Fisher Paykel OB24SDPTX1, OB24SDPTB1, OB24SDPTDB1, OB24SDPTDX1 Installation Manual

BUILT-IN OVEN

OB24SDPT models

INSTALLATION GUIDE

US CA

591944A 07.19

SAFETY AND WARNINGS

WARNING!

Electric Shock Hazard

Failure to follow this advice may result in electric shock or death.

• Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply.

• Connection to a good ground wiring system is absolutely essential and mandatory.

• Alterations to the domestic wiring system must only be made by a qualified electrician

WARNING!

Fire Hazard

Failure to follow this advice may result in overheating, burning, and injury.

• Do not use adapters, reducers, or branching devices to connect this appliance to the mains power supply.

WARNING!

Cut Hazard

Failure to use caution could result in injury.

• Take care: some edges are sharp.

WARNING!

To avoid hazard, follow these instructions carefully before installing or using this appliance.

Please make this information available to the person installing the appliance—doing so could reduce your installation costs.

Save these instructions for the local inspectors use.

This oven is to be installed and connected to the electricity supply only by an authorized person.

If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the socket cable section is suitable for the electricity drawn by the oven.

The oven must be grounded.

Installation must comply with your local building and electricity regulations.

This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations. Failure to install the appliance correctly could invalidate any warranty or liability claims.

If the power supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

A circuit breaker is recommended.

Do not use adaptors, reducers or branching devices to connect the oven to the mains electricity supply, as they can cause overheating and burning.

Make sure the cavity is completely sealed with no gaps. This is to ensure the oven cooling system functions correctly.

The appliance must not be installed behind a decorative door in order to avoid overheating.

Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

Electrical requirements

Connect oven with copper wire only.

Do not cut the conduit.

A U.L. listed conduit connector must be provided at the junction box.

Do not ground to a gas pipe.

Do not have a fuse in the grounding or neutral circuit.

Fuse both sides of the line.

A time delay fuse or circuit breaker is recommended. If using a time delay fuse, then fuse both sides of the line.

Flexible armored cable from the appliance should be connected directly to the junction box.

Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire).

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path and wire gauge are in accordance with local codes.

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

PARTS SUPPLIED

Screws (2) Metal side shelves

fixing nut (2)

PRIOR TO INSTALLATION

Ensure that:

the countertop and oven cavity are square and level, and are the required dimensions

the installation will comply with all clearance requirements and applicable standards and regulations

the isolating switch will be easily accessible to the customer with the oven installed

the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening

the cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity

the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall

the oven will rest on a surface that can support its weight

the height from the floor suits the customer

you consult local building authorities and by-laws if in doubt regarding installation

IMPORTANT!

Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cavity.

AFTER INSTALLATION

Ensure that:

the oven door can open fully without obstruction

the oven is not sealed into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this removal

the power supply cable does not touch any hot metal parts

the isolating switch is easily accessible to the customer with the oven installed

you complete the ‘Final checklist’ at the end of the installation

If, after following the guidance given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel trained and supported service technician, Customer Care, or contact us through our website fisherpaykel.com

PRODUCT DIMENSIONS

FRONT

PLAN

PROFILE

PRODUCT DIMENSIONS

A Overall height of oven

B Overall width of oven

C Overall depth of oven (excluding handle and dials)

D Height of chassis

E Width of chassis

F Depth of chassis

G Depth of oven frame and control panel (distance between front of chassis and

front of oven door, excl. handle and dials)

H Depth of oven door when fully open (measured from front of control panel)

OB24SDPT MODELS

INCHES MM

23 9/16 598

23 7/16 596

22 1/4 565

22 5/8” 575

21 7/8 556

21 7/16 545

13/16 20

18 1/8 460

CABINETRY DIMENSIONS

PROFILE PLAN

CABINETRY DIMENSIONS

A Minimum inside width of cavity

OB24SDPT MODELS

INCHES MM

21 1/16 560

PROUD INSTALL

5/8 - 13/16” (16-20mm)

FLUSH INSTALL

5/8 - 13/16” (16-20mm)

B Overall width of cabinetry

C Minimum inside height of cavity

D Overall height of cabinetry

E Minimum inside depth of cavity

23 5/8 600

22 13/16 580

23 5/8 600

21 5/8 550

If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manufacturer’s instructions.

min. 1/16” (2mm)

DISCARD PACKAGING RESPONSIBLY

Remove the accessories box from the top of the oven and set aside.

Recycle responsibly.

+ 14 hidden pages