Fisher & Paykel OB60B77DEX3 Installation Guide

(1,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

INSTALLATION INSTRUCTIONS

MULTIFUNCTION OB60 OVENS

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed at the end of this document or contact your local Fisher & Paykel dealer.

1

SAFETY AND WARNINGS

WARNING!

Electrical shock hazard

Always disconnect the appliance from

Cut hazard

Take care - panel edges are sharp.

NZ AU GB IE

the mains power supply before carrying out any maintenance or repairs. Connection to a good earth wiring

Failure to use caution could result in

injury or cuts. system is essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician.

Failure to follow this advice may result

in electrical shock or death.

Important safety instructions!

To avoid hazard, follow these instructions carefully before installing or using this appliance. Please make this information available to the person installing the appliance - doing so could reduce your installation costs. This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations. Failure to install the appliance correctly could invalidate any

WARNING!

Fire hazard

Do not use adapters, reducers, or

branching devices to connect this appliance to the mains power supply.

warranty or liability claims.

Failure to follow this advice may result

If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

LOWER TRIM

OVEN DOOR

LOWER TRIM

AIR FLOW

E

N

L

1

(L )

2

E

N

L

1

(L )

2

Green & Yellow (Earth)

Brown (Live)

Blue (Neutral)

N

L

(2,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

3

PRIOR TO INSTALLATION

Before you install the oven, make sure that

the benchtop and oven cavity are square and level, and are the required dimensions the installation will comply with all clearance requirements and applicable standards and regulations a suitable isolating switch providing full disconnection from the mains power supply (under overvoltage category III conditions) is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements). the isolating switch will be easily accessible to the customer with the oven installed there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall the oven will rest on a surface that can support its weight the height from the floor suits the customer you consult local building authorities and by-laws if in doubt regarding installation.

Important!

Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cavity.

4

UNPACKING THE OVEN

Important!

Do not lift the oven by the door handle.

5

ELECTRICAL CONNECTION

Important!

This oven must be connected to the mains power supply only by a suitably qualified person. This oven must be earthed.

Before connecting the oven to the mains power supply, check that

the domestic wiring system is suitable for the power drawn by the oven

(as specified on the rating plate)

the voltage corresponds to the value given on the rating plate.

OB60S & OB60N MODELS

Model code Power Voltage

OB60SLC...

OB60SLM...

OB60SCE...

OB60SCM...

OB60SCT...

OB60SDT...

OB60S9D...

OB60SV...

OB60NL...

OB60NC...

OB60ND...

2350-2550 W 230 - 240 V~

3070 W 220-240 V~

3600 W 230 V~

3400 W 220-240 V~

3070 W 220-240 V~

2050 W 220-240 V~

2800 W 220-240 V~

1

Unhook to open cover

2

Unscrew to open

cable clamp

Remove all packaging and dispose of it responsibly. Recycle items that you can. Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the lower trim.

You may remove the feet, but ensure the oven does not sit on the lower trim

Important!

The lower trim ensures correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

OB60B & OB60D MODELS

Model code Power Voltage

OB60BC...

OB60BD...

OB60B77C...

OB60B77D...

OB60DD...

5800 W 220 - 240 V~

5850 W 220 - 240 V~

6120 W 220 - 240 V~

1

Unscrew to

remove cover

plate

2

D

(3,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(1,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

2

PRODUCT & CABINETRY DIMENSIONS

OB60S & OB60N MODELS

Installation diagrams for illustration purposes only

C

E

B

L

I

K

I

J

D

A

H

F

L

16-20 mm

G

2.5 mm

Product dimensions (mm)

A overall height* of product

B overall width of product

C overall depth of product (excluding handle and knobs)

D height of chassis

E width of chassis

F depth of chassis

depth of oven frame and control panel

G

(=distance between front of chassis and front of oven door, excl. knobs)

depth of oven door when fully open

H

control panel)

I minimum inside width of cavity

IIoverall width of cavity

J inside height of cavity

JIoverall height of cavity

K minimum inside depth of cavity

L flush fitting cabinetry clearance

Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s instructions.

*All height measurements include mounted feet.

(measured from front of

OB60S

597 450**

595 595

565 554

582 436

556 536

545 534

20 20

435 289

560 560

600 600

585 440**

600 455**

550 550

20 20

OB60N

OB60B & OB60D MODELS

C

B

E

A

L

H

D

I

H

F

G

Product dimensions (mm)

A overall height* of product

B overall width of product

C overall depth of product (excluding handle and knobs)

D height of chassis

E width of chassis

F depth of chassis

depth of oven frame and control panel

G

(=distance between front of chassis and front of oven door, excl. knobs)

depth of upper oven door when fully open

H

(measured from front of control panel)

depth of lower oven door when fully open

I

H

(measured from front of control panel)

I minimum inside width of cavity

IIoverall width of cavity

J inside height of cavity

JIoverall height of cavity

K minimum inside depth of cavity

L flush fitting cabinetry clearance

*All height measurements include mounted feet.

