Page 1
Big Action™Construction
Model Number 72028
Product features may vary slightly from the picture above.
Please keep this instruction sheet, as it contains important information.
Adult assembly is required.
No tools are needed for assembly.
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Questions? We'd like to hear from you!
Call Fisher-Price
®
Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST
Monday through Friday.Hearing-impaired consumers using TTY/TDD equipment, please call
1-800-382-7470. Or, write to: Fisher-Price
®
Consumer Relations, 636 Girard Avenue,
East Aurora, New York 14052.
Big Action™Construction
Page 2
®
Base
Dump Truck
Front Loader
4 Boulders
Drawbridge
Hopper
Tower Bucket
Crane Jaws
Door/Ramp
Rotating Crane Boom
Hopper Tower
Hopper
Tower Top
Turnabout
Chute
Crane Tower
Dump
Tower
Door
Crank
Plunger
Gas Pump Hose
2
Parts
Page 3
Tab
Slot
Hopper
Tower
Column
• Position the hoppertowerso that the doorway facesout.
• Insert the column on the side of the hopper tower into
the groove near the chute in the base (see inset).
• Align the tabs on the bottom of the hopper tower with
the slots in the base.
• Press down to "snap" the hopper tower into place.
Groove
Chute
• Insert and "snap" the peg on the end of the gas
pump hose into the hole in the base.
Place Boulders
Here For Launching
• Do not launch the boulders at point
blank range.
• Use only the boulders supplied with this toy.
Peg
Holes
Tab
Hole
Groove
Detonator
Plunger
• Align the tab on the plunger stem with the groove in
the hole in the top of the detonator.
• Push the plunger into the hole until it "snaps"
into place.
• You can launch the boulders after assembling the
plunger.To launch the boulders, place them in the
opening in the base and push the plunger down to
send them flying!
Peg
Hole
Gas Pump
Hose
Drawbridge
• At an angle, insert a peg on the drawbridge into one of
the holes in the base.
• Then, fit the other drawbridge peg into the other hole in
the base.
3
CAUTION
Peg
1
2
3
4
Assembly and Use
Page 4
Door/Ramp
Side Rail
Side Rail
Hole
Hole
Peg
Peg
• Position the door/ramp so that the side rails are upright.
• Insert a peg on the door/ramp into a hole in the
door opening.
• Insert and "snap" the other door/ramp peg into the
other hole in the door opening.
• Rotate the door up to close, or down to use it as
a ramp.
Hint: After a busy day, store the vehicles and boulders
inside the hopper tower.Then, rotate the door up to close.
• Fit the pegs on the hopper tower bucket into the inner
holes in the hopper tower hinge.
Inner Holes
Turnabout
Opening
• Align the opening in the turnabout with a chute in
the hopper tower top and "snap" the turnabout down
into place.
• Slide the turnabout to send a boulder down either chute
in the hopper tower top!
Hopper
Tower Top
Chute
• Fit the pegs on the hopper tower top into the outer
holes in the hopper tower hinge.
Outer Holes
Pegs
Hopper
Tower T op
Hinge
Pegs
Hopper
Tower
Bucket
Hinge
4
5
6
7
8
Assembly and Use
Page 5
• Align the tabs on the bottom of the crane tower with
the grooves in the base.
• Insert and press down to "snap" the crane tower
into place.
Crane Tower
Tabs
Grooves
Base
Rotating
Crane
Boom
Crane Tower
Crank
Crane Jaws
Lever
• Fit the rotating crane boom onto the top of the
crane tower.
• Use the crank on either side of the rotating crane boom
to raise or lower the crane jaws!
• Push the lever toward the crane jaws to open them when
the jaws are cranked all the way to the top. Open and
close the jaws by hand in any position.
Note: The rotating crane boom is designed to break away
from the crane tower. If it detaches from the crane tower,
simply reattach it.
• Insert a peg on the chute into the hole in the crane tower.
• Insert and "snap" the otherchute peg into the other hole
in the crane tower.
One-time assembly is now complete.
Peg
Chute
Hole
Peg
Hole
Crane Tower
5
• Insert the peg on the dump tower door into the hole in
the dump tower.
• "Snap" the hinge on the dump tower door into the slot
in the dump tower.
Dump Tower
Peg
Hole
Dump Tower
Door
Slot
Assembly and Use
9
10
11
12
Page 6
®
• Make sure the areas where the labels will be applied are clean and dry.
• Apply the labels as indicated in the illustration.
• For best adhesion, avoid applying the labels more than once.
1
2
3
15
6
10
14
13
8
9
5
4
11
7
12
For other countries, outside the United States:Canada: call 1-800-567-7724, or write to:Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain:
telephone 01628 500303. Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Label Decoration
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. 72028b-0920
© 2001 Mattel, Inc. All Rights Reserved.® and ™ designate U.S. trademarks of Mattel, Inc. Printed in U.S.A.
Loading...