Rock, Roll ‘n Ride Trike
Rock, Roll ‘n Ride Trike
TM
Instructions
Model Number: 72669
Please keep these instructions for future reference, as they contain important information.
Adult assembly is required.
Age: 1
1
/2years - 5 years.
Weight Limit: 50 lbs.
Tools needed for assembly: Phillips Screwdriver, Hammer
and Scrap Block of Wood (all not included).
If you have any questions about this product, or are missing a part, please call
us toll-free at 1-800-432-KIDS, rather than return this product to the store.
WARNING
• Adult supervision is required.
• Never use near steps, sloped driveways, hills, roadways,
alleys, swimming pools or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
This product requires adult assembly. Please set aside at least 30 minutes for assembly. Please read these instructions carefully and identify all parts before assembly. Refer to the parts illustration and parts list for identification.
Call Fisher-Price
®
Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-
impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Fisher-Price
®
Consumer Relations,
636 Girard Avenue, East Aurora, New York 14052.
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain
: telephone 01628 500303.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer
Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Consumer Information
Fasteners
Fasteners
All SHOWN ACTUAL SIZE
Lock Washer – 2
#8 x 3" Screw – 1
#8 x
3
/
4
" Screw – 13
Cap Nut – 2
Consumer Information
2
2
Parts
Parts
Fisher-Price
Seat Pin
Seat
Handlebar
Handle Pin
Frame Cover
2 Retainers
Handle
2 Handle Covers
Fork
Front Wheel
2 Fork Covers
4 Pedal Axle Covers
Pedal Axle
2 Lock Washers
2 Pedals
Straight Axle
2 Rear Wheels
2 Cap Nuts
Frame
Footrest
Note: This product contains one
handle and one handle pin. The
handle and handle pin can be
assembled in either the Ride-on
Rocker (page 9) or Learn to Pedal
(page 9) mode.
3
3
Assembly
Assembly
• Please save all packaging material until assembly is complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry, cloth before assembling this product.
CAUTION
This product contains small parts in its
unassembled state. Adult assembly is required.
• Place a cap nut on a scrap block of wood.
• Place one end of the straight axle into the cap nut.
• Tap the cap nut with a hammer. Make sure the cap nut is
securely attached to the straight axle.
1
Straight Axle
Cap Nut
2
Straight Axle
Rear Wheel
Spoke Side Down
3
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Frame
Hole
Hole
Straight Axle
• Slide a rear wheel (spoke side down) onto the straight axle.
Bottom View
4
4
Scrap Block
of Wood
Assembly
Assembly
4
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the assembled rear wheel on the scrap block
of wood.
• Slide the other rear wheel (spoke side up) onto the end of
the straight axle.
• Place a cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel up to be sure the cap nut is securely attached
to the straight axle.
• Set the frame assembly aside.
Cap Nut
Rear Wheel
Straight Axle
Spoke Side Up
Assembled
Rear Wheel
• Fit two pedal axle covers onto the pedal axle metal tabs.
Make sure the metal tabs fit into the slot in each pedal
axle cover.
5
Pedal Axle Cover
Pedal Axle
Metal Tab
Slot
Pedal Axle Cover
• While holding the pedal axle covers on the pedal axle,
insert the pedal axle into the hole in the center of the
front wheel.
6
Pedal Axle Covers
Pedal Axle
Hole
Front Wheel
• Push the pedal axle covers into the center of the front
wheel until they are flush with the surface of the
front wheel.
7
Pedal Axle Covers
• Turn the front wheel assembly over.
• Insert a pedal axle cover onto the top of the pedal axle
and into the hole in the center of the front wheel.
• Insert the remaining pedal axle cover below the pedal axle
and into the hole in the center of the front wheel.
8
Pedal Axle Cover
Pedal Axle Cover
Pedal Axle
5
5
Scrap Block
of Wood
Assembly
Assembly
9
•
Push the pedal axle covers into the center of the front wheel
until they are flush with the surface of the front wheel.
• Insert a lock washer into the slot in a pedal. Make sure the
raised tabs on the lock washer are facing the “closed”, or
outside end of the pedal.
• Insert the other lock washer into the other pedal.
10
Pedal Axle Covers
Lock Washer
Raised Tabs
Slot
Closed
(Outside) End
6
6
•
Place a scrap block of wood under the front wheel assembly.
• Place a pedal on the pedal axle.
• With the pedal lock washer centered over the pedal axle
end, tap the pedal with a hammer until it is secure.
• Repeat this procedure to attach the other pedal to the
other end of the pedal axle.