I

J

K

16-20 mm

L

2.5 mm

OB60B

888 1077

595 595

565 565

874 1057

556 556

545 545

20 20

261 435

435 450

560 560

600 600

877 1065

893 1082

550 550

20 20

OB60D

Unscrew to remove

(2,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

6

SECURING OVEN TO CABINETRY

1

Position the oven in the prepared cavity.

Important!

Do not lift the oven by the door handle.

2

Open the oven door fully.

3

Use the supplied screws to secure the oven to the cabinetry.

Important!

Do not over-tighten the screws. Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal.

FEET

2.5 mm

7

FINAL CHECKLIST

Make sure the oven is level and securely fitted to the cabinetry and the oven

door opens and closes freely.

Make sure all the internal packaging has been removed from the oven cavity.

Make sure all oven vents and openings are clear and are free of any

obstruction/damage. Check the lower trim is still undamaged - open the oven door slowly to its fully

open position and check if there is adequate clearance between the bottom of

the door and the lower trim. This is to ensure correct air circulation. Should the

lower trim become damaged, straighten the trim and ensure the oven door

opens fully without obstruction.

Check that the power supply cable does not touch any metal parts that can

become hot during use.

Make sure that the isolating switch is easily accessible by the customer.

Turn the power to the oven on. On some models, the display should light up and show 0:00.

Advise the customer to follow the instructions in their user guide in section

‘First use’.

cable clamp

(3,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(1,3) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

** If  tting the lower trim extension kit, the overall height of product (A) increases by 25 mm (to 475 mm). The height of the cavity (J and Ji) therefore needs to be increased by 25 mm also (to 465 mm and 480 mm respectively).

(2,3) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

www. sherpaykel.com F&P Italy Part No. 1103268-ß8 599790H NZ AU GB IE 10.17

(3,3) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

89

SECURE

THE

OVEN

TO

THE

CABINETRY

REFIT

THE

DOOR

(1,1) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

www. sherpaykel.com F&P Italy Part No. 1103268-ß8 599790H NZ AU GB IE 10.17

Turn the oven function dial back to OFF.

five minutes, open the oven door: the air inside should feel warm.

Repairer, or contact us through our local website, listed below.

the Service & Warranty book for warranty details and your nearest Authorised

If after checking these points you still need assistance or parts, please refer to

If a problem occurs, consult the Troubleshooting section of the User Guide.

Make sure the voltage is correct across all phases.

Make sure that power is being supplied to the oven.

Make sure that the electrical connections have been correctly made.

Check that the circuit breaker has not tripped or the fuse blown.

following:

If the appliance is not functioning correctly after installation, check the

of the oven. Inside the oven cavity, both oven lights should come on. After

Turn the oven function dial to ‘Bake’. Air should blow out of the vent at the top Turn the power to the oven on. The display should light up and show 0:00.

Make sure that the isolating switch is accessible by the customer.

Failure to make sure all oven vents are unobstructed may result in poor product performance.

Important!

obstruction/damage.

Make sure all oven vents and openings are clear and are free of any

Make sure all the internal packaging has been removed from the oven cavity.

oven door opens and closes freely.

Make sure the appliance is level and securely fitted to the cabinetry and the

TROUBLESHOOTING

4

x4

3

FINAL CHECKLIST

10 11

2

1

supplied scews

3 Secure oven to cabinetry using

control panel not pushing on the vents or

2 Push oven in, ensuring you’re

hands under the oven chassis

2 3

1

1 Lift from both sides placing

the door sensor lever trim of the oven or damage the upper Take care not to

(2,1) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

cooktop manufacturer’s instructions. Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the

H

depth of oven door (open) (measured from front of door) 418

G

depth of oven frame and control panel (excludes handle and dials) 20

F

depth of chassis 544

E

maximum width of chassis 853

D

overall height of chassis 468

C

height of cavity 480

B

overall width of cabinetry 900

I

B

minimum inside width of cavity 860

A

minimum inside depth of cavity 550

I

D

height of chassis at the rear 464

C

overall depth of product (excludes handle and dials) 564

B

overall width of product 895

A

overall height of product (including upper and lower vents) 478

OB90

models

Cabinetry dimensions (mm)

