
Safety and warnings
Operating instru_;tions
(ontrois (modelb witls irsoIL,,£D)
Controls (modells witlh IL,£D)
Wash program chart
Caring for your dinnerware
Dishwasher standards test
Loading suggestions
Detergent dispenser
Water softener
Rinse agent dispenser
Option adjustments
User maintenance instructions
Fault €:odes
Warranty and service
6
8