Fisher & Paykel Built-in oven, OB60SL9DEX Quick Start Manual
ERUTAREPMETNOITCNUF
YOUR OVEN
OB60SL9DEX
THE CONTROL PANEL
FIRST USE
1 REMOVE ALL CABLE TIES & PACKAGING HOLDING
THE SHELVING IN PLACE
3 REMOVE BOTH SIDE RACKS
2 REMOVE ALL SHELVES FROM THE OVEN
Keep this document handy for easy reference.
For detailed information on the other features of your oven, see your ‘User guide’.
Before using your oven, make sure you read the full ‘User guide’, with special attention to the ‘Safety and warnings’ section.
For contact information or if you require service, assistance or replacement parts, see the end of this document or your ‘Service & warranty’
booklet.
NZ AU GB IE
QUICK START GUIDE
Built-in oven
1
Control panel
2
Oven vent louvres
3
Step down oven wire shelf
4
Oven light
5
Telescopic sliding shelf
6
Side rack
7
Oven wire shelf
8
Oven door and handle
9
Oven seal
Accessories:
10
Grill rack
11
Smokeless grill tray
12
Deep Roasting dish
13
Flat baking tray
14
Catalytic panels
10
11
12
13
14
2
3
4
5
6
7
retaining wire
lock stud
8
1
9
Important!
Before using your oven for the first time, you should fit both
the Catalytic Panels (supplied). See ‘Care and cleaning’ in
your user guide for details about these self cleaning panels.
You do this by:
removing ALL the cable ties holding the shelving in place,
if the installer has not already done so.
removing the shelves and side racks
fitting the catalytic panels
replacing the side racks and shelves
We recommend you then condition the oven.
Follow the steps below to fit the Catalytic Panels.
1
Remove all the shelving, taking special care with the telescopic
sliding shelves.
2
To remove a telescopic sliding shelf, grip it at the front (making
sure you are gripping the wire shelf and the sliding frame
together), lift upwards and pull it out of the oven.
For your safety, the wire shelf and telescopic sliding frame are
built together as one unit and are not separable.
Remove both side racks by 1)
pushing down on the retaining
wire until it clears the lower lock
stud and swing out wards to 2)
clear the upper lock studs, then
3) lift out.
1
3
2
2
Function indicators
(see ‘Oven functions’)
Function dial Temperature
indicator
Temperature
dial
Function halo
Temperature
halo
Timer indicator
(see ‘Using the
timer’)
if lit:
Timer is counting
down
Rotisserie indicator
(see ‘Using the
Rotisserie’) in the
User guide
if lit:
Rotisserie is
in use
Cooking time indicator (see ‘Automatic cooking’) in User guide
if lit:
Automatic cooking time is set
Stop time indicator
(see ‘Automatic cooking’) in User guide
if lit:
Automatic stop time is set
Display
Scroll Select Cancel
continued over
SETTING THE CLOCK
You set the clock within the user preference menu. To learn more about the user preference menu, refer to your User guide.
Note: If you do not wish to set the time initially when the oven is first switched on at the wall, press the cancel
button to exit the clock setting.
If you want to set the clock later, follow the steps under ‘ To change the time’.
When the oven is first switched on at the wall
3
Press the left and right scroll
buttons to set the time.
1
The display will flash 24 Hr.
4
Press the select
button to confirm.
The time set will now be steadily lit.
2a
Press the right scroll button to scroll
between
24 Hrand 12 Hr
2b
Press the select
button to confirm.
To change the time
(within the user preference menu)
Locking the control panel
To lock, press and hold the select
button for 2 seconds.
To unlock, press and hold the
cancel button for 2 seconds.
Control lock indicator (see
‘Locking the control panel’)
if lit:
Control panel is locked
1
Press and hold the left and right scroll
buttons together for 3 seconds
to enter the user preference menu.
The display will either show 12 Hror 24
Hr
2
Press the select
button to confirm.
The display will flash.
3
Follow steps 2-5 left to set the time.
At step 2a, you also now have the
ability to scroll between
24 Hr,
12 Hr and OFF (turns the display off).
Refer to the User guide to learn more
about this feature.
There will be a distinctive smell and a small amount of smoke during the conditioning process as manufacturing residue is burnt off.
This is normal, but make sure the kitchen is well ventilated during the conditioning.
Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.
