Page 1
www.fisher-price.com
Page 2
Consumer Information
WARNING
Possible Entanglement Injury
• Keep out of baby’s reach.
• Remove mobile from crib/cot or playpen when
baby begins to push up on hands or knees.
• This product will not attach to all crib/cot
designs. Do not add additional strings or
straps to attach to crib/cot or playpen.
CAUTION
This toy contains small parts in its unassembled
state. Adult assembly is required.
• Please keep this instruction sheet for future reference,
as it contains important information.
• Adult assembly is required.
• Requires four “D” (LR20) alkaline batteries for the mobile
and two “AA” (LR6) alkaline batteries for the remote.
(Batteries not included.)
•
Tool required for assembly: Phillips screwdriver (not included).
• Age: Birth to 5 months.
• A crib/cot mobile is intended for visual stimulation and is
not to be grasped by a child.
• When used on a dresser top, do not place within the
reach of a standing baby.
• Always attach by all provided fasteners (clamp) tightly to
a crib/cot or playpen according to the instructions.
Check frequently.
Remote
Arm
Parts
Base
3 Spokes
3 Soft Toys
3 Hangers
Crib/Cot Adapter
Clamp
Hub
#6 x 1.6 cm Screw – 1
#4 x 1 cm Washer Head Screw – 3
Both Shown Actual Size
Note: Tighten and loosen the screws
with a Phillips screwdriver. Do not
over-tighten the screws.
PRINTED IN CHINA M6162pr-0920
2
Fabric Skirt
Page 3
Battery Installation
1.5V x 2
“AA” (LR6)
1.5V x 4
“D” (LR20)
We recommend using alkaline
batteries for longer battery life.
Remote
• Loosen the screw in the battery compartment door
with a Phillips screwdriver. Remove the battery
compartment door.
• Insert two “AA” (LR6) alkaline batteries, as indicated
inside the battery compartment.
• Replace the battery compartment door and tighten the
screw with a Phillips screwdriver. Do not over-tighten.
IMPORTANT! If the mobile does not respond to the remote,
it does not mean that the battery power in the remote is
low. Replace the batteries in the remote if the LED signal
indicator on the remote is dim when the button is pressed.
If the LED signal indicator does not light after installing
new batteries in the remote, check the orientation of the
batteries in the battery compartment to make sure they
are properly installed.
Protect the environment by not disposing of this
product with household waste (2002/96/EC). Check
your local authority for recycling advice and facilities.
Mobile Base
• Loosen the screws in the battery compartment door
with a Phillips screwdriver. Remove the battery
compartment door. You may need to use the tip of the
screwdriver to lift the battery compartment door.
Hint: If the crib/cot adapter is attached to the base, loosen
the screws in the crib/cot adapter and remove it first.
• Insert four “D” (LR20) alkaline batteries.
• Replace the battery compartment door and tighten the
screws with a Phillips screwdriver. Do not over-tighten.
IMPORTANT! Under normal use conditions, the batteries
in the mobile will require replacement more often than the
batteries in the remote. When sounds or light become faint
or movement of the mobile is sluggish, it’s time for an adult
to replace the batteries in the mobile base.
3
Page 4
Battery Safety Information
FCC Statement
In exceptional circumstances batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery
compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Care
Soft Toys and Fabric Skirt
• To remove a soft toy, slide the string out of the slot in
the hanger.
• The soft toys and fabric skirt are surface washable.
Mobile
Wipe with a clean cloth dampened with a mild soap
and water solution. Do not immerse. The mobile has no
consumer serviceable parts. Do not take the mobile apart.
United States Only
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
inter-ference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void the
user's authority to operate the equipment.
• This device complies with Part 15 of the FCC Rules.
• Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
4
Page 5
Assembly
1
• Insert and "snap" the ends of the spokes into the slots in
the hub, as shown.
Spoke
Hub
Slot
3
Slot
Soft Toy String
• Fit a soft toy string into the slot in the end of a hanger.
