Fishman TSV User Manual
Routing Template
®
Intonation
Screws
Saddle Height
Adjustment Screws
Vibrato Bar
Tension Adjust
Stereo Output Jack
(Tip/Ring/Sleeve)
Stereo "Y" Cable
Powerbridge™
Signal
(Ring)
Pure
Magnetic
Signal
(Tip)
Powerbridge™
Stereo
Instrument Cable
to Stereo Input
Magnetic
5 M
Ω
Resistor
Shielding Foil
Stereo Output Jack
Mounting Screws
2 Vibrato Claw
F
•
•
•
•
•
•
•
3mm Hex Wrench
•
Vibrato Arm
•
Vibrato Claw & Springs
•
1.5 mm Hex Wrench
•
2 Pivot Screws
•
2 Pivot Screw Bushings
•
TSV Powerbridge™ Pickup
ISHMAN
System Components
• Stereo Jack
Parts List
Users Guide that accompanies these instructions.
style guitar, please read the Powerbridge™
®
how to integrate it with your Strat
variety of wiring options available for the Powerbridge™. To help you decide
Thank you for choosing the Fishman TSV Powerbridge™ Pickup. You will find a
P
OWERBRIDGE
(included)
™ P
A 1/4" stereo output jack is
provided with your
Powerbridge™ Pickup. It is an
essential component to the
Powerbridge™ System.
It can send piezo and magnetic
pickup signals to separate
amplifiers. The magnetic
pickups are wired to Tip, and
the Powerbridge™ Pickup is
wired to Ring.
ICKUP
I
NSTALLATION
NOTE: To minimize cross-talk, use a "2 Pair" premium stereo cable (available
through your Fishman dealer) with separate shielding for both the Powerbridge™
and magnetic signals.
G
UIDE
3 - Mono Instrument Cable
With a Fishman Powerchip™:
Powerbridge™ together on the guitar you’ll need a Fishman Powerchip™. Plug
a standard mono cable into a Powerchip™ equipped guitar and you can mix
piezo and magnetic signals right on the instrument.
User’s Guide for Powerchip™ description.)
If you want to blend the magnetics and the
(See the Powerbridge™ System
Bridge / Pickup System
Two Stud Vibrato Style
M
TSV
ODEL
PICKUP
POWERBRIDGE
™
G
UIDE
L
IMITED
INSTALLATION BY A QUALIFIED PROFESSIONAL REPAIRMAN IS STRONGLY
RECOMMENDED. FISHMAN TRANSDUCERS WILL NOT BE RESPONSIBLE FOR ANY
DAMAGES THAT MAY RESULT FROM IMPROPER INSTALLATION.
The Fishman Powerbridge™ Pickup is warranted to function for a period of One (1) Year
from the date of purchase. If the unit fails to function properly within the warranty period,
free repair and the option of replacement or refund in the event that Fishman is unable
to make repair are Fishman’s only obligations. This warranty does not cover any
consequential damages or damage to the unit due to misuse, accident, or neglect.
Fishman retains the right to make such determination on the basis of factory inspection.
Products returned to Fishman for repair or replacement must be shipped in accordance
with the Return Policy, as follows. This warranty remains valid only if repairs are
performed by Fishman. This warranty gives you specific legal rights and you may also
have other rights which may vary from state to state.
RETURN POLICY
To return products to FISHMAN TRANSDUCERS, you must follow these steps...
1. Call FISHMAN TRANSDUCERS at 978-988-9199 for a Return Authorization Number
(“RAN”).
2. Enclose a copy of the original Bill of Sale as evidence of the date of purchase, with
the product in its original packaging and a protective carton or mailer.
3. FISHMAN TRANSDUCERS’ technicians will determine whether the item is covered
by warranty or if it instead has been damaged by improper customer installation or
other causes not related to defects in material or workmanship.
4. Warranty repairs or replacements will be sent automatically free of charge.
5. If FISHMAN TRANSDUCERS determines the item is not covered by warranty, we will
notify you of the repair or replacement cost and wait for your authorization to
proceed.
FISHMAN TRANSDUCERS, INC.
