNTV2XPC
Replaces the need for the camera base.
Compatible with ceiling conduit installations.
Pole Mount - model # MNTV2XP
Can fit either MNTV2XW or MNTV2XJ.
INSTALLATION. VANDAL DOME
1
2
a
b
3
a
b
ATTENTION - If using DC power, follow the correct
polarity as marked on the power cable.
1) Loosen the three tamper screws using the provided
allen key. Lift the dome cover.
Note: If you plan to use conduit fitting, remove conduit
cap using the provided conduit key.
Method 1 - Direct Attach Install
2a) Use the included mounting template (Installation
Option 2) to mark and pre-drill the required holes.
Remove 2 of the 3 base locking screws. Use 2pc of
the 2.8” screws to mount the camera directly to the
mounting surface.
Remove the 3rd base locking screw and install the 3rd
2.8” screw.
Go to step
OR
Method 2 - Camera Base Install
2b) Use the included mounting template (Installation
Option 1) to mark and pre-drill the required holes.
Remove the camera base by unscrewing the 3
base locking screws, and turn camera module
approx. 5 degrees counter-clockwise to detach
camera base from the camera module. Install the
base to the correct holes as indicated on the mount
template using the 1.2” screws. Go to step 3a.
Method 3 - Junction Box Install
2c)
(see page 4 for details). Remove the camera
base by unscrewing the 3 base locking screws,
and turn the camera module approx. 5 degrees
counterclockwise to detach camera base from
camera module. Install the base to the junction box
using the base attachment screws. Go to step 3a.
3a) Reinsert camera module into camera base by
aligning the arrow notches on the edge of the
camera module and the camera base (label on
edge of camera module indicates the location
of the arrow notch), and turning camera module
clockwise to lock into place.
3b) Use the 3 base locking screws to secure
camera base to camera module.
Go to step
In
stallation Option 1:
Use holes marked with 'A' when
installing camera base first.
Use short 30mm screws and anchors.
A
Installation Option 2:
Use holes marked with 'B' when
installing complete camera housing.
B
Use long 70mm screws and anchors.
Mounting Template Conduit Key Allen Key
4
4
-6-
A
B
B
A
on page 7 to complete installation.
on page 7 to complete installation.
INSTALLATION. VANDAL DOME
4
4) Remove camera cover by squeezing the back and front
of the cover (as indicated by the arrow indicators) at the
same time and lifting it up and away from the lens.
Arrow
5
6
7
5) Insert the included video test cable into the RCA jack and
connect to a test monitor to set up camera.
Video test cable
RCA Jack
Zoom
Focus
6a) Adjust camera viewing angle and secure into
screwdriver.
Note: Lens adjustment levers are by default in the
locked position. Turn counter clockwise to unlock.
Tighten levers to secure lens setting.
6b) Adjust lens and OSD as required.
6c) Re-attach the camera cover, using the thumb screw
as a guide, until it snaps into place.
7a) Re-attach the dome cover. Align arrows according to the
diagram below to ensure a weatherproof seal.
1
2
1
3
2
3
Correct arrow alignment
7b) Use the allen key to tighten the tamper screws.
Note: Make sure dome cover cord does not get caught in
the rubber seal.
-7-
Thumb Screw
Arrow on camera base
Arrow on camera module (inside camera)
Arrow on dome cover.
INSTALLATION. INDOOR DOME (Surface Mounting)
1
b
a
2
a
b
3
a
b
ATTENTION - If using DC power, follow the correct
polarity as marked on the power cable.
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
1b) While pressing on tab, twist the dome cover
counter clockwise just a few degrees to release
dome cover from back clips.
Lift off the cover.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and pre-
drill the required holes. Use included 2.8” screws to
mount the camera directly to the mounting surface.
3
Go to step
OR
Method 2 - Camera Base Install
2b) Use the included mounting template (Installation
Option 1) to mark and pre-drill the required holes.
Remove the camera base by unscrewing the base
locking screws (indicated by padlock markings)
and turn camera module approx. 5 degrees
counterclockwise to detach camera base from the
camera module. Install the base as indicated using
the 1.2” screws. Go to step 3a.
Method 3 - Junction Box Install
2c)
(see page 4 for details). Remove the camera
base by unscrewing the 3 base locking screws,
and turn the camera module approx. 5 degrees
counterclockwise to detach camera base from
camera module. Install the base to the junction box
using the base attachment screws. Go to step 3a.
