• This vehicle requires adult assembly. Please set aside
at least 30 minutes for assembly.
• Read this manual carefully for important safety
information and operating instructions before using
this vehicle. Keep these instructions for future reference,
as they contain important information.
• This vehicle is designed for use: on asphalt or other
hard surfaces; on generally level terrain and by children
12 to 36 months of age.
• To prevent damaging the motors, do not tow anything
behind the vehicle or overload it. Do not exceed the
maximum weight capacity of 40 lbs (18 kg).
• If you have any questions about your Power Wheels
vehicle, please call our toll-free service lines at
1-800-348-0751 from 8 AM to 6 PM (EST) Monday
through Friday. Trained customer service representatives are available to take your call in English or
French. Habla Español? Si usted tiene alguna pregunta
ó necesita asistencia llame gratis 1-800-348-0755 para
los Estados Unidos. Tenemos representantes que
hablan español para atender su llamada.
• For your convenience, Power Wheels maintains an
Authorized Service Center Network with more than 400
authorized service centers nationwide. Our authorized
service centers will repair or replace parts under warranty at no extra charge, and can perform non-warranty
repairs for a minimal charge. Please see the Authorized
Service Center list beginning on page 16 to find the
authorized service center nearest to you, or call
1-800-348-0751.
• Please complete and return the enclosed Registration
Card today, or call 1-800-348-0751 to register your
vehicle by phone.
• Make sure children know and follow these rules for safe
driving and riding: always sit on the seat; always wear
shoes; only 1 (one) rider at a time.
Important Information
®
B
Warnings
WARNING
•Prevent Injuries and Deaths
• Direct Adult Supervision Required
• Keep Children Within Safe Riding Areas.
These areas must be:
- away from swimming pools and other
bodies of water to prevent drownings
- generally level to prevent tipovers
- away from steps, driveways, roads
and alleys.
• Not to be used by children over 36
months, to prevent overloading.
2
C
• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return
this product to the store.
• Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no
parts are discarded.
• Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to
remove any excess lubricant.
Parts
Sport Bar
Handlebar
Foot Peg Assembly
Vehicle Body
Motor Assembly
Rear Axle
Support
Steering Linkage
Wheel - 4
Seat
Front Axle
Rear Axle
3
Microphone
Parts
Key Assembly
Rectangular Bushing
with Extension - 4
Rectangular
Bushing - 4
Not Shown: Label Sheet
#8 x 7/8" Trusshead Screw - 2
#8 x 5/8" Trusshead Shoulder Screw - 2
Round Bushing - 4
#8 x 3/4" Screw - 4
Round Washer - 2
Washer Plate - 2
#8 x 11/4" Screw
.354 Cap Nut - 4
All Shown Actual Size
4
D
Parts Diagram
3
5
1
4
14
21
15
6
8
22
7
2
13
16
18
11
17
23
Note: Some parts shown are assembled to both sides of the vehicle.
22
13
10
20
20
9
19
9
12
16
18
11
17
23
1. Vehicle Body
2. Front Axle
3. Seat
4. Motor Assembly
5. Handlebar
6. Sport Bar
7. Foot Peg Assembly
8. Rear Axle Support
9. Washer Plate - 2
10. Steering Linkage
11. Wheel - 4
12. Rear Axle
13. Round Washer - 2
14. Key Assembly
15. Microphone
16. Rectangular Bushing
with Extension - 4
5
17. Round Bushing - 4
18. Rectangular Bushing - 4
19. #8 x 7/8" Trusshead Screw - 2
20. #8 x 5/8" Trusshead Shoulder Screw - 2
21. #8 x 11/4" Screw
22. #8 x 3/4" Screw - 4
23. .354 Cap Nut - 4
Not Shown
Label Sheet
E
Assembly
CAUTION
This product contains small parts in its
unassembled state. Adult assembly is required.
1
Opening
Motor Assembly
Motor Connector
• Align the slot in the handlebar's power button connector
with the tab on the motor connector and push firmly to
plug the two connectors together. Make sure the two
connectors are fully engaged.
• Fit the connectors neatly into the opening.
• Fit the handlebar stem in the hole in the vehicle body.
Make sure the horn on the handlebar faces the rear
of the vehicle body.
1
• Insert a #8 x 1
assembly.
Note: You may need to rotate the motor assembly
slightly to align the holes.
• Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
/
4" screw through the hole in the motor
3
Vehicle
Body
Bottom View
• Position the vehicle body upside down on a flat surface.
• Fit the motor assembly into the opening towards the
front of the vehicle body. Make sure the motor connector
extends through the opening.