340-D Fordham Road Wilmington MA 01887 USA
Phone 978-988-9199 • Fax 978-988-0770
Fishman's bridge system fits on the Fender Stratocaster® guitar or Fender Telecaster® guitar and other similar and comparable guitars. • FENDER,
STRAT, AMERICAN STANDARD STRAT, AMERICAN STANDARD TELE, TELE are registered trademarks of Fender Musical Instruments Corp.
with which Fishman Transducers Inc. is not affiliated.
www.fishman.com
W
ARRANTY
009-075-001 • Rev 4 • 4-9-02
I
NSTALLATION
ICKUP
P
™ P
NSTALLATION
I
OWERBRIDGE
G
™
POWERBRIDGE
PICKUP
M
ODEL
Two Stud Vibrato Style
Bridge / Pickup System
Direct Replacement for “Knife-Edge” Stratocaster Bridge
TSV
®
result from handling these wires.
Important!
UIDE
978-988-9665 or tech@fishman.com
that may result from improper installation.
assistance, contact Fishman Customer Support at
Please read these instructions carefully. For technical
Fishman Transducers will not be responsible for any damages
Installation by a qualified professional repair-person only.
saddles.They are extremely delicate. Pickup failure may
Do not disturb the black signal wires located under the
ISHMAN
F
• Instrument Cable
Depending on how you want to set up your Powerbridge™ system, you can use
one of the following three instrument cables (available from your Fishman
dealer).
(not included)
1 - Stereo "Y" Cable
This will split the
Powerbridge™ and magnetic
pickup signals and send them
to separate amplifiers or other
destinations (PA, recording
devices, etc.).
2 - Stereo Instrument Cable
Both magnetic and piezo signals can be sent through a single stereo instrument
cable to our Powerblend™ pedal. From there, magnetic and piezo signals can
be either combined to a single mono output or split to separate stereo outputs.
Powerchip™
Powerbridge™
Mono Instrument Cable
Without a Fishman Powerchip™:
the Powerbridge™ Pickup, but your magnetics will function
before you installed the Powerbridge™.
Stereo Output Jack
(Tip/Ring/Sleeve)
Optional Passive
Volume Pot
Mono Instrument Cable
Magnetic
A mono instrument cable will short out
Powerbridge™
Magnetic
exactly
as they did
• Basic Passive Setup
Stereo Outputs
The simplest way to get the Powerbridge™ Pickup up and running is to wire it and the
magnetic pickups to Tip/Ring outputs of the supplied stereo jack. A stereo "Y" cable
or a standard stereo cable can then carry the two signals. From there, all mixing and
blending functions will be performed offboard the instrument. A Fishman
Powerblend™ pedal is especially suited for offboard blending/mixing with this passive
setup.
For a passive setup, don't tie the Powerbridge™ and magnetic pickup wires together
to a guitar's mono output jack. This may seem like a good idea, but it won't work. If
you connect the piezo and magnetic outputs, you will experience a loss of tone and
a very bizarre and un-musical interaction between the Powerbridge™ and magnetic
pickups.
Magnetic and piezo pickups operate on different electrical platforms. Magnetics are
"inductors" and piezos are "capacitive" devices. To mix signals on the instrument
you’ll need to electronically isolate or "buffer" the two signals with an active mixing
circuit like the Fishman Powerchip™.
Stereo Output Jack
(Tip/Ring/Sleeve)
Electric Guitar Amp
Active
D.I.
PA / Recording Console
Pure Magnetic Signal
(Tip)
Powerbridge™ Signal
(Ring)
Powerchip™
Mono Instrument Cable
F
®
Use Existing Inserts
and Pivot Screws
Drill 3/32"
(2.4 mm) Hole
from Vibrato Cavity
to Control Cavity
Magnetic
Volume
Sleeve
Ring
Tip
Magnetic
Signal
Stereo Jack
Optional 3-Way
Selector Switch
Mag
Both
Piezo
ON ONOFF
Powerbridge™
5Meg
Resistor
250K - 300K
Audio T aper Pot
Sleeve
Ring
Tip
1500 pF1500 pF
330 K820 pF
Magnetic Signal
Optional 3-Way
Selector Switch
Mag
Both
Piezo
O
N
O
F
F
O
N
Stereo
Output
Jack
ISHMAN
P
OWERBRIDGE
™ P
ICKUP
I
NSTALLATION
G
UIDE
Wiring Instructions
Passive Setup
• Active Setup - Powerchip
With our onboard Powerchip™, you can mix and combine both the Powerbridge™
and magnetic pickups (on the guitar) and plug right into a single channel guitar
amplifier. You can also instantly split signals by simply changing to a stereo cable or
stereo "Y" cable.
