Fisher-Price X0465 Instruction Sheet

Track Layout

NOTE: Adults should remove & discard rubber bands holding tracks together.

BATTERY INSTALLATION

Unscrew and lift away cover from top of product. Replace batteries as indicated inside the battery compartment.
Batteries included are for demonstration purposes only. For longer life use only alkaline batteries. Requires 3 "AAA" (LR03) Batteries.
If this toy begins to operate erratically, you may need to reset the electronics. Remove the batteries from the toy and replace it.

BATTERY SAFETY INFORMATION

In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your toy (product). To avoid battery
leakage:

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the product before being charged (if designed to be removable).

• Rechargeable batteries are only to be charged under adult supervision (if designed to be removable).

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

• Do not mix old and new batteries.

• Only batteries of the same or equivalent type as recommended are to be used.

• Batteries are to be inserted with the correct polarity.

• Exhausted batteries are to be removed from the product.

• The supply terminals are not to be short-circuited.

• Dispose of battery(ies) safely.

• Do not dispose of this product in a fire. The batteries inside may explode or leak.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for

help.NOTE: Changes or modifications not expressively approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

• THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

• CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A LA NORME NMB-003 DU CANADA.

• Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

• L’utilisation de ce produit est sujette aux conditions suivantes :

(1) il ne doit pas produire de brouillage et (2) il doit pouvoir tolérer tout brouillage reçu, même si ce brouillage est susceptible de compromettre son fonctionnement.

Required tool:

Phillips screwdriver

(not included)

Thomas

1,5V x 3

“AAA” (LR03)

ON/OFF

OFF ON

Switch

NOTE:

When switch is ON the
engine will move around
the track and phrases will
automatically play every
10 seconds.

INSTRUCTIONS

Please keep these instructions for future reference as they contain important information.

Assembly

1. Assemble the bridge by attaching
the sides of the bridge to the base.
Attach the track pieces to the water
piece and then attach the
drawbridge to the track
pieces as shown.

2. Attach the assembled drawbridge to the track layout.

How To Play

1. Set the brake lever to the STOP position. As the engine approaches, the brake switch will stop
the engine in front of the drawbridge. While the engine is stopped in front of the drawbridge,
the wheels of the engine will power the drawbridge to rise.

While the engine is stopped in front of the drawbridge, the wheels of the engine will power
the drawbridge to rise.

STO P

Item No : X0465-0920
Version : EL
Size : 16.54" x 11.69" (A4)
Paper : Woodfree paper 80 gsm
Color : Black
Date : May. 26, 2011 (BC)

Based on the Railway Series by The Reverend W Awdry. © 2011 Gullane (Thomas) Limited.
Thomas the Tank Engine & Friends and Thomas & Friends are trademarks of Gullane (Thomas) Limited.
© HIT Entertainment Limited. HIT and the HIT logo
are trademarks of HIT Entertainment Limited.
Fisher-Price, Inc., a subsidiary of Mattel, Inc.,
East Aurora, NY 14052, U.S.A.
PRINTED IN CHINA. Manufactured for Fisher-Price.
© 2011 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.,

unless otherwise indicated.

Mattel East Asia Ltd., Room 1106, South Tower,

World Finance Centre, Harbour City, Tsimshatsui, HK, China.

Protect the environment by not disposing
of this product with household waste
(2002/96/EC). Check your local authority for
recycling advice and facilities.

X0465

ID.X0465-0920

2. Set the brake lever to the GO position to lower the drawbridge
and send the engine on its way over the bridge.

NOTE: Do not touch the moving drawbridge while the engine is powering it.

ADULT ASSEMBLY REQUIRED.

No tools required for assembly.

GO