It is important to condition your oven before using it for cooking and baking. Conditioning will burn off any manufacturing residues and ensure
that you get the best results right from the start.
1
Make sure you have removed ALL the cable ties used to secure the shelving during transit.
2
Make sure you have set the clock.
3
Make sure all the shelves are fitted.
USING THE TIMER
FOR MORE INFO
FIRST USE
7 CONDITION THE OVEN
7 CONDITION THE OVEN
4 FIT BOTH CATALYTIC PANELS
5 REPLACE BOTH SIDE RACKS
6 REPLACE SHELVING
Catalytic panel
Stop Notch
Guard rail
Guard
rail
Front bar
Rear shelf tagFront shelf tag
To replace a wire shelf, check the guard rail (as shown) to make sure the shelf is the right way up. slide it horizontally back along the side racks
ensuring it is level and the stop notch is facing down.
To replace a telescopic sliding shelf, position it so that the front bar is toward you, as shown.
Check that the sliding frame is not extended.
Check the guard rail (as shown) to make sure the shelf is the right way up.
Position the shelf so that it is level and the rear shelf tag at the back of the sliding frame rests behind the side rack wire (as shown).
Then push the sliding shelf all the way to the back of the oven, until the front shelf tag drops into place behind the side rack wire.
For your safety, the wire shelves and telescopic sliding frames are built together as one unit and are not separable. This means that when placed
properly on the side racks, the slides will prevent the wire shelves from tilting when pulled towards you.
To prevent the tags from lifting off the side racks, take care to slide the shelves forward horizontally.
Place each catalytic panel flush against the side wall, noting
the position of the cutouts for the lamp and lock nuts
To replace the side racks, locate the top of the side rack into the
two upper lock studs and gently push the retaining wire back
under the lower lock stud.
NOITCNUF
ERUTAREPMET
1
1
2
Replacing a wire shelf
Replacing a telescopic sliding shelf
retaining wire
lock stud
7
Leave the temperature at 200 oC
for 5 minutes.
The halo will remain white.
1
Select the timer by pressing
the right scroll
button once.
The timer indicator will appear
and the colon will flash.
2
Press the select
button to
confirm.
The display will flash to indicate
the timer is ready to be set.
3
Set the time by pressing the
scroll
buttons.
Holding the buttons down
will speed up the scrolling.
4
Press the select
button to
confirm.
The timer will then begin to
count down.
If you want to check the time
of day, press the cancel
button once.
Press the right scroll
button
to scroll back to the timer.
8
When you have finished, turn the function dial to
Off
. The halos will go out.
You can use the timer at any time, even if you are not using the oven.
If the time is more than an hour, the display will count down in minutes (hr:min). If it is less than an hour, it will count down in seconds (min:sec).
You can set the timer for up to 23 hours 59 minutes.
Important!
The timer does NOT turn the oven off.
To modify the timer setting
1
Make sure the display shows the remaining time counting down.
2
Press the select
button.
3
Press the scroll buttons to set a new time.
4
Press the select
button to confirm.
To cancel the timer setting
1
Make sure the display shows the remaining time counting down.
2
Press the cancel button until the display shows the time of day and the timer indicator disappears.
When the set time is up
The display will show 0:00 and a tone will sound every 15 seconds.
Press any button to stop the tone sounding. The display will rever t to showing the time of day.
For detailed information on the
other features of your oven
For warranty information
If you…
have any questions or comments
need a Fisher & Paykel authorized
technician to service your product
need replacement parts or accessories
want to register your product
see your ‘User guide’
see your ‘Service and warranty’ booklet
see your ‘Service and warranty’ booklet or contact us
590479A 12.12
NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
4
Select the Bake function.
The halo will glow white.
Each function has a preset
temperature and so the oven
will start heating at the Bake
preset temperature of 180
o
C.
5
Set the temperature to 200 oC for 30 minutes.
While the oven is heating up, the temperature halo
will glow red and the temperature indicator will
alternately show the actual and set temperatures.
When the oven has reached set temperature, a tone
will sound and the halo will turn white.
6
After 30 minutes is up,
select the Fan Grill
function.
NZ toll-free, 24/7 0800 372 273
AU
toll-free, 24/7 1300 650 590
GB
toll-free, 24/7 0845 066 2200
IE toll-free, 24/7 1800 625 174
www.fisherpaykel.com
Loading...