Fisher & Paykel OB60Series, OB60 models Installation Instructions Manual

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our
local website listed at the end of this document or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS

1

WARNING!

Electrical shock hazard

Always disconnect the appliance from the mains power supply before

carrying out any maintenance or repairs.
Connection to a good earth wiring system is essential and mandatory.
Alterations to the domestic wiring system must only be made by a
qualified electrician.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Fire hazard

Do not use adapters, reducers, or branching devices to connect this appliance to

the mains power supply.

Failure to follow this advice may result in overheating, burning, or fire.

Important safety instructions!

To avoid hazard, follow these instructions carefully before installing or using this appliance.
Please make this information available to the person installing the appliance - doing so could reduce
your installation costs.
This appliance must be installed and connected to the mains power supply only by a suitably qualified
person according to these installation instructions and in compliance with any applicable local
building and electricity regulations. Failure to install the appliance correctly could invalidate any
warranty or liability claims.
If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

Multifunction ovens

Installation instructions

OB60 models

NZ AU GB IE SG

(1,1) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM

(1,1) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM

2

PRODUCT & CABINETRY DIMENSIONS

Product dimensions (mm)

OB60S

OB60N

A overall height* of product

597 450**

B overall width of product

595 595

C overall depth of product (excluding handle and knobs)

565 554

D height of chassis

582 436

E width of chassis

556 536

F depth of chassis

545 534

G

depth of oven frame and control panel

(=distance between front of chassis and front of oven door, excl. knobs)

20 20

H

depth of oven door when fully open

(measured from front of

control panel)

435 289

I minimum inside width of cavity

560 560

IIoverall width of cavity

600 600

J inside height of cavity

585 440**

JIoverall height of cavity

600 455**

K minimum inside depth of cavity

550 550

L flush fitting cabinetry clearance

20 20

Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop
manufacturer’s instructions.

*All height measurements include mounted feet.

** If  tting the lower trim extension kit, the overall height of product (A) increases by 25 mm (to 475 mm).
The height of the cavity (J and Ji) therefore needs to be increased by 25 mm also (to 465 mm and 480 mm respectively).

Product dimensions (mm)

OB60B

OB60D

A overall height* of product

888 1077

B overall width of product

595 595

C overall depth of product (excluding handle and knobs)

565 565

D height of chassis

874 1057

E width of chassis

556 556

F depth of chassis

545 545

G

depth of oven frame and control panel

(=distance between front of chassis and front of oven door, excl. knobs)

20 20

H

depth of upper oven door when fully open

(measured from front of control panel)

261 435

H

I

depth of lower oven door when fully open

(measured from front of control panel)

435 450

I minimum inside width of cavity

560 560

IIoverall width of cavity

600 600

J inside height of cavity

877 1065

JIoverall height of cavity

893 1082

K minimum inside depth of cavity

550 550

L flush fitting cabinetry clearance

20 20

*All height measurements include mounted feet.

OB60S & OB60N MODELS

Installation diagrams for
illustration purposes only

2.5 mm

16-20 mm

A

C

E

D

F

G

H

J

K

L

L

I

I

I

J

I

B

2.5 mm

16-20 mm

L

A

C

E

D

F

G

H

H

I

J

K

L

I

I

I

J

I

B

OB60B & OB60D MODELS

(1,2) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM

(1,2) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM

LOWER TRIM

OVEN DOOR

LOWER TRIM

AIR FLOW

FEET

PRIOR TO INSTALLATION

UNPACKING THE OVEN

3

4

5

ELECTRICAL CONNECTION

Before you install the oven, make sure that

the benchtop and oven cavity are square and level, and are the required dimensions
the installation will comply with all clearance requirements and applicable standards and regulations
a suitable isolating switch providing full disconnection from the mains power supply is incorporated in
the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
The isolating switch must be of an approved type and provide a 3 mm air gap contact separation
in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the
requirements)
the isolating switch will be easily accessible to the customer with the oven installed
there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for
ease of installation and servicing
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall
the oven will rest on a surface that can support its weight
the height from the floor suits the customer
you consult local building authorities and by-laws if in doubt regarding installation.

Important!

Some environmental factors and cooking habits can cause condensation in and around the oven during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we
recommend moisture-proofing the oven cavity.

Important!

This oven must be connected to the mains power supply only by a suitably qualified person.
This oven must be earthed.

Before connecting the oven to the mains power supply, check that

the domestic wiring system is suitable for the power drawn by the oven

(as specified on the rating plate)

the voltage corresponds to the value given on the rating plate.

Important!

Do not lift the oven by the door handle.

Remove all packaging and dispose of it responsibly. Recycle items that you can.
Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the lower trim.

You may remove the feet, but ensure the oven does not sit on the lower trim

Important!

The lower trim ensures correct air circulation and allows the door to open and close without obstruction. The
manufacturer does not accept any responsibility for damage resulting from incorrect installation.

OB60B & OB60D MODELS

OB60S & OB60N MODELS

Model code Power Voltage

OB60SLC...

2350-2550 W 230 - 240 V~

OB60SLM...

3070 W 220-240 V~

OB60SCE...

3070 W 220-240 V~

OB60SCM...

3070 W 220-240 V~

OB60SCT...

3600 W 230 V~

OB60SDT...

3600 W 230 V~

OB60S9D...

3400 W 220-240 V~

OB60SV...

3070 W 220-240 V~

OB60NL...

2050 W 220-240 V~

OB60NC...

2800 W 220-240 V~

OB60ND...

2800 W 220-240 V~

Model code Power Voltage

OB60BC...

5800 W 220 - 240 V~

OB60BD...

5800 W 220 - 240 V~

OB60B77C...

5850 W 220 - 240 V~

OB60B77D...

5850 W 220 - 240 V~

OB60DD...

6120 W 220 - 240 V~

E

N

L

1

(L )

2

Unhook to open cover

1

2

Unscrew to open

cable clamp

E

N

L

1

(L )

2

Green & Yellow
(Earth)

Brown (Live)

Blue (Neutral)

N

L

D

1

2

Unscrew to

remove cover

plate

Unscrew to remove

cable clamp

(2,1) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM

(2,1) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM