Flir DBB44TL Quick User Guide
Contents
1 x Weatherproof IR Bullet
Camera with Varifocal Lens
IT’S ALL ON THE WEB!
Product Information
Specification Sheets
1 x Sunshade Housing
1 x Fastening Screw
3 x Mounting Screws
1 x Hex Allen Key
1 x Flat-head Allen Key
2 x Rubber Weatherproofing Plugs
Features
• Ultra Resolution 1/3” Image Sensor / 600TVL
• True Day / Night with Mechanical ICR
• 2.8–12mm Varifocal Lens
• Cold Climate Capability (Operates to -22°F/ -30°C)
• 90ft (27m) Smart IR Night Vision Range*
• IP66 Weatherproof Rating**
• Cable Through Bracket Design
• External Zoom / Focus Adjustment
• Wall / Ceiling Mountable
• 12V DC Operation
* IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on the
camera application.
** Not intended for submersion in water. Installation in a sheltered
area is recommended.
User Manuals
Latest News
Quick Start Guides
Video Tutorials & Demos
ULTRA RESOLUTION VARIFOCAL
OUTDOOR IR BULLET CAMERA
MODEL: DBB44TL
QUICK START GUIDE
English Version 3.0
Safety Precautions
• Use an appropriate low voltage power cable to prevent fire
or electrical shock.
• Make sure to install the camera in an area that can support
the camera weight.
• There are no user serviceable parts inside the camera.
Please do not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material.
Please use a soft cloth to clean the lens cover.
VISIT
www.digimerge.com
Digimerge Technologies Inc.
Copyright © 2013
As our products are subject to continuous improvement, Digimerge
reserves the right to modify product design, specifications and prices,
without notice and without incurring any obligation. E&OE
www.digimerge.com
Installing the Camera
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the camera(s) and
cables to the DVR.
1. Set the camera in the desired mounting position
and mark holes for the screws.
2. Drill the holes for the mounting screws.
3. Connect the video and power cables as shown in
the next section ‘Setting up the Camera‘.
4. Mount the camera stand to the desired surface
using the provided screws.
5. Place the sunshade on top of the camera with
the large end pointing in the same direction as
the lens. Insert the sunshade screw.
6. Set the position and angle of the camera using
the provided Hex Allen Key.
2. Loosen the screw near the stand
and adjust the camera’s vertical
position.
Setting up the Camera
1. Connect the BNC connector of the camera to
the video cable.
2. DC Power—Power Adapter: Connect a
12V DC Power Adapter (not included) to the
camera. Plug the Power Adapter into a local
power outlet.
• DC Power—Power Pigtail (not included):
Connect a Power Pigtail to the camera.
Connect the terminating wires of the cable
directly to the DC power source.
NOTE: For pigtail connection with 12V DC, make sure
to check polarity specifications on the power adapter.
ATTENTION - This camera includes an Auto Mechanical IR Cut Filter.
When the camera changes between Day/Night viewing modes, an
audible clicking noise may be heard from the camera. This clicking is
normal, and indicates that the camera filter is working.
3. Use the short arm of the provided Flat-head
Allen Key to adjust the ZOOM and FOCUS
control screws as required.
ZOOM
FOCUS
Camera Specifications
Image Sensor 1/3” Color Image Sensor
Video Format NTSC
Effective Pixels H: 728 V: 488
Horizontal Resolution 600 TVL
Scan System 2:1 Interlace
Sync System Internal
S / N Ratio 52dB (AGC Off)
Iris AES
AES Shutter Speed 1/60 ~ 1/12,000 sec.
Min. Illumination 0.2 LUX @ F1.2 (IR Off)
Video Output Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type 2.8–12mm F1.7 / Varifocal
FOV (Diagonal) 27° ~ 92°
Termination Video: BNC Female
IR Range / Qty. 90ft / 27m; 36 IR LED`s
Power Requirement 12V DC ± 10%
Power Consumption 12V: 340mA MAX with IR LED
Operating Temp. Range –22° ~ 122°F / –30° ~ 50°C
Environmental Rating IP66
Dimensions (LxWxH) 8.3” x 3.9” x 3.3”
Weight (including stand) 1.2lbs / 0.5kg
0 LUX (IR LEDs ON)
210mm x 98mm x 85mm
Dimensions
98mm / 3.9”
210mm / 8.3”
1. Twist the ring to tighten/
loosen the stand connection
and adjust the camera’s
horizontal position.
WARNING - A REGULATED UL / CSA APPROVED 12V DC power
supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.
3. If needed, loosen the screw near
the camera and twist the camera
head on the mounting stand.
85mm / 3.3”
4. Insert rubber weatherproofing plugs (2x)
firmly into the ZOOM and FOCUS screwholes to ensure a weatherproof seal.
Weatherproofing
Plugs
Loading...