Fishman Fluence Stephen Carpenter Signature Install Manual

Installation
1. Plan an installation. We've included two potential wiring diagrams from Stephen and ESP Guitars. Additional diagrams are available at www.shman.com.
Stephen's personal diagram uses a standard 3-way selector to simultaneously switch pickups and voicing as follows: Position 1- Bridge Pickup, Voice 1. Position 2- Bridge pickup Voice 2. Position 3- Neck Pickup, Voice 2.
2. Test t the components to make sure that each will t in the allocated locations, or modify the instrument until the t is correct and all the controls can be located without issue.
4. Pickup Voicing and High Frequency Tilt (HF Tilt) are selected by connecting their leads to Ground. Stephen doesn't use HF Tilt (disconnected) in his diagram, and his pickup voicing is automatically selected at each of his three positions. However you can use these features, either switchable or xed, as indicated in our standard wiring diagram or by creating a custom plan with your installer.
5. Once your nal wiring diagram has been chosen and your parts are laid out, complete the soldering, mount and secure all your components and test your completed installation before assembly. Be sure the push connectors are plugged in the correct way and that the little arrow (triangle) imprinted onto the top left side of the connector matches the one on the connector. Then plug in and play!
Ceramic Bridge Pickup Peak Frequency:
Voice 1 - 750Hz Voice 2 - 1.4kHz
Alnico Neck Pickup Peak Frequency:
Voice 1 - 630Hz Voice 2 - 550Hz / 8kHz
Overview
These instructions provide installation options for the Fishman Fluence Stephen Carpenter signature pickups. This system includes controls required for a number of different install combinations. But these instructions are not comprehensive. A skilled electronics technician may interpret this overview to create a wider range of installation options.
Installation Warning!
By self-installing and/or misusing this product, you understand and agree that and such uses are high risk activities and, to the extent permitted by law, YOU EXPRESSLY AND VOLUN­TARILY ASSUME THE RISK OF DEATH OR OTHER PERSONAL INJURY SUSTAINED WHILE PARTICIPATING IN SUCH ACTIVITIES WHETHER OR NOT CAUSED BY THE NEGLIGENCE OR ANY OTHER FAULT of Fishman, including but not limited to equipment malfunction from whatever cause, or any other fault of Fishman. Additionally, you agree to indemnify, defend and hold Fishman harmless from any third party claims arising from such activities.
INSTALL GUIDE
STEPHEN CARPENTER
SIGNATURE 7 & 8 STRING
HUMBUCKER SET
514-300-139 r1 7/16
"ESP" is a registered trademark of the ESP Guitar Company.
COIL
TAPS
H
CT
+9-18V
GND
GND
HF Tilt
GND
Voice 2
OUTPUT
V1 Gain
GND
STEPHEN CARPENTER
Signature Series
7 & 8 STRING CERAMIC
COIL
TAPS
H
CT
+9-18V
GND
GND
HF Tilt
GND
Voice 2
OUTPUT
V1 Gain
GND
STEPHEN CARPENTER
Signature Series
7 & 8 STRING ALNICO
ilt
Bridge Pickup: Modern Ceramic
Neck Pickup: Modern Alnico
.22uF
Output Jack
9V Battery
Ring
Tip
Sleeve
Bridge Ground
(-)
(+)
Pull Voice-2
25k
25k
Vol.
Tone
High Frequency Tilt Wires (for darker tone)
- Connect to ground to activate.
- Insulate if not used.
- Can be wired to a switch.
- Blue & Yellow can share the same switch contact.
CC NN BB M M
Neck Pickup
Bridge Pickup
Both
Neck Wire
Bridge Wire
Stephen Carpenter Signature 7 & 8 String Pickup Set ESP Preferred Wiring Diagram 1 x Volume, 1 x Tone Volume: Pull Voice - 2 for both pickups Blade style pickup selector
COIL
TAPS
H
CT
+9-18V
GND
GND
HF Tilt
GND
Voice 2
OUTPUT
V1 Gain
GND
COIL
TAPS
H
CT
+9-18V
GND
GND
HF Tilt
GND
Voice 2
OUTPUT
V1 Gain
GND
STEPHEN CARPENTER
Signature Series
7 & 8 STRING ALNICO
STEPHEN CARPENTER
Signature Series
7 & 8 STRING CERAMIC
.22uF
25k
25k
Bridge Pickup: Stephen Carpenter
Signature Series
Neck Pickup: Stephen Carpenter
Signature Series
9V Battery
(–)
(+)
1
2
Neck Pickup Voice 2
Bridge Pickup Voice 1
Bridge
Pickup Voice 2
Pickup Selector
3-way Switch
Output Jack
Jumper
Ring
Sleeve
Tip
Bridge Ground
Stephen Carpenter Signature 7 & 8 String Pickup Set Stephen Carpenter Preferred Wiring Diagram Use 3-way selector for voice switching
Pickup Selector 3-way Switch
Note: “V1 Gain” (shown not used) Ground or jumper for Voice 1 Low Gain setting
CC NN BB M M
CAUTION! Excessive pressure may puncture the battery. Isolate all components during installation to eliminate shorting or risk of re.
CAUTION! Excessive pressure may puncture the battery. Isolate all components during installation to eliminate shorting or risk of re.
shman.com
Loading...