Page 1
WARNING!
Electrical hazard
Always disconnect the oven from
the mains electricity supply
before carrying out any
maintenance operations or
repairs.
Failure to do so may result in
electrical shock or death.
Important safety precautions!
To avoid hazard, follow these instructions carefully before installing or using this product.
Please make this information available to the person installing the product as it could reduce your
installation costs.
This oven is to be installed and connected to the electricity supply only by an authorised person.
If the installation requires alterations to the domestic electrical system, call a qualied electrician. The
electrician should also check that the socket cable section is suitable for the electricity drawn by the oven.
The oven must be earthed.
To connect the oven to the mains, do not use adapters, reducers or branching devices as they can cause
overheating and burning.
Installation must comply with your local building and electricity regulations.
Failure to install the oven correctly could invalidate any warranty or liability claims.
SAFETY AND WARNINGS
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
1
Before you install the oven, please make sure that
The oven will rest on a at surface that can support its weight.
The benchtop and oven cavity are square and level, and are the required dimensions.
The height from the oor suits the user.
The oven door can open fully without obstruction.
a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to
comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm air gap
contact separation in all poles must be incorporated into the xed wiring in accordance with the wiring
rules, unless the local wiring rules allow for the following variation:
A means of disconnection from the supply having and air gap separation in all active (phase) conductors
must be incorporated into the xed wiring.
the electrician provides sucient free length of power supply cable to reach from the bottom rear of the
cavity to at least 1.5 metres in front of the bottom edge of the opening. The cable may enter the cavity
from the side, top or bottom, but top entry must be at the rear of the cavity.
When you install the oven
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing dicult. Fisher &
Paykel will not cover the costs of removing the oven, or of damage caused by this removal.
Use the supplied screws and spacers to secure the oven to the cabinetry. Do not over-tighten the screws.
Do not stand on the door, or place heavy objects on it.
Do not lift the oven by the door handle.
Take extra care not to damage the lower trim of the oven.
Use easy-to-clean nishes for the wall surfaces surrounding the oven, so that cooking fume staining
resulting from using the oven is easy to remove.
Aerotech oven
Installation instructions
OB76 models
NZ AU
409 lb
186 kg
242 lb
110 kg
WARNING!
Very Heavy
Do not attempt to lift this
product unassisted.
Lifting unassisted may
cause serious injury.
SINGLE
OVEN
MODELS
DOUBLE
OVEN
MODELS
Page 2
2
PRODUCT AND CABINETRY DIMENSIONS
Double oven models
Single oven models
A
B
C
E
D
F
G
H
J
K
Product and cabinetry dimensions (mm)
OB76 S
models
A
overall height of product 688
B
overall width of product 757
C
overall depth of product (without handle) 608
D
height of chassis 675
E
width of chassis 718
F
depth of chassis 570
G
depth of oven frame and control panel (excl. knobs) 38
H
depth of oven door (open) (measured from front of oven frame) 530
I
minimum inside width of cavity 724
I
I
overall width of cabinetry 762
J
inside height of cavity 681
J
I
overall height of cabinetry 693
K
minimum inside depth of cavity 575
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the
cooktop manufacturer’s instructions.
A
C
D
E
F
G
H
I
J
K
Installation diagrams for illustration purposes only
I
I
J
I
I
I
J
I
Ensure the cavity is completely sealed with no gaps
Ensure the cavity is completely sealed with no gaps
Product and cabinetry dimensions (mm)
OB76 D
models
A
overall height of product 1230
B
overall width of product 757
C
overall depth of product (without handle) 608
D
height of chassis 1217
E
width of chassis 718
F
depth of chassis 570
G
depth of oven frame and control panel (excl. knobs) 38
H
depth of oven doors (open) (measured from front of oven frame) 530
I
minimum inside width of cavity 724
I
I
overall width of cabinetry 762
J
inside height of cavity 1222
J
I
overall height of cabinetry 1235
K
minimum inside depth of cavity 575
I
Flush installProud install
B
Proud install
Flush install
3
PRODUCT AND CABINETRY DIMENSIONS
G
G
16-20 mm
16-20 mm
16-20 mm
16-20 mm
2.5 mm
2.5 mm
mm 5.2mm 5.2
Page 3
1
1
4
4
2
3
1
A
54
6
NOITCENNOC LACIRTCELENOITARAPERP YRTENIBAC
UNPACK THE OVEN AND REMOVE THE DOOR(S)
B
Double models featured for illustration purposes only
OB76 Single
Max. current draw: 19.4 A
Max. load: 4.6 kW
OB76 Double
Max. current draw: 38.3 A
Max. load: 9.2 kW
Nameplate
Important!
Ensure you have
created a 38 mm recess
in cabinetry if ush
installing.
llatsni hsulFllatsni duorP
Important!
Ensure you remove
the long trim from
the packaging
We recommend that the outlet for the power supply cable is located in the
right rear corner of the cabinet cavity. This allows the power supply cable
to sit inside the rear chamfered corner of the oven and prevents it being
jammed between the cabinet wall and the rear of the oven.
38 mm16-20 mm
mm 575mm 575
613 mm
Page 4
1
2
1
FLUSH INSTALLATION ONLY - REPLACE THE LOWER TRIM WITH THE SUPPLIED LONG TRIM
A B
7
Unscrew and remove the
installed lower trim
1
1
1
4
3
1
1
2
2
2
SECURE THE OVEN TO THE CABINETRY AND REFIT THE DOOR(S)
A B
8
Take care not to
damage the lower trim
of the oven
Ensure supplied spacer
is tted between oven
and cabinetry
Please turn over >
Replace with the
supplied long trim
Ensure the clips
on the long trim
locate into the
channels
Page 5
Make sure the appliance is level and securely tted to the cabinetry and both
oven doors open and close freely.
Make sure all the internal packaging has been removed from the oven cavity.
Make sure all oven vents and openings are clear and are free of any
obstruction/damage.
Important!
Failure to make sure all oven vents are unobstructed may result in poor product performance.
Turn the power to the oven on. The clock should light up and ash 12:00pm.
Set the clock to the current time.
1) Rotate the
PU SH T O
CLEA R
button until the correct time is showing.
2) Press the CLOCK button to set the time, or wait eight seconds and it will set
automatically.
Turn the oven function knob to ‘Bake’ and the oven temperature knob to
180
o
C. Air should blow out of the vent at the bottom of the oven. Inside the
oven cavity, all three oven lights should come on. After ve minutes, open the
oven door and the air inside should feel warm and the top element should be
glowing red.
Turn both the oven function knob and oven temperature knob back to OFF
and repeat for the other oven if the appliance is a double model.
10
TROUBLESHOOTING
If the appliance is not functioning correctly after installation, check the
following:
Check that the circuit breaker has not tripped or the fuse blown.
Make sure that the electrical connections have been correctly made.
Make sure that power is being supplied to the oven.
Make sure the voltage is correct across all phases.
If a problem occurs, consult the Troubleshooting section of the User Guide.
If after checking these points you still need assistance, please refer to the
Service & Warranty book for warranty details and your nearest Authorised
Service Centre, or contact us through our website, www.sherpaykel.com.
9
FINAL CHECKLIST
Page 6
599510A NZ AU 03.08
Loading...