Horn
Slot
Tab
2
Handlebar
Power
Button
Connector
Power Button Connector
Motor Connector
Motor
Connector
Sport Bar
"Spare Tire"
Back View
• Position the sport bar over the vehicle body so that it
angles towards the rear of the vehicle.
• Fit the ends of the sport bar into the holes to the sides
of the "spare tire".
• Push firmly on each side of the sport bar to snap the
ends into the vehicle body.
Hint: You may need to rock the sport bar back and forth
while pushing it into the vehicle body.
Motor
Assembly
• Hold the motor assembly in place and postion the
vehicle body upright.
Side
View
6
Assembly
4
Rear Axle
Support
Hole
Screw
Peg
Bottom View
• Position the vehicle body upside down.
• With the cupped side of the rear axle support facing up,
fit the holes in the rear axle support onto the screw pegs
on the vehicle body.
Hole
Screw
Peg
5
Metal
Washer
Plate
Metal
Washer
Plate
6
Washer
Screw
Peg
Rear Axle
Support
Bottom View
• Insert #8 x 5/
holes in the steering linkage.
• Fit a round washer on the end of each screw.
• Insert one of the screws (with washer) into the screw
peg on the rear axle support. Insert the other screw
(with washer) into the hole in the motor assembly.
• Tighten the screws with a Phillips screwdriver but do
not over-tighten. It is important that the screws not
restrict movement of the steering linkage.
8" trusshead shoulder screws through the
Motor
Assembly
Washer
Steering
Linkage
Screw
Peg
Rear
Axle
Support
• Fit the two metal washer plates onto the vehicle body
screw pegs extending through the rear axle support.
• Insert a #8 x 7/
washer plate and into the vehicle body.
• Tighten the screws with a Phillips screwdriver but do not
over-tighten. It is important that the metal washer
plates move freely under the screws.
Bottom View
8" trusshead screw through each metal
Screw
Peg
7
7
Rear Axle
Support
Assembly
• Slide a round bushing into the center of the wheel.
• Press the round bushing (barrel side first) onto the
rear axle.
• Fit a cap nut on the end of the rear axle. While
supporting the opposite end of the rear axle, tap the
cap nut with a hammer to secure it on the end of the
rear axle.
• Pull on the wheel to make sure the cap nut is secure.
Rear
Axle
• Repeat this procedure to assemble a wheel on the
other side of the rear axle.
Channel
Bottom View
• Slide the rear axle into the channel in the rear
axle support.
Note: The rear axle is smooth; the front axle has tabs.
• Center the rear axle in the channel.
8
Rectangular
Bushing with
Side
Rib
Extension
Rectangular
Bushing
Round
Bushing
Cap
Nut
Motor
9
• Slide the front axle through the square openings in the
motor assembly.
Note: You may need to rotate the front axle to fit the
tabs on the axle through the keyhole opening on the
inside of the motor assembly.
• Center the front axle in the motor assembly.
Assembly
Square
Opening
Bottom View
Front Axle
Tabs
Rear
Side
Rib
• Slide a rectangular bushing with extension (bushing
side first) onto one end of the rear axle.
• Fit the bushing between the two side ribs on the
rear axle support.
• Slide a rectangular bushing (without extension) onto
the rear axle.
• Slide a wheel ("hubcap" side out) onto the rear axle.
Axle
Wheel
Bottom View
8
Assembly
Square
10
• Slide a rectangular bushing with extension (bushing
side first) onto one end of the front axle.
• Press the bushing into the square opening on the
motor assembly.
• Slide a rectangular bushing (without extension) onto
the front axle.
• Slide a wheel ("hubcap" side out) onto the front axle.
• Slide a round bushing (barrel side first) onto the
front axle.
• Press the round bushing into the center of the wheel.
• Fit a cap nut on the end of the front axle. While
supporting the opposite end of the front axle, tap the
cap nut with a hammer to secure it on the end of the
front axle.
• Pull on the wheel to make sure the cap nut is secure.
• Repeat this procedure to assemble a wheel on the
other side of the front axle.
Opening
Rectangular
Bushing with
Extension
Rectangular
Bushing
Bottom View
Round
Bushing
Cap
Nut
Wheel
Foot Peg
11
Screw
Pegs
Guide
Ribs
Rear
Wheel
• Turn the foot peg support upside down (flat side up)
and position it over the center of the vehicle body so
that the side with the curved arch faces toward the
rear wheels.
• Align the four screw pegs on the foot peg support with
the four screw pegs on the vehicle body. Make sure
that the bottom edge of the foot support fits into
the two sets of guide ribs on the vehicle body.
• Insert four #8 x 3/4" screws through the screw pegs and
into the vehicle body. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
Support
Curved
Arch
Screw
Pegs
Guide
Ribs
Rear
Wheel
Bottom View
9
Assembly
2
1
1
2
12
Hole
Left
Peg
• Position the vehicle body upright.