See the Powerbridge™ System Users Guide
for Powertronics™ descriptions.
™
Active Setup
Bridge Installation
FIG 1 - Existing Pivot Screws
If you have a Fender
American Standard
Strat®or Strat Plus
®
®
(knife-edge vibrato)
style guitar, the
Powerbridge™
Pickup is a direct
replacement.
See Fig. 1
• Instrument Builders
Refer to the enclosed Routing Template to locate the brass
inserts.
• Routing the Powerbridge™
Pickup Wire
•
With a 3/32” (2.4mm) aircraft bit, drill a hole from the vibrato
cavity to the control cavity.
•
Route the Powerbridge™ Pickup wire through this hole. See
Fig. 2
If you prefer, you may route the Powerbridge™ Pickup wire
through the guitar's ground wire channel. If you do so, secure
the Powerbridge™ Pickup wire so that it cannot be pinched by
the springs or the bridge block.
FIG 2 - Hole for Powerbridge™ Signal Wire
• Preliminary Notes
To prevent 60 Hz hum, the entire Powerbridge™ Pickup signal path should be fully shielded. The control cavity, jack cavity, and any non-conductive
surface to which the controls are mounted (such as a plastic pickguard) must be shielded with adhesive-backed foil or conductive paint. The
shielded cavities should then be grounded.
For complete hum prevention, the included stereo jack must also be shielded. To do this, we’ve included a piece of shielding foil. Note that one
side is insulated. After you have soldered the wires to the jack, roll the foil into a tube so that the insulation is on the INSIDE and surround the
stereo jack with the tube. Connect the foil side of the tube to ground by soldering it to the shielding of the Powerbridge™ Pickup wire or to a jumper
that is connected to any ground.
If your instrument has active magnetic pickups (requiring an onboard battery), you will need a special 9 Pin Switching Jack (Fishman Part Number
ACC-PBR-9PJ), available through your Fishman dealer.
• Install the Stereo Jack
The jack can fit into the jack cavity without removing wood ...
1 Bend the terminals of the included stereo jack toward its center.
See Fig 3
2 Rotate the jack to locate the Tip terminal exactly at the upper left side of
the jack plate recess.
See Fig 4
FIG 3 - Bend Jack Terminals FIG 4 - Align Tip Terminal
• Wiring Options
There are several different ways to wire the Powerbridge™.
Choose the option that best suits your needs.
Powerbridge™ & Magnetic Pickups
wired directly to a Stereo Jack
1. Connect the Powerbridge™ signal wire directly to the Ring terminal on the
supplied stereo jack.
2. Connect the Powerbridge™ and magnetic grounds to the Sleeve terminal.
3. Connect the magnetic signal wire to the Tip terminal.
4. Connect the included 5 M
Ω
resistor between the ring and sleeve terminals.
Passive Volume for the Powerbridge™
This circuit that is easily assembled from "stock" guitar pots and components
available at any electronics parts retailer.
Y
ou will need:
• 250 k audio taper pot
• 330 k resistor
• 820 pF capacitor
• 1500 pF capacitor
This network will attenuate the Powerbridge™ so that it better matches levels
between magnetic and piezo pickups. You can expect a 14 dB (nominal)
decrease in Powerbridge™ output with this circuit.
Direct Wiring
NOTE: Optional 3-Way Selector Switch -
If desired, a
single pole, double throw (spdt) 3-way switch can also be added for
piezo/magnetic pickup selection. Use a switch with an ON-OFF-ON
orientation (no, this is not a misprint)
NOTE: Active Onboard Blending
A Fishman Powerchip™ (not included) must be installed if you wish
to blend/mix piezo and magnetic signals onboard the instrument.
FISHMAN TRANSDUCERS
340-D Fordham Road Wilmington MA 01887 USA
Phone 978-988-9199 • Fax 978-988-0770
www.fishman.com
®
Passive Volume
Loading...