Flint & Walling NightBright Lighting System User Manual
Operating Instructions & Parts Manual
!
!
!
!
!
!
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
NightBright Lighting System
FW1356
0410
Supersedes
NEW
Description
This lighting system is designed for use with 115V floating fountain systems.
Optional colored lamp kits are available in red, green and blue. All mounting
hardware is included to attach lights to fountain.
General Safety Information
Carefully read and follow all
safety instructions in this manual.
Keep safety labels in good condition.
Replace missing or damaged safety
labels.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on
the pump or in the manual, look for
one of the following signal words and
be alert to the potential for personal
injury or property damage.
Warns of hazards
that WILL cause
serious personal injury, death or major
property damage if ignored.
Warns of hazards
that CAN cause
serious personal injury or death, if
ignored.
Warns of hazards
that MAY cause
minor personal injury, product or
property damage if ignored.
IMPORTANT: Indicates factors
concerned with operation, installation,
assembly or maintenance which could
result in damage to the machine or
equipment if ignored.
NOTE: Indicates special instructions
which are important but are not
related to hazards.
Read these
warnings and
instructions carefully. Failure to follow
could result in serious bodily injury
and/or property damage.
This product
contains chemicals
known to the State of California to
cause cancer and birth defects or other
reproductive harm.
This unit
tested for use in swimming
pool areas.
not
Hazardous voltage.
Can shock, burn
or cause death.
Ground system before
connecting to power
supply.
with a 100 ft power cord with
connect to properly grounded
receptacle of grounding type. Do not
remove ground pin on plug. Do not
extend the cord length by splicing or
with an extension cord.
GROUNDED RECEPTACLE MAY RESULT IN
SEVERE ELECTRICAL SHOCK.
circuit breaker of proper size.
objects, oil, grease, hot surfaces
or chemicals. DO NOT kink the
power cable. If damaged replace
immediately.
mechanical damage which could produce
serious electrical shock and/or equipment
failure.
or covers open (either partially or
completely) when not being worked
on by a competent electrician or
repairman.
three prong GFI plug. – Must
TO CONNECT THIS UNIT, WITH
THE GFI, TO A PROPERLY
Be sure system is connected to a
circuit equipped with a fuse or
Protect the power cable from
coming in contact with sharp
Install all electrical equipment
in protected area to prevent
NEVER leave the control box,
fused disconnect switch,
Electrical
installations shall be in
accordance with
National Electric
Code (NEC) and all
applicable local
codes and ordinances. A licensed
electrician should
perform installation.
System
furnished
FAILURE
Specifications
120 volt
3 - LED lamps
100 ft. power cord with GFI
Always disconnect power source
before performing any work on
or near the motor, lights or connected
load. If the power disconnect point
is out-of-sight, lock it in the open
position and/or tag it to prevent
unexpected application of power.
Failure to do so could result in fatal
electrical shock or bodily injury.
DO NOT use this system in
flammable liquids such as
gasoline, fuel oil, kerosene, etc. Failure
to follow this warning could result in
property damage and/or personal
injury.
Unpacking
Unpack and inspect system for damage.
Verify you have received the following
components:
1. Instructions
2. Warranty
3. Lights with 100 ft. power cord with
GFI. Check for any bent prongs or a
cracked case on the GFI.
4. Mounting hardware
a. Brackets (3)
b. 1/4-20 x 5/8 bolts (6)
c. 1/4-20 locknuts (3)
d. 1/4 lock washer (3)
5. Wire tie
INSTALLATION INSTRUCTIONS
1. Required Tools and Supplies:
a. 7/16" wrenches (2)
b. Multimeter to check voltage,
current and insulation resistance to
ground
2. Install Nightbright lighting system
to float. (See Fig 1).
023415
Operating Instructions and Parts Manual
!
!
IL1066
TEST
RESET
WARNING
TEST
RESET
WARNING
NightBright Lighting System
Installation (Continued)
a. Assemble lights (1) to mounting
brackets (2) using bolts (3), and
locknuts (5).
b. Attach light/bracket assemblies to
the threaded inserts in top of float,
using bolts (3) and lockwashers (4).
(Install in alternating inserts if 6
inserts are present in float.)
c. Adjust lights to provide desired
illumination. (See Fig 1).
d. Tighten all bolts & screws until
seated.
e. Attach light system cord to
fountain system cord with
included nylon wire tie.
Never enter the water either
wading, swimming or in a
boat with the pump power on, as this
may result in severe electrical shock.
3. Only install this system in ponds
where no swimming, wading,
boating or fishing is allowed.
Disconnect power to system before
fishing or entering the water.
4. Post appropriate warning signs per
local and state codes.
5. Place power cord so that it rests on
bottom of pond away from sharp
rocks or vegetation so it can be easily
removed without being damaged or
becoming entangled. Leave enough
slack to accommodate anticipated
water level fluctuations.
NOTE: It is suggested that the
underwater power cables be installed
in conduit from the panel to 4 -5 ft into
the water to prevent possible cable
damage.
6. Before connecting the unit to the
power receptacle, check to insure
there is no leakage to ground. This
can be done by using an ohm meter
and setting the scale to its highest
setting (i.e. Rx100K). Connect one
ohmmeter lead to the unit power
cord ground (round prong) and to
one of the flat prongs. It should
read infinite or at least 2 mega
ohms. Repeat with the other prong.
If reading is below 2 mega ohms
on either prong contact Customer
Service Help Line listed at bottom of
page.
"NO SWIMMING” AND OR
POSTED PER STATE AND LOCAL CODES.
velocity and can cause bodily injury if
contact is made.
in damp areas. If possible, avoid all
contact with electrical equipment
during thunderstorms or extreme
damp conditions.
7. Do Not Operate System on an
8. After installing
WARNING SIGNS SHOULD BE
Water leaving
nozzle is at high
Always use caution when
operating electrical controls
Extension Cord. If no power is
accessible at the pond, contract a
licensed electrician to install the
proper power supply in accordance
with National Electric Code and
all applicable local codes and
ordinances.
the unit,
checking ground
and connecting
power to the
unit, the unit can
be powered up.
Check operation
of the GFI by
pushing the
“Test” button,
the unit should
stop. Pushing
the “Reset”
button should
restart the unit.
If pressing the
Figure 1 - Installation
6
“test” button does not stop the unit,
immediately shut off power to unit
and contact Customer Service Help
Line listed at bottom of page.
FAILURE TO CONNECT THIS
UNIT, WITH THE GFI, TO A
PROPERLY GROUNDED POWER SUPPLY
MAY RESULT IN SEVERE ELECTRICAL
SHOCK.
INSTALLATION CHECK LIST
Read installation instructions and
warnings.
Post appropriate warning signs.
Install NightBright lighting system
to float.
Check insulation resistance to
ground.
Power up unit.
Test operation of GFI by pressing the
“Test” Button.
File instructions for future reference.
DO NOT handle pump or
lights with wet hands or
when standing in water as fatal
electrical shock could occur.
Disconnect main power supply before
handling system for any reason.
3
4
5
2
3
1
2
95 North Oak Street • Kendallville, IN 46755
Copyright 2009. All rights reserved.
Loading...