• Pull down gently on the soft toy to secure the string in
the hanger.
• Repeat this procedure to attach the remaining soft toys to
the other two hangers.
4
Hub
Hanger
Arm
2
Hanger
• Fit the end of a hanger into a hole in the hub.
• Insert a #4 x 1 cm screw into the hanger and tighten.
• Repeat this procedure to attach the other hangers.
• Insert and “snap” the arm into the hole in the side of
the hub.
5
Page 6
Assembly
Crib/Cot Setup
5
Arm
Base
• Fit the other end of the arm into the slot in the base, as
shown.
• Insert the #6 x 1.6 cm screw into the arm and tighten.
1
• Position the base so that the battery compartment door
is facing you.
• Fit the crib/cot adapter onto the base.
Crib/Cot Adapter
Battery
Compartment
Door
6
• Place the fabric skirt on top of the mobile hangers
and spokes.
• Fasten the fasteners on the fabric skirt.
2
Tighten Screws
• Tighten the four screws in the crib/cot adapter.
6
Page 7
Crib/Cot Setup
Dresser Top Setup
3
Crib/Cot
Top Rail
Base
Threaded Peg
7"
Clamp
• Fit the mobile base on to the crib/cot top rail so that the
threaded peg extends outside of the crib/cot.
• Fit the clamp onto the threaded peg and turn the clamp
clockwise to secure the base to the crib/cot rail. Do not
over-tighten the clamp.
• If the distance between the mobile and the mattress is
less than 7 inches, lower the crib mattress.
1
Loosen Screws
• Loosen the screws in the crib/cot adapter.
• Lift and remove the crib/cot adapter.
• Store the crib/cot adapter in a safe place for future
crib/cot use.
Crib/Cot Adapter
Battery Compartment Door
2
Knob
• Pull the knob on the arm out.
• Rotate the mobile portion of the arm down.
• Release the knob to lock the arm in position.
• Place the mobile on a dresser top out of reach of baby.
7
Page 8
Use
IMPORTANT!
• In the unlikely event that use of the remote interferes with
normal use of other remote controlled equipment, such as
televisions and stereos, or use of other electric or battery
powered appliances interfere with operation of the mobile,
do not use both appliances at the same time.
• For best performance between the mobile and the remote,
avoid using the remote in areas of bright light. In bright
natural or artificial light, you may notice loss of range.
Move the mobile or otherwise reduce the amount of light
to improve performance.
Mobile Dome
Power/Volume Switch
• Slide this switch to on with low
volume ; on with high volume ;
on with no sound (lights only)
or off .
Song Select Button
• Press this button to choose a song.
• Each time you press the song select
button the mobile will switch to the
next song until it returns back again
to the first.
Light Select Button
• Press the button to choose from four
different light modes:
1 Twinkling lights around baby's room
2 Glowing night light
3 Twinkling and glowing lights
4 No lights (music only)
• Each time you press the light select
button the mobile will switch to the
next of the four modes until it returns
back again to the first.
;
• When using the remote, make sure that the arrow on the
mobile’s dome is pointing towards the transmitter window
on the remote. For best results make sure the path
between the transmitter window on the remote and
the dome on the mobile are in a direct line and free of
obstacles. Rotate the mobile dome so that the arrow
points to the area from which you’re most likely to
use the remote. For example, if you’ll most often be using
the remote from the doorway of the nursery, make sure
that the arrow on the mobile dome is pointing towards the
doorway and that the path between the mobile dome and
the doorway is free from obstructions.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Start Button
Remote
Start Button
• Press the start button to activate
the mobile.
• The mobile will play for about
10 minutes.
• To restart or pause the mobile, press
the start button on the remote control
or the start button on the mobile.
Notes:
- The remote control will activate the
mobile from one foot to as far as
20 feet away.
- After approximately two hours
without activation, the mobile shuts
down. Turn the Power/volume switch
to off and then on to restart the
mobile and reactivate the start button
and the remote.
8
Loading...