11
Lock Washer
(inside)
Pedal
Pedal Axle
Front Wheel
Assembly
• Place the front wheel assembly between the fork arms so
that the pedal axle fits into the groove at the bottom of
each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" screws into the fork cover and tighten
with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
12
Fork Cover
Fork Arms
Groove
Pedal Axle
#8 x
3
/4" Screw - 4
SHOWN ACTUAL SIZE
Scrap Block
of Wood
Front Wheel Assembly
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2001 Mattel, Inc. All Rights Reserved.
® and TMdesignate U.S. trademarks of Mattel, Inc.
Printed in Mexico
72669a-0920
• Insert the knobbed end of the footrest up through the
opening in the underside, center of the frame .
• Rotate the footrest 1/4turn .
• Slide the footrest toward the handlebar as far as it will go
until the top of the footrest is positioned over the opening’s
rectangular cut-out.
• Lower the knobbed end of the footrest into the rectangular
cut-out in the frame .
Assembly
Assembly
• Turn the frame upright.
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
13
Handlebar
Frame Neck
Fork Covers
Fork Post
#8 x 3" Screw - 1
SHOWN ACTUAL SIZE
14
Frame Opening
Footrest
Knobbed End
7
7
•
Place the frame cover over the frame opening. Make sure
that the holes in the frame cover align with the holes on
the frame.
• Insert three #8 x 3/4" screws into the frame cover and tighten
with a Phillips screwdriver. Do not over-tighten.
15
Frame Cover
#8 x 3/4" Screw - 3
SHOWN ACTUAL SIZE
• Place the seat on the seat mount.
• Adjust the seat for your child’s comfort by aligning the hole
in the seat with one of the seat mount adjustment holes.
16
Seat Mount Adjustment Holes
Seat
Seat Mount
2
➥
➥
3
➥
1
2
3
1
Rear of Trike
Assembly
Assembly
• While pushing down on the seat, insert the seat retainer
pin through the hole in the seat and into a seat mount
adjustment hole.
17
Seat Retainer Pin
• Fit the retainers to the handle, as shown.
• Insert three #8 x
3
/4" screws through each retainer and into
the handle. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
18
Retainer
Handle
#8 x 3/4" Screw - 6
SHOWN ACTUAL SIZE
8
8
19
• Position the handle on a flat surface so that the retainers
are upright.
• Fit the trike onto the handle so that the rear frame rests in
the grooves in the handle and the front wheel fits between
the retainers.
• Fit the handle covers onto the rear frame and handle, near
the rear wheels.
• Insert two #10 x 3/4"
screws through each handle cover
and into the handle. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
Assembly is now complete.
Handle
Retainers
Trike
#10 x 3/4" Screw - 4
SHOWN ACTUAL SIZE
Retainer
Ride-on Rocker
Ride-on Rocker
• Insert the handle pin through one retainer, a hole in the
front wheel and into the other retainer.
• Push the handle pin to “snap” it into place. Pull on the
handle pin to be sure it is secure.
Retainer
Front Wheel
Retainer
Handle Pin
9
9
Learn to Pedal Trike
Learn to Pedal Trike
• If you are converting from the ride-on rocker mode, remove
the handle pin from the handle retainers and front wheel.
1
Retainer
Front Wheel
Retainer
Handle Pin
IMPORTANT! Be sure to adjust the seat in the most forward
position for Ride-on Rocker mode.
3
2
Handle
• Insert the handle pin through one side of the handle,
through the holes in the back of the frame and out through
the hole in the other side of the handle. Make sure you
hear the handle pin “snap” into place.
• Pull on the handle pin to be sure it is secure.
Handle
• Rotate the handle to the upright position, as shown.
Handle Pin
Learn to Pedal Trike
Learn to Pedal Trike
10
10
Pedal Trike
Pedal Trike
1
Handle
• If you are converting from the learn to pedal trike mode,
remove the handle pin from the handle and the back of
the frame.
Handle Pin
Pedal Trike
Pedal Trike
2
Handle
• Rotate the handle down, under the trike, to the ride-on
rocker position.
3
Handle
Handle Cover
• Remove the screws from the handle covers.
• Remove the handle covers.
• Remove the handle.
11
11
• Rotate the footrest up towards the rear wheels and snap it
into the recess in the underside of the frame.
4
Storage
Storage
Maintenance
Maintenance
• Check plastic parts regularly and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If
the fasteners are not tight, tighten them as necessary.
• To clean this product, use a mild soap and water solution
and a clean cloth. Rinse clean with water to remove
soap residue.
Helpful Hint: To store for future use, attach the handle
covers to the handle using the four screws. Insert the handle
pin into either the holes in the handle or through the holes in
the retainers. Store the handle in a safe place for future use
as a ride-on rocker or learn to pedal trike.
Handle Cover
Handle Pin
Handle Cover
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone 01628 500303.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
12
12
Loading...