• Fit the peg on the left side of the seat into the hole in
the left side of the vehicle body .
• Push firmly near the peg on the right side of the seat
to snap it into the hole in the right side of the vehicle
body .
Hole
Right
Peg
13
Microphone
Microphone
Cord
• Fit the key assembly into the large hole below
the handlebar.
• Bend the end of the microphone cord so that the tip
forms a "T".
• Fit the end of the microphone cord into the small hole
below the handlebar. Pull up gently on the microphone
cord to make sure it is secure.
• Fit the tab on the back of the microphone into the notch
on the side of the vehicle body.
Notch
Key
Assembly
One-time assembly is now complete.
10
F
Proper label application will help to keep the labels
looking their best!
• Wash your hands before applying the labels.
• Make sure the areas where the labels will be applied
are clean and dry. Wipe your vehicle with a clean, soft,
dry cloth to remove any dust or oils.
• For best results, avoid repositioning a label once it has
been applied to the vehicle.
• Apply the labels as shown in the illustrations.
• After applying each label, rub the label firmly with a
clean, dry cloth to make sure the label is adhered
to your vehicle.
Label Decoration
10
5
5
3
4
8
8
10
5
6
1
1
2
Left Side View
6
1
7
9
Back View
7
2
4
11
1
2
2
Right Side View
TOP
G
TOP
TOP
1.5V x 6
-
This vehicle requires six "D" (LR20) alkaline
batteries (not included) for motorized use.
SHOWN ACTUAL SIZE
"D" (LR20)
1
Battery Installation
3
PUSH
HERE
+
Tabs
Slots
Battery
Compartment
Door
Battery Compartment Cover
PUSH
HERE
Slots
PUSH
HERE
Front
Wheels
• Stand the vehicle body up on its back end.
• Loosen the screws in the battery compartment door
with a Phillips screwdriver. The screws will remain in
the door.
• Push in on the sides of the battery compartment cover
near the bottom and lift to remove the cover.
2
PUSH
HERE
Battery
Compartment
• Fit the battery compartment cover over the batteries.
Make sure that the TOP of the cover is at the top and
that the four tabs on the sides of the cover are aligned
with the slots in the base of the motor assembly.
Battery
4
Compartment
Cover
PUSH
HERE
• Insert six "D" (LR20) alkaline batteries as indicated in
the battery compartment.
• Apply light pressure to the battery compartment
cover and tighten the screws with a Phillips screwdriver.
Do not over-tighten.
12
Battery Installation
Rules For Safe Driving
Battery Tips
• Be sure to insert the batteries correctly and always
follow the toy and battery manufacturer's instructions.
• Do not mix old and new batteries.
• Do not mix different types of batteries:
alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Remove the batteries during long periods of non-use.
Always remove exhausted batteries from the product.
Battery leakage and corrosion can cause damage.
Dispose of batteries properly.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as
recommended in the “Battery Installation” instructions
are to be used.
• If removable rechargeable batteries are used, they are
only to be charged under adult supervision.
• Rechargeable batteries are to be removed from the
product before they are charged.
• If you use a battery charger, it should be examined
regularly for damage to the cord, plug, enclosure and
other parts. Do not use a damaged battery charger until
it has been properly repaired.
• If this vehicle drives sluggishly or will not drive at all, it's
time to replace the batteries.
Rules For
H
Safe Driving
WARNING
Prevent Injuries and Deaths
• Direct Adult Supervision Required.
• Keep Children Within Safe Riding Areas
These areas must be:
- away from swimming pools and other
bodies of water to prevent drownings.
- generally level to prevent tipovers.
- away from steps, driveways, roads
and alleys.
• Not to be used by children over 36
months, to prevent overloading.
Teach Safety Rules to Children
While children can quickly develop the skill necessary to drive this
vehicle, it is important to remember that their judgment skills are still
very immature. Unsupervised driving by children can lead to serious
injury. Before children use this vehicle, an adult should carefully
evaluate the driving area as well as the children’s skill level and ability
to drive this vehicle safely. Children are not always able to recognize
or anticipate hazards, even when they have been taught about them.
THERE IS NO ACCEPTABLE SUBSTITUTE FOR DIRECT
ADULT SUPERVISION.
Teach appropriate safety rules to your child before allowing
operation of this vehicle. These rules should also be reviewed
with neighborhood children or other playmates who want to drive
this vehicle.
Riding Rules
Make sure children know and follow these rules for
safe driving:
1. Always sit on the seat.
2. Always wear shoes.
3. Only 1 (one) rider at a time. A child who is not sitting on the seat
or who is standing on the vehicle could fall off, cause a tip-over
or block the driver’s view. A child could be seriously injured.
