73528
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Age: 1½ years - 5 years.
Weight Limit: 50 lbs. (23 kg).
Tools needed for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (all not included).
1
www.fisher-price.com
Consumer Information
WARNING
To avoid serious injury:
• Adult supervision is required.
• Never use near cars and other motor vehicles,
near streets, steps, sloped driveways, hills,
roadways, alleys, swimming pool areas or
other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one (1) rider.
Fasteners
Cap Nut – 1*
*Note: For your convenience, an
extra cap nut is included.
#8 x 3/4" Screw - 13
#10 x 3/4" Screw - 11
#8 x 3" Screw – 1
Note: Tighten and loosen the screws with a Phillips
screwdriver. Do not over-tighten the screws.
All SHOWN ACTUAL SIZE
2
Note: The base/handle assembly
can be attached to the trike in
either the Ride-on Rocker (page 9)
or Learn to Pedal (page 10) mode.
Parts not shown: Assembly
Tool and Label.
Parts
Seat Pin
Seat
Handlebar
Frame
Fork
Frame Cover
Footrest
2 Fork Covers
Handle Bottom
Handle Pin
2 Base/Handle Covers
Straight Axle
2 Rear Wheels
Cap Nuts
2 Wheel Caps
Base
Front Wheel
Assembly
4 Pedal Axle Covers
Handle Top
3
Assembly
CAUTION
This product contains small parts in its
unassembled state. Adult assembly is required.
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry, cloth before
assembling this product.
Wheel
Cap
Rear Wheel
Hole
Frame
Hole
Straight Axle
Rear Wheel
Spoke Side Down
1
• Slide a rear wheel (spoke side down) onto the straight axle.
2
• Turn the frame upside down.
• Insert the straight axle assembly through the holes in the
rear of the frame.
• Fit the wheel cap into the center of the wheel. Tap the
wheel cap with a hammer to secure it to the wheel.
Straight Axle
Bottom View
4
Assembly
Rear Wheel
Spoke Side Up
Straight Axle
Assembled
Rear Wheel
3
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the assembled rear wheel on the scrap block
of wood.
• Slide the other rear wheel (spoke side up) onto the end
of the straight axle.
• Place a cap nut on the end of the straight axle.
• Place the assembly tool over the cap nut and tap it with
a hammer. Gently pull the rear wheel up to be sure
the cap nut is securely attached to the straight axle.
Assembly Tool
Cap Nut
Scrap Block
of Wood
Wheel Cap
4
• Fit the wheel cap into the center of the wheel. Tap the
wheel cap with a hammer to secure it to the wheel.
• Set the frame assembly aside.
Pedal Axle
Cover
Pedal Axle
Slot
5
Metal Tab
• Fit two pedal axle covers onto the pedal axle metal tabs.
Make sure the metal tabs fit into the slot in each pedal
axle cover.
• While holding the pedal axle covers on the pedal axle,
insert the pedal axle into the hole in the center of the
front wheel.
• Push the pedal axle covers into the center of the front
wheel until they are flush with the surface of the
front wheel.
• Repeat this procedure with the other two pedal axle
covers on the other side of the front wheel assembly.
Pedal Axle
Cover
5
Assembly
Front Wheel Assembly
Fork Cover
Fork Arms
6
Pedal Axle
• Place the front wheel assembly between the fork arms
so that the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #10 x ¾" screws into the fork cover
and tighten.
• Repeat this procedure to attach the other fork cover to
the other fork arm, using the #10 x ¾" screws.
Groove
Handlebar
Frame Neck
Fork Post
Fork Covers
FIRST, insert the screw
so that
THEN, tighten the screw.
¾
"
"
¾
is visible.
7
• Turn the frame upright.
• Insert the fork post up through
the hole in the frame neck. Make sure the fork is
positioned so that the fork covers face the rear wheels.
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post so that part of the screw (about
is still visible
. Tighten the screw.
¾")
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052, U.S.A.
©2008 Mattel, Inc. All Rights Reserved. ® and TM designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO 73528c-0920
6
Assembly
Knobbed End
Frame Opening
Footrest
Knobbed End
8
➥
➥
2
1
Footrest
3
➥
• Insert the knobbed end of the footrest up through the opening in the
underside, center of the frame .
• Rotate the footrest ¼ turn .
• Slide the footrest toward the
handlebar as far as it will go until
the top of the footrest is
positioned over the opening’s rectangular cut-out.
• Lower the knobbed end of the footrest into the rectangular
cut-out in the frame .
Frame Cover
3
1
2
Top View
Seat
Seat Mount
10
Seat Mount Adjustment Holes
• Place the seat on the seat mount.
• Adjust the seat for your child’s comfort by aligning the hole
in the seat with one of the seat mount adjustment holes.
9
•
Place the frame cover over the frame opening. Make
sure the holes in the frame cover align with the holes
on the frame.
• Insert three #10 x ¾" screws into the frame cover
and tighten.
7
Assembly
11
• While pushing down on the seat, insert the seat pin
through the hole in the seat and into a seat mount
adjustment hole.
Seat Pin
Handle Top
Handle Bottom
12
Base
13
• Insert 13 - #8 x ¾" screws into the handle top
and tighten.
Grooves
14
Wheel
Retainers
Base/Handle
• Fit the handle top and bottom to the end of the base,
as shown.
• Place the base/handle assembly on a flat surface so that
the wheel retainers are upright.
• Fit the trike onto the base/handle assembly so that the
rear frame rests in the grooves in the base and the front
wheel fits between the wheel retainers in the base/handle.
8
Assembly
Flared End
Handle
Cover
Trike
15
Base/Handle
• Position the base/handle covers so that the flared end
faces the front of the trike.
• Fit the base/handle covers onto the trike rear frame near
the rear wheels.
• Insert two #10 x ¾"
and tighten.
Assembly is now complete.
screws into each base/handle cover
Ride-on Rocker
IMPORTANT! Be sure to adjust the seat in the most
forward position for Ride-on Rocker mode.
Label Application
Handle
Center of Label
Place Center
of Label Here
• Before applying the label, wipe the surface of the
handle with a clean, dry cloth to remove any dust or oils.
• Remove the backing from the label.
• First, position the center of the label on the handle,
as shown. Then, smooth each end of the label outward
to attach it to the handle.
• For best results, avoid repositioning a label once it has
been applied to the handle.
Front Wheel
Wheel Retainer
• Insert the base/handle pin through one wheel retainer,
a hole in the front wheel and into the other wheel retainer.
• Push the handle pin to “snap” it into place. Pull on the
handle pin to be sure it is secure.
Base/Handle Pin
Wheel Retainer
9
Learn to Pedal Trike
Learn to Pedal Trike
Base/Handle
2
• Rotate the base/handle to the upright position.
1
Wheel Retainer
• If you are converting from the ride-on rocker mode, remove
the handle pin from the wheel retainers and front wheel.
Front Wheel
Wheel Retainer
Handle Pin
3
Base/Handle
• Insert the handle pin through one side of the base/handle,
through the holes in the back of the frame and out through
the hole in the other side of the base/handle. Make sure
the handle pin “snaps” into place.
• Pull on the handle pin to be sure it is secure.
10
Handle Pin
Pedal Trike
1
Base/Handle
Handle Pin
• If you are converting from the learn to pedal trike mode,
remove the handle pin from the base/handle and the back
of the frame.
Base/Handle
2
• Rotate the base/handle down, under the trike, to the
ride-on rocker position.
11
Pedal Trike
Storage
Base/Handle Cover
3
Base/Handle
• Remove the screws from the base/handle covers.
• Remove the base/handle covers.
• Remove the base/handle.
Flared End
Handle Cover
Handle Cover
Helpful Hint: To store for future use, position the handle
covers with the flared end upright and attach them to the
handle using the four screws. Insert the handle pin into
either the holes in the base/handle or through the holes
in the retainers. Store the base/handle in a safe place for
future use as a ride-on rocker or learn to pedal trike.
Handle Pin
4
• Rotate the footrest up toward the rear wheels and snap it
into the recess in the underside of the frame.
IMPORTANT! It is a good practice to start training
children very young regarding the importance of helmet
use. When children are older and riding bicycles and
faster vehicles, it is important that they use a helmet
each and every time they ride. For this reason, even
while riding a tricycle, it is a good idea to familiarize
your child with helmet use, so that it becomes a habit
for life. Choose a helmet that complies with requirements
of the applicable certifying agency for bicycle helmets.
Maintenance
• Check plastic parts regularly and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If
the fasteners are not tight, tighten them as necessary.
• To clean this product, use a mild soap and water solution
and a clean cloth. Rinse clean with water to remove
soap residue.
12
Loading...