Ensure the cavity is completely sealed with no gaps

OB90

models

Product dimensions (mm)

2.5 mm

G

F

G

16-20 mm

H

D

I

C

A

E

B

A

C

B

I

CABINETRY DIMENSIONS

3

resulting from using the oven is easy to remove. Use easy-to-clean finishes for the wall surfaces surrounding the oven, so that cooking fume staining (near the top right corner of the oven seal). When handling the oven, take care not to damage the door sensor lever wooden blocks or similiar supports. Take extra care not to damage the lower trim of the oven. We suggest you place the unpacked oven onto Do not lift the oven by the door handle. Do not stand on the door, or place heavy objects on it. Make sure that the isolating switch will be easily accessible by the customer.

Installation diagrams for illustration purposes only

PRODUCT DIMENSIONS

2

from the side, top or bottom, but top entry must be at the rear of the cavity. cavity to at least 1.5 metres in front of the bottom edge of the opening. The cable may enter the cavity

the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the for this variation of the requirements). mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3 category III conditions) is incorporated in the permanent wiring, mounted and positioned to comply with

a suitable isolating switch providing full disconnection from the mains power supply (under overvoltage

the oven door can open fully without obstruction.

(3,1) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

89

SECURE THE OVEN TO THE CABINETRY

124 lb

56 kg

REFIT THE DOOR

(1,2) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

wiring correctly Terminate

PE N

L

Cable clamp

4

2

PE

5

N

3

L1

1

220-240 V ac

L2

open cover Unhook to

Unscrew

terminal block.

the cover plate behind the unscrew the screws fixing supply cable DO NOT To connect the power

Important!

given on the rating plate. the voltage corresponds to the value

(as specified on the rating plate) for the power drawn by the oven the domestic wiring system is suitable

mains power supply, check that Before connecting the oven to the

This oven must be earthed. qualified person. mains power supply only by a suitably This oven must be connected to the

Important!

mains power supply Connecting the oven to the

220-240 V 4730 W (20.56 A)

OB90 - NZ AU GB IE

prevents it being jammed between the cabinet wall and the rear of the oven. the cabinet cavity. This allows the power supply cable to sit inside the right rear of the oven and We recommend that the outlet for the power supply cable is located in the right rear corner of

Rating plate

ELECTRICAL CONNECTION HARD WIRING THE OVEN

67

4

cause serious injury.

Lifting unassisted may

product unassisted.

Do not attempt to lift this

2 3

1

Very Heavy

WARNING!

p

pp

y

p

g

(2,2) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

arts.

hot metal

ly cable will not touch an

ower su

Make sure that the Use the supplied screws to secure the oven to the cabinetry. Do not over-tighten the screws. Paykel will not cover the costs of removing the oven, or of damage caused by this removal. Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher &

When you install the oven

ht from the floor suits the customer.

the hei the benchtop and oven cavity are square and level, and are the required dimensions. the oven will rest on a flat surface that can support its weight. it will be lifted by two people.

Before you install the oven, please make sure that

similarly qualified person in order to avoid a hazard. replaced by the manufacturer, its service agent or If the power supply cable is damaged, it must be The oven must be earthed. warranty or liability claims. install the appliance correctly could invalidate any local building and electricity regulations. Failure to instructions and in compliance with any applicable qualified person according to these installation to the mains power supply only by a suitably This appliance must be installed and connected

WARNING!

Failure to follow this advice may result

appliance to the mains power supply. branching devices to connect this

Do not use adapters, reducers, or

Fire hazard

reduce your installation costs. person installing the appliance - doing so could Please make this information available to the before installing or using this appliance. To avoid hazard, follow these instructions carefully

in electrical shock or death.

Failure to follow this advice may result

qualified electrician. system must only be made by a

Important safety instructions!

Alterations to the domestic wiring system is essential and mandatory.

injury or cuts.

Failure to use caution could result in

Connection to a good earth wiring carrying out any maintenance or repairs. the mains power supply before

Take care - panel edges are sharp.

Cut hazard

Always disconnect the appliance from

Electrical shock hazard

WARNING!

NZ AU GB IE

WARNING!

SAFETY AND WARNINGS

1

website listed at the end of this document or contact your local Fisher & Paykel dealer. The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local

SAVE THESE INSTRUCTIONS

Important!

MULTIFUNCTION OB90 OVENS

(3,2) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

(1,3) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

UNPACK THE OVEN REMOVE THE DOOR

45

(2,3) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

INSTALLATION INSTRUCTIONS

(3,3) -2- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:33 PM

Fisher & Paykel OB60B77DEX3 Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual