Fisher & Paykel OB76SDPTDX1 User Manual

BUILT-IN OVEN

OB76S & OB76D

touchscreen models

INSTALLATION GUIDE

NZ AU

SAFETY AND WARNINGS

WARNING!

Electric Shock Hazard

Failure to follow this advice may result in electric shock or death.

• Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply.

• Connection to a good earth wiring system is absolutely essential and mandatory.

• Alterations to the domestic wiring system must only be made by a qualified electrician.

WARNING!

Fire Hazard

Failure to follow this advice may result in overheating, burning, and injury.

• Do not use adapters, reducers, or branching devices to connect this appliance to the mains power supply.

WARNING!

To avoid hazard, follow these instructions carefully before installing or using this appliance.

Please make this information available to the person installing the appliance — doing so could reduce your installation costs.

This appliance must be installed and connected to the mains power supply only by asuitably qualified person according to these installation instructions and incompliancewith any applicable local building and electricity regulations. Failure to install the appliance correctly could invalidate any warranty or liability claims.

If the installation requires alterations to the domestic electrical system, call a qualifiedelectrician. The electrician should also check that the socket cable section issuitable forthe electricity drawn by the oven.

The oven must be earthed.

If the power supply cable is damaged, it must be replaced by the manufacturer, itsservice agent or similarly qualified person in order to avoid a hazard.

Isolating switch: ensure this oven is connected to a circuit which incorporates anisolating switch providing full disconnection from the power supply in accordance with the wiring rules.

Do not use adaptors, reducers or branching devices to connect the oven to the mains electricity supply, as they can cause overheating and burning.

Ensure the cavity is completely sealed with no gaps. This is to ensure the oven cooling system functions correctly.

The appliance must not be installed behind a decorative door in order to avoidoverheating.

WARNING!

Cut Hazard

Failure to use caution could result in injury.

• Take care: some edges are sharp.

Very Heavy

Failure to follow this advice may result in serious injury.

• Do not attempt to lift this product unassisted.

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher&Paykel dealer.

PARTS SUPPLIED

Screws

Single oven models (2) Double oven models (4)

Spacers

Single oven models (2) Double oven models (4)

Long Trim (1)

To be fitted in a flush installation.

PRIOR TO INSTALLATION

the benchtop and oven cavity are square and level, and are the required dimensions.

the installation will comply with all clearance requirements and applicable standards and regulations.

a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements).

the isolating switch will be easily accessible to the customer with the oven installed.

the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening.

the cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.

the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.

the oven will rest on a surface that can support its weight.

the height from the floor suits the customer.

you consult local building authorities and by-laws if in doubt regarding installation.

IMPORTANT!

Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cavity.

AFTER INSTALLATION

IMPORTANT!

Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

the oven door(s) can open fully without obstruction.

do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher&Paykel will not cover the costs of removing the oven, or of damage caused by thisremoval.

the power supply cable does not touch any hot metal parts.

the isolating switch is easily accessible to the customer with the oven installed.

you complete the ‘Final checklist’ at the end of the installation.

if, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher&Paykel Authorized Service Center, Customer Care, or contact us through our local website listed at the end of this document.

PRODUCT DIMENSIONS — SINGLE OVENS

PRODUCT DIMENSIONS

PROFILEFRONT

OB76SD

PLAN

A Overall height of product 690

B Overall width of product 760

C Overall depth of product (excl. handle and dials) 610

D Depth of oven front and control panel (excl. handle and dials) 40

E Depth of chassis (does not include oven front) 569

F Height of chassis 675

G Depth of door (open) (measured from front of door) 550

H Overall width of chassis 720

Note: If flush installing, you need to replace the lower trim with the supplied long trim at the base of the oven, and the depth of the control panel G with the fitted spacer is larger than conventional ovens. Ensure you have created a 42mm recess incabinetry.

+ 11 hidden pages