3a) Reinsert camera module into camera base by
aligning the arrow notches, and turning camera
module clockwise to lock into place.
3b) Reinstall the base locking screws. (indicated
by padlock markings)
Go to step
on page 9 to complete installation.
3
on page 9 to complete installation.
-8-
INSTALLATION. INDOOR DOME (Semi-Flush Mount)
1
b
2
b
c
d
Thumb Screw
3
Zoom
Focus
a) Re-attach the camera cover, using the thumb screw as a guide, until it snaps into place.
4
b) Reattach dome cover.
ATTENTION - If using DC power, follow the correct
polarity as marked on the power cable.
1a) Press down on the tab marked with an arrow to lift
up the dome cover slightly
1b) While pressing on tab, twist the dome cover counter-
a
clockwise to release dome cover
1c) Remove the camera base by unscrewing the base
locking screws (indicated by a padlock markings)
and turn camera module approx. 5 degrees counterclockwise to detach camera base from the camera
module.
a)
Note: Always cut using the inside line of the cutout
template
b) Insert camera into cutout. Make sure that the
mounting arms are not extended.
c) Turn screwdriver clockwise to unlock all of the 3
mounting arms.
d) Continue turning clockwise to move mounting arms
down until they make contact with inner mounting
surface.
Note: Once mounting arms have made contact with
the inner mounting surface, do not apply too
much pressure to avoid damaging surface.
a) Remove camera cover by squeezing the back and front of
the cover as indicated by the arrow indicators at the same
time and lifting it up and away from the lens.
b) Insert the included video test cable into the RCA jack and
connect to a test monitor to set up camera. (see page 10).
c) Adjust camera viewing angle and secure into place by
Adjust lens and OSD as required.
Note: Lens adjustment levers are by default in the locked
position. Turn counter clockwise to unlock. Tighten
levers to secure lens setting.
-9-
CAMERA ADJUSTMENT CAMERA ADJUSTMENT
RCA Service Connector
Use supplied RCA - BNC cable
If you require BNC output.
MENU TREE SUMMARY
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
SHUTTER/AGC
WHITE BAL ATW
DAY/NIGHT EXT1
PICT ADJUST
NR
NEXT
EXIT SAVE ALL
AUTO
First Page OSD Menu
OSD function joystick. Pressing down
on joystick acts as ENTER function.
AUTO IRIS
TYPE DC
MODE AUTO
SPEED
RETURN
PICT ADJUST
MIRROR OFF
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
GAIN
RETURN
NR
NR MODE Y / C
Y LEVEL
C LEVEL
RETURN
080
000
128
128
128
150
004
004
AUTO
HIGH LUMINANCE
MODE
BRIGHTNESS
LOW LUMINANCE
MODE
BRIGHTNESS
RETURN
SPEED
DELAY CNT
ATW FRAME x1.00
ENVIRONMENT OUTDOOR
RETURN
DAY/NIGHT
BURST
DELAY CNT
DAY>NIGHT
NIGHT>DAY
RETURN
SHUT+AUTO IRIS
AGC
x0.50
ATW
OFF
SETUP MENU
BACKLIGHT OFF
ATR OFF
PRIVACY OFF
MOTION DET OFF
CAMERA ID OFF
SYNC INT
CAMERA RESET
BACK
EXIT SAVE ALL
032
239
016
005
003
005
Next Page OSD Menu
MANUAL SETUP
MODE SHUT+AGC
SHUTTER
AGC 6.00
RETURN
MANUAL WB
LEVEL
RETURN
B/W
BURST
MODE
LEVEL
RETURN
ATR
LUMINANCE MID
CONTRAST MID
RETURN
CAMERA ID
CAMERA
ABCDEFGHIJKLMNOPQRSTUV
WXYZ0123456789-!#$%&’
()_`.:;<=> @^*./^*X+/
CHR1 CHR2
CLR POS
RETURN
1/60
OFF
ONIR OPTIMIZER
AUTO
USER1 WB
058
015
B-GAIN
R-GAIN
RETURN
PRIVACY
AERA SEL 1 / 4
TOP
BOTTOM
LEFT
RIGHT
COLOR 1
TRANSP 1.00
MOSAIC OFF
RETURN
MOTION DET
DETECT SENSE
BLOCK DISP OFF
MOTION AREA ON
AREA SEL 1 / 4
TOP
BOTTOM
LEFT
RIGHT
RETURN
029
077
000
000
000
000
111
000
000
000
000
NOTE: Day / Night should be set to EXT1 on models with IR LEDs
-11--10-
CAMERA ADJUSTMENT CAMERA ADJUSTMENT
NR
OSD MENU control
Press down on the function joystick to access the setup menu.