4. Do not allow any child to drive the vehicle in the street or near
moving (motorized) vehicles.
5. Do not allow any child to drive near bodies of water (such as
pools or creeks), obstructions (such as furniture, low tree limbs
or play equipment), or drop-offs (such as stairs or decks).
6. Do not allow any child to drive the vehicle in the dark. A child
could encounter unexpected obstacles and have an accident.
Operate the vehicle only in the daytime or a well-lit area.
7. Do not allow your child to drive on sloped or inclined surfaces.
Restrict your child’s driving to generally level
ground ONLY!
8. Do not allow your child to drive down or across a
steep slope.
- The vehicle may gain unsafe speed, even if the pedal is
released to stop.
- The vehicle may tilt and tip over.
- The wheels could lose traction, causing the vehicle to slip.
9. Do not allow your child to drive up steep inclines. The
motor may stop and the vehicle could roll backwards at an
unsafe speed.
10. Never put anything near any moving parts. Rotating parts such
as motors, gear boxes and wheels can snag fingers, hair, etc.,
causing serious injury. Do not allow operation of the vehicle
when it is on its side or in an upside-down position.
11. Do not operate the vehicle near flammable vapors (gasoline,
paint thinner, acetone, liquid wax, etc.). The vehicle’s electrical
switches, like most electrical switches, emit an internal spark
when first turned on or turned off. The presence of flammable
liquids or vapors could cause an explosion or a fire. Keep all
flammable products in tightly sealed containers and away from
the vehicle.
12. Do not allow a child to operate the vehicle without direct adult
supervision. To prevent unsupervised use of the vehicle,
disconnect the motor harness from the battery when the vehicle
is not in use.
13
I
This vehicle has been designed for use as a foot powered ride-on for younger children and for use as a battery powered,
motorized vehicle when your child is ready to roll.
How to Operate Your Vehicle
Foot
Peg IN
Foot Power
Foot
Peg IN
Foot Peg
OUT
Motorized
Foot Peg
OUT
• For use as a foot powered ride-on, make sure the foot
pegs are pushed into the foot peg support.
• For use as a battery powered motorized vehicle,
pull the foot pegs out to extend them to the
platform position.
• Make sure your child's feet are resting on the foot
pegs and press the handlebar button. The vehicle
will move forward at a maximum of 1 mph.
14
J
Caring for
Your Vehicle
K
Bumper-to-Bumper*
Limited Warranty
• Check all screws, cap nuts and protective coverings
regularly and tighten as required. Check plastic parts on
a regular basis for cracks or broken pieces.
• During snowy or rainy weather, the vehicle should be
stored inside or under a protective cover.
• Avoid operating the vehicle in wet or snowy conditions
and do not spray the vehicle with a hose. Do not wash
the vehicle with soap and water. Water or moisture in
the motor can cause it to corrode and could cause
motor failure.
• Avoid operating the vehicle on sand, loose dirt or
gravel. Sand, loose dirt or gravel in the motor can cause
it to jam and could cause motor failure.
• The vehicle can be wiped down with a soft, dry cloth.
For a shiny finish, you can wipe plastic parts with a nonwax furniture polish applied to a soft-cloth. Do not use
automotive wax. Do not use soap and water or spray
the vehicle with a hose.
*One year limited warranty from the date of
purchase on the Power Wheels
For the original purchaser, this one year limited warranty
covers the Power Wheels®ride-on vehicle (purchased
from Power Wheels®) against defects in materials and
workmanship.
This warranty covers normal use and does not cover the
Power Wheels®vehicle if damaged by unreasonable use,
neglect, accident, abuse, misuse, improper service or
other causes not arising out of defects in materials or
workmanship. Evidence of any attempt at consumer repair
will void this warranty. This warranty does not cover, and
is intended to exclude, any liability on the part of Power
Wheels®, whether under this warranty or implied by law or
any indirect or consequential damages for breach of
warranty. Some states do not allow the exclusion or
limitation so this limitation may not apply to you.
Should you need service or assistance with your vehicle
during the warranty period, do not return the vehicle tothe store. Power Wheels®has provided a nationwide
network of authorized service centers. Please refer to the
list in this manual. Power Wheels®is continually expanding
our Authorized Service Center Network. If there is not an
authorized service center in your area, please call
Consumer Relations for information, 1-800-348-0751.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE.
PLEASE SAVE YOUR ORIGINAL SALES RECEIPT.
®
vehicle.
15
L
Authorized Service Centers
We are continually expanding our Authorized Service Center Network. Please check this
listing for the Authorized Service Center nearest you. If there is not one in your area, please
call Power Wheels®Consumer Relations at 1-800-348-0751.