Fisher & Paykel OB60SC5CEX2, OB60SC7CEW2, OB60SC7CEX2, OB60SD9X1, OB60SC8DEPX2 Installation Guide
...
BUILT-IN OVEN
OB60NC, OB60SC & OB60SD
models
INSTALLATION GUIDE
NZ AU GB IE
590777D 06.18
1 SAFETY AND WARNINGS
!
WARNING!
Electrical shock hazard
Before carrying out any work on the
electrical section of the appliance, it must be
disconnected from the mains electricity supply.
Connection to a good earth wiring system is
absolutely essential and
mandatory.
Alterations to the domestic wiring system must
only be made by a qualified electrician.
Failure to follow this advice may result in
electrical shock or death.
!
WARNING!
Fire hazard
Do not use adapters, reducers, or branching
devices to connect this appliance to the mains
power supply.
Failure to follow this advice may result in
overheating, burning, or fire.
!
WARNING!
Hot Surface Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or
cuts.
IMPORTANT SAFETY INSTRUCTIONS
●
To avoid hazard, follow these instructions carefully
before installing or using this appliance.
●
Please make this information available to the person
installing the appliance - doing so could reduce your
installation costs.
●
This appliance must be installed and connected to
the mains power supply only by a suitably qualified
person according to these installation instructions and
in compliance with any applicable local building and
electricity regulations. Failure to install the appliance
correctly could invalidate any warranty or liability
claims.
●
If the power supply cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.
●
Isolating switch: make sure this oven is connected
to a circuit which incorporates an isolating switch
providing full disconnection from the power supply in
accordance with the wiring rules.
●
The oven must be earthed.
●
Do not use adaptors, reducers or branching devices
to connect the oven to the mains electricity supply, as
they can cause overheating and burning.
●
The appliance must not be installed behind a
decorative door in order to avoid overheating.
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1
2 PARTS SUPPLIED
Screws (2) Metal side shelves
fixing nut (2)
3 PRIOR TO INSTALLATION
●
the benchtop and oven cavity are square and level, and are the required dimensions.
●
the installation will comply with all clearance requirements and applicable standards and regulations.
●
a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and
regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this
variation of the requirements).
●
the isolating switch will be easily accessible to the customer with the oven installed.
●
there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing.
●
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
●
the oven will rest on a surface that can support its weight.
●
the height from the floor suits the customer.
●
you consult local building authorities and by-laws if in doubt regarding installation.
Lower trim kit (for compact models only)
●
compact models can be installed with a lower trim kit accessory to align the oven with companion products and cabinetry. If installing the lower trim kit accessory, ensure that this is installed
before the appliance.
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
4 AFTER INSTALLATION
IMPORTANT!
Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without
obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.
●
the oven door can open fully without obstruction.
●
the power supply cable does not touch any hot metal parts.
●
the isolating switch is easily accessible to the customer with the oven installed.
●
you complete the ‘Final checklist’ at the end of the installation.
●
If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through
our local website listed at the end of this document.
2
5 PRODUCT DIMENSIONS
A
CF
B
E
G
H
D
PRODUCT DIMENSIONS
Overall height of product 458
A
Overall width of product 597 597 596
B
Overall depth of product (excluding handle and dials) 565 565 565
C
Height of chassis 435 575 575
D
Width of chassis 552 552 556
E
Depth of chassis 545 545 545
F
Depth of oven frame and control panel
G
(=distance between front of chassis and front of oven door, excl. knobs)
Depth of oven door when fully open
H
3
(measured from front of control panel)
FRONT
TOP
SIDE
Optional Lower trim kit shown (for compact models only)
(optional accessory. Purchased separately: Part no. 85083)
If using the lower trim kit accessory, you will need to install
this BEFORE installing the appliance. Refer to the
instructions packed with the lower trim kit.
OB60NC MODELS OB60SC MODELS OB60SD MODELS
(with lower trim kit fitted) 479
MM MM MM
20 20 20
340 450 460
598 598
Loading...