• Main setup menu is displayed on the monitor screen.
SETUP MENU
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
WHITE BAL ATW
PICT ADJUST
NR
NEXT
EXIT SAVE ALL
Select a function by moving the joystick up and down and move left or right to
change setting value and press joystick to conrm selection.
If a menu option features a , a sub menu is available which can be accessed
by pressing down on the joystick.
Select ‘NEXT ’ to view remainder of the OSD setup menu
Select the language in which to display the OSD menu.
Note: Selection changes the language displayed immediatley.
LANGUAGE: English,Japanese,German, French
Russian, Portuguese, Spanish, Chinese.
LENS:
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
WHITE BAL ATW
PICT ADJUST
Changes the settings of the internal lens..
TYPE: MANUAL,AUTO
AUTO IRIS
TYPE DC
MODE AUTO
SPEED
RETURN
Once nished updating settings, highlight ‘EXIT’ and press down on the joystick
to exit setup menu.
To retain the changed settings after a power on/off of the camera you need to
select SAVE ALL option on the menu.
LANGUAGE
MODE: AUTO,CLOSE,OPEN
-AUTO: The mechanical iris is controlled automatically
-CLOSE: The mechanical iris is set to the closed position
-OPEN: The mechanical iris is set to the open position
Default setting is Auto
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
WHITE BAL ATW
PICT ADJUST
SPEED: 000-255
Sets the convergence speed of the mechanical iris.
Default setting is 80
080
-13--12-
CAMERA ADJUSTMENT CAMERA ADJUSTMENT
SHUTTER/AGC
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
DAY/NIGHT AUTO
Shutter has two options: AUTO or MANUAL
AUTO SETUP
HIGH LUMINANCE
MODE SHUT-AUTO IRIS
BRIGHTNESS
LOW LUMINANCE
MODE AGC
BRIGHTNESS x0.50
RETURN
40
MANUAL SETUP
MODE SHUT+AGC
SHUTTER 1/60
AGC 6.00
RETURN
AUTO
HIGH LUMINANCE
•
MODE: AUTO IRIS/SHUT+AUTO IRIS
•
BRIGHTNESS: 000-255
LOW LUMINANCE
•
MODE:
AGC / OFF
•
BRIGHTNESS:
MANUAL
•
•
•
6, 12, 18, 24, 30, 36, 42, 44.8
x0.25 / x0.50 / x0.75 / x1.00
MODE:
SHUT:
AGC:
SHUT+ AGC
Select shutter speed in x/second.
Default setting is 1/60
WHITE BAL
White Balance can be set to following:
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
WHITE BAL ATW
PICT ADJUST
NR
ATW / PUSH / USER1 / USER2 / ANTI CR
/ MANUAL / PUSH LOCK
-14-
ATW
ATW
SPEED
DELAY CNT
ATW FRAME x1.00
ENVIRONMENT OUTDOOR
RETURN
SPEED: 000-255
•
239
016
Default setting is 239
DELAY CNT: 000-255 Sets the time based of ATW
•
change. Default setting is
•
ATW FRAME: x0.50 / x1.00 / x1.50 / x2.00
16
Default setting is
ENVIRONMENT: INDOOR / OUTDOOR
•
Set the pull in frame of ATW
Default setting is
PUSH
USER1/USER2
Use white balance regardless of the subject conditions.
USER1 WB
029
B-GAIN
R-GAIN
RETURN
X1.00
INDOOR.
077
B-GAIN: 000-255 B Gain adjustment for WB
R-GAIN: 000-255 R Gain adjustment for WB
-15-
CAMERA ADJUSTMENT CAMERA ADJUSTMENT
PRIVACY
ANTI CR
Activates color rolling suppression.
•
DELAY CNT 000-255
MANUAL WB
•
MANUAL WB
058
LEVEL
RETURN
•
LEVEL 000-255
The actual variable range is limited to the range from the low color temperature
(approx. 1800K) to the high color temperature (approx. 10500K).
Default setting is 58
• PUSH LOCK
Press down on joystick to set current scene as the white
balance level. Use a grey card in front of lens to give a
natural white level.
