Fisher & Paykel OB60B, OB60D Installation Instructions Manual

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our
local website listed at the end of this document or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS

1

WARNING!

Electrical shock hazard

Always disconnect the appliance from

the mains power supply before
carrying out any maintenance or repairs.
Connection to a good earth wiring
system is essential and mandatory.
Alterations to the domestic wiring
system must only be made by a
qualified electrician.

Failure to follow this advice may result

in electrical shock or death.

WARNING!

Fire hazard

Do not use adapters, reducers, or

branching devices to connect this
appliance to the mains power supply.

Failure to follow this advice may result

Important safety instructions!

To avoid hazard, follow these instructions carefully
before installing or using this appliance.
Please make this information available to the
person installing the appliance - doing so could
reduce your installation costs.
This appliance must be installed and connected
to the mains power supply only by a suitably
qualified person according to these installation
instructions and in compliance with any applicable
local building and electricity regulations. Failure to
install the appliance correctly could invalidate any
warranty or liability claims.
If the power supply cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in

injury or cuts.

NZ AU GB IE

MULTIFUNCTION OB60 OVENS

INSTALLATION INSTRUCTIONS

(1,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(1,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

LOWER TRIM

OVEN DOOR

LOWER TRIM

AIR FLOW

PRIOR TO INSTALLATION

UNPACKING THE OVEN

3

4

5

ELECTRICAL CONNECTION

Before you install the oven, make sure that

the benchtop and oven cavity are square and level, and are the required dimensions
the installation will comply with all clearance requirements and applicable standards and regulations
a suitable isolating switch providing full disconnection from the mains power supply (under
overvoltage category III conditions) is incorporated in the permanent wiring, mounted and positioned
to comply with the local wiring rules and regulations. The isolating switch must be of an approved
type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if
the local wiring rules allow for this variation of the requirements).
the isolating switch will be easily accessible to the customer with the oven installed
there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for
ease of installation and servicing
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall
the oven will rest on a surface that can support its weight
the height from the floor suits the customer
you consult local building authorities and by-laws if in doubt regarding installation.

Important!

Some environmental factors and cooking habits can cause condensation in and around the oven during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we
recommend moisture-proofing the oven cavity.

Important!

This oven must be connected to the mains power supply only by a suitably qualified person.
This oven must be earthed.

Before connecting the oven to the mains power supply, check that

the domestic wiring system is suitable for the power drawn by the oven

(as specified on the rating plate)

the voltage corresponds to the value given on the rating plate.

Important!

Do not lift the oven by the door handle.

Remove all packaging and dispose of it responsibly. Recycle items that you can.
Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the lower trim.

You may remove the feet, but ensure the oven does not sit on the lower trim

Important!

The lower trim ensures correct air circulation and allows the door to open and close without obstruction. The
manufacturer does not accept any responsibility for damage resulting from incorrect installation.

OB60B & OB60D MODELS

OB60S & OB60N MODELS

Model code Power Voltage

OB60SLC...

2350-2550 W 230 - 240 V~

OB60SLM...

3070 W 220-240 V~

OB60SCE...

3070 W 220-240 V~

OB60SCM...

3070 W 220-240 V~

OB60SCT...

3600 W 230 V~

OB60SDT...

3600 W 230 V~

OB60S9D...

3400 W 220-240 V~

OB60SV...

3070 W 220-240 V~

OB60NL...

2050 W 220-240 V~

OB60NC...

2800 W 220-240 V~

OB60ND...

2800 W 220-240 V~

Model code Power Voltage

OB60BC...

5800 W 220 - 240 V~

OB60BD...

5800 W 220 - 240 V~

OB60B77C...

5850 W 220 - 240 V~

OB60B77D...

5850 W 220 - 240 V~

OB60DD...

6120 W 220 - 240 V~

E

N

L

1

(L )

2

Unhook to open cover

1

2

Unscrew to open

cable clamp

E

N

L

1

(L )

2

Green & Yellow
(Earth)

Brown (Live)

Blue (Neutral)

N

L

D

1

2

Unscrew to

remove cover

plate

(2,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(2,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(3,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(3,1) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

2

PRODUCT & CABINETRY DIMENSIONS

Product dimensions (mm)

OB60S

OB60N

A overall height* of product

597 450**

B overall width of product

595 595

C overall depth of product (excluding handle and knobs)

565 554

D height of chassis

582 436

E width of chassis

556 536

F depth of chassis

545 534

G

depth of oven frame and control panel

(=distance between front of chassis and front of oven door, excl. knobs)

20 20

H

depth of oven door when fully open

(measured from front of

control panel)

435 289

I minimum inside width of cavity

560 560

IIoverall width of cavity

600 600

J inside height of cavity

585 440**

JIoverall height of cavity

600 455**

K minimum inside depth of cavity

550 550

L flush fitting cabinetry clearance

20 20

Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop
manufacturer’s instructions.

*All height measurements include mounted feet.

Product dimensions (mm)

OB60B

OB60D

A overall height* of product

888 1077

B overall width of product

595 595

C overall depth of product (excluding handle and knobs)

565 565

D height of chassis

874 1057

E width of chassis

556 556

F depth of chassis

545 545

G

depth of oven frame and control panel

(=distance between front of chassis and front of oven door, excl. knobs)

20 20

H

depth of upper oven door when fully open

(measured from front of control panel)

261 435

H

I

depth of lower oven door when fully open

(measured from front of control panel)

435 450

I minimum inside width of cavity

560 560

IIoverall width of cavity

600 600

J inside height of cavity

877 1065

JIoverall height of cavity

893 1082

K minimum inside depth of cavity

550 550

L flush fitting cabinetry clearance

20 20

*All height measurements include mounted feet.

OB60S & OB60N MODELS

Installation diagrams for
illustration purposes only

2.5 mm

16-20 mm

A

C

E

D

F

G

H

J

K

L

L

I

I

I

J

I

B

2.5 mm

16-20 mm

L

A

C

E

D

F

G

H

H

I

J

K

L

I

I

I

J

I

B

OB60B & OB60D MODELS

(1,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(1,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

FEET

SECURING OVEN TO CABINETRY

6

1

Position the oven in the prepared cavity.

Important!

Do not lift the oven by the door handle.

2

Open the oven door fully.

3

Use the supplied screws to secure the oven to the cabinetry.

Important!

Do not over-tighten the screws.
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult.
Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal.

Unscrew to remove

cable clamp

2.5 mm

Make sure the oven is level and securely fitted to the cabinetry and the oven

door opens and closes freely.

Make sure all the internal packaging has been removed from the oven cavity.

Make sure all oven vents and openings are clear and are free of any

obstruction/damage.
Check the lower trim is still undamaged - open the oven door slowly to its fully

open position and check if there is adequate clearance between the bottom of

the door and the lower trim. This is to ensure correct air circulation. Should the

lower trim become damaged, straighten the trim and ensure the oven door

opens fully without obstruction.

Check that the power supply cable does not touch any metal parts that can

become hot during use.

Make sure that the isolating switch is easily accessible by the customer.

Turn the power to the oven on. On some models, the display should light up
and show 0:00.

Advise the customer to follow the instructions in their user guide in section

‘First use’.

7

FINAL CHECKLIST

(2,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(2,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(3,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM

(3,2) -1- 599790H OB60&OB90 installA2 NZGB.indd 25/09/17 12:32 PM