Fisher-Price 72824 Instruction Sheet
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©1999 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S.trademarks of Mattel, Inc.
Printed in Hong Kong 72824A - 0920
®
Fisher-Price
Instructions
2-in-1 RC Truck
™
Product Number 72824
Please keep these instructions for future reference.
Adult assembly is required to install batteries.
Requires four size “AA” (LR6) alkaline batteries (not included) in the truck.
Requires one 9-volt (6LR61) alkaline battery (not included) in the transmitter.
Tool needed for battery installation: Phillips Screwdriver.
Questions? We’d like to hear from you!
Call Fisher-Price®Consumer Affairs, toll-free at 1-800-432-KIDS, 8AM-5 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.Or, write to:
Fisher-Price®Consumer Affairs, 636 Girard Avenue, East Aurora, New York 14052.
2
-
-
+
+
IMPORTANT!
Radio interference can occur if more than one
radio control vehicle or another radio device is
operating on the same frequency. Radio
interference can also occur near high voltage
electrical wires, reinforced concrete buildings or
trucks with CB radios.
Radio interference can cause this product to work
erratically. For best performance, do not operate
this toy near other radio devices (such as nursery
monitors, cordless telephones or other radio
control vehicles on the same frequency) and
away from high voltage power lines, large buildings
and walls.
Transmitter operates on a 27.145 MHZ carrier
radio frequency.The output power is 10,000 uV/M
@3m which is equivalent to 80dBuV/M.
Battery Installation
Hint: The 9-volt (6LR61) battery in the transmitter
has a longer life than the “AA”(LR6) batteries in
the truck.You may need to change the “AA”
batteries more often than the 9-volt battery.
1.5V x 4
“AA”(LR6)
9V
(6LR61)
BOTH SHOWN ACTUAL SIZE
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries:alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Remove the batteries during long periods of nonuse.Always remove e xhausted batteries from the
product.Battery leakage and corrosion can
damage the product.
• Never short circuit the battery terminals.
Battery Installation
• Non-rechargeable batteries are not to be
recharged.
• Only batteries of the same or equivalent type as
recommended in the “Battery Installation”
instructions are to be used.
• If removable rechargeab le batteries are used, they
are only to be charged under adult supervision.
• Rechargeable batteries are to be removed from the
product before they are charged.
• If you use a battery charger, it should be examined
regularly for damage to the cord, plug, enclosure
and other parts. Do not use a damaged battery
charger until it has been properly repaired.
Truck Batteries
• Turn the truck upside
down.
• Loosen the screw in
the battery compartment door with a
Phillips screwdriver.
• Remove the battery
compartment door.
• Insert four, size “AA”
alkaline batteries, as
indicated inside the
battery compartment.
• Fit the tab on the battery compartment door into
the slot in the battery compartment. Close the
battery compartment door and tighten the screw
with a Phillips screwdriver. Do not over-tighten.
Battery Compartment
Transmitter Battery
• Loosen the screw in
the battery compartment door with a
Phillips screwdriver.
• Open the battery
compartment door.
• Snap a 9-volt battery
to the battery contacts
and insert it into the
battery compartment.
• Close the battery
compartment door and
tighten the screw with
a Phillips screwdriver. Do not over-tighten.
Battery
Compartment
Loading...