DAY/NIGHT AUTO / BW / EXT1 / EXT2 /COLOR
SETUP MENU
EXPOSURE AUTO
PICT ADJUST
WHITE BAL ATW
WDR
DNR
DAY/NIGHT EXT1
Day/Night mode can be set to the following options: COLOR/AUTO/EXT/BW. Select
COLOR for a color image or BW for black and white. EXT1/EXT2 allows the use of an
external trigger to activate day/night operation. Use AUTO to have the camera
automatically adjust for Day/Night mode.
NOTE: Day/Night should be set to EXT1 on models with IR LEDs. EXT1 is used to sync
IR LED operation when going into B/W mode.
AUTO
•
BURST ON / OFF
Selects whether to output the burst signal when night
DAY/NIGHT
BURST OFF
DELAY CNT
DAY - NIGHT
NIGHT - DAY
RETURN
003
002
005
DAY - NIGHT 000-255
Threshold for Night status from day status.
•
NIGHT - DAY 000-255
Threshold for the Day status from night status.
B/W
B/W SETUP
BURST ON
IR OPTIMIZER ON
MODE AUTO
LEVEL
RETURN
Allows additional Smart IR settings to be enabled.
IR OPTIMIZER
•
Smart IR must be enabled/disabled through the B/W menu. Smart IR is enabled by
default on models with IR LEDs, and works when Day/Night is set to EXT1, Auto, or
B/W.
•
MODE
feature to center of image or automatic area.om
•
LEVEL
ADJUST
PICT
ON / OFF Turn Smart IR feature ON/OFF.
AUTO / CENTER
When IR Optimizer is ON, set Front Light Compensation F C
Adjust Level for Smart IR
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
WHITE BAL ATW
PICT ADJUST
NR
Picture and display control settings
• MIRROR: ON / OFF
• BRIGHTNESS: 000-255 Screen brightness.
• CONTRAST: 000-255 Screen contrast.
• SHARPNESS: 000-255 Screen sharpness.
• HUE: 000-255 Adjust the hue.
• GAIN: 000-255 Adjust the gain.
16
PICT ADJUST
MIRROR OFF
BRIGHTNESS
CONTRAST
SHARPNESS 128
HUE
GAIN
RETURN
-17--16-
000
128
128
150
SETUP MENU
LANGUAGE ENGLISH
LENS AUTO
WHITE BAL
ATW
CAMERA ADJUSTMENT CAMERA ADJUSTMENT
NR
Digital Noise Reduction.
This function reduces the background noise in a low luminance environment.
NR MODE: “Y/C” / “OFF” / “Y” / “C”
Noise reduction Filter mode.
Y LEVEL:
C LEVEL:
NEXT
From the main menu select NEXT to enter the second page of the menu.
SETUP MENU
BACKLIGHT OFF
ATR OFF
PRIVACY OFF
MOTION DET OFF
CAMERA ID OFF
SYNC INT
CAMERA RESET
BACK
EXIT SAVE ALL
BACKLIGHT OFF / BLC / HLC
-OFF Backlight compensation OFF
-BLC Backlight compensation ON
-HLC High light compensation ON
NR
NR MODE Y / C
Y LEVEL
C LEVEL
RETURN
Default setting is 4
Default setting is 4
SAVE
ALL
PICT ADJUST
NR
NEXT
EXIT
004
004
SHADOW REDUCTION (ATR)
OFF / ON
This function compensates for darker areas surrounding the object to provide
naturally sharp picture and improves contrast in bright/dark areas.
ATR
LUMINANCE MID
CONTRAST MID
RETURN
• LUMINANCE
• CONTRAST
Sets the extent of the luminance compression
(MID/HIGH/LOW)
Sets the extent of the contrast enhancement
(MID/MIDHIGH/HIGH/LOW/MIDLOW)
PRIVACY OFF / ON
Hide an area so that it is not displayed on the monitor.
PRIVACY
AREA SEL 1 / 4
TOP
BOTTOM
LEFT
RIGHT
COLOR 1
TRANSP 1.00
MOSAIC OFF
RETURN
AREA SEL: Selects the mask frame to be adjusted.
TOP: Sets the top side of the mask frame selected by the
AREA SEL parameter
BOTTOM: Sets the bottom side of the mask frame selected by the
AREA SEL parameter.
LEFT: Sets the left side of the mask frame selected by the
AREA SEL parameter.
RIGHT: Sets the right side of the mask frame selected by the
AREA SEL parameter
COLOR: Sets the colors of the mask frames
TRANSP: Sets the transparency ratio of the mask frames.
MOSAIC: Sets the mask frame mosaic to ON or OFF
000
000
000
000
-19--18-
CAMERA ADJUSTMENT CAMERA ADJUSTMENT
MOTION DET OFF / ON
Motion Detection is dened by rectangular areas. This give a visual identication
of motion areas.
MOTION DET
DETECT SENSE
BLOCK DISP OFF
MOTION AREA ON
AREA SEL 1 / 4
TOP
BOTTOM
LEFT
RIGHT
RETURN
DETECT SENSE: Sets the motion detection sensitivity
BLOCK DISP: ON/OFF/ENABLE status of the motion detection
block display.
ON: Make motion areas visible, OFF: Hide motion areas
ENABLE Press enter to access the “dead band setting”
111
000
000
000
000
BOTTOM: Set the bottom side of the monitoring frame selected by the AREA
SEL parameter
LEFT: Set the left side of the monitoring frame selected by the AREA SEL
parameter.
RIGHT: Sets the right side of the monitoring frame selected by the AREA SEL
parameter
CAMERA ID OFF / ON
Camera ID shows a name on the screen as chosen.
CAMERA ID
CAMERA
ABCDEFGHIJKLMNOPQRSTUV
WXYZ0123456789-!#$%&’
()_`.:;<=> @^*./^*X+/
CHR1 CHR2
CLR POS
RETURN
screen, on-screen cursor moves in response to the
inputs Left, Right, Up and Down to set the sensing area,
or dead band for specied blocks. This allows you to
specify and set an area of motion which is not
rectangular in shape.
Press and hold SET button 3 seconds to exit.
Use Up/Down/Left/Right to move around. CHR1/2 changes the selection fonts to
alternative selection, CLR will clear info. POS allows position change.
MOTION AREA: ON / OFF Enable / Disable Area No.
AREA SEL: 1/4 / 2/4 / 3/4 / 4/4. Selects motion area number.
TOP: Set the top side of the monitoring frame selected by the AREA SEL
parameter.
-21--20-
CAMERA ADJUSTMENT
TROUBLE SHOOTING
LL
PHASE
RETURN
SYNC INT / LL
Video synchronization displayed
INT(Internal) or LL (Line Lock)
Note: Shows INT with DC only model.
And LL setting for camera model
when connected to a AC supply.
PHASE: 000-524
Adjust the phase in the vertical direction when the line
lock mode is available.
• CAMERA RESET
This will reset all settings for all menus to manufacturer
defaults. This allow you to return to shipped settings
from the manufacturer.
EXIT / SAVE ALL
• EXIT Exit OSD menu.
• SAVE ALL Saves the settings to camera
326
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
Nothing appears on the screen.
Check that the power cord and line connection between the camera and monitor are connected properly.
Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
The image on the screen is dim.
Is lens stained with dirt? Clean lens with soft, clean cloth.
Adjust the monitor contrast & brightness controls
Re-position the camera if necessary.
The image on the screen is dark.
Adjust the contrast feature of the monitor.
If you have an intermediate device, set the 75Ω / Hi-z properly.
The camera is not working properly, and the surface of the camera is hot.
Check that you have properly connected the camera to an appropriate power source.
IR LED's don't appear to be working (not glowing red in the dark)
Ensure that the power provided to the camera at the camera end meets the power consumption
requirements as per the camera specications.
The Motion Detection function does not work.
Check that MOTION DET in SETUP 2 menu is ‘ON’ for the selected area.
Enable Block display ON will show a visual indication on the display output for the detected areas.
Color is not correct.
Check the setting of WHITE BAL SETUP menu.
Under certain incandescent lighting,some color shifting may take place.
This is normal due to sensitivity to IR light
When the resistance value of copper wire is at [20˚C(68˚F)]
Copper wire size (AWG)
Resistance (Ω/m)
Voltage Drop (V/m)
As shown in the table above, voltage decreases as the wire gets longer. Therefore use of
an excessively long adaptor output line for connection to the camera may affect the
performance of the camera.
*Standard voltage for camera operation : AC 24V ±10% or DC 12V ±10%
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
#24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2)
0.078 0.050 0.030 0.018
0.028 0.018 0.011 0.006
Notes
• Be sure to connect power only after all the installation is complete.
• Use the UL listed, CLASS 2 power transformer for AC24v adaptor.
-22-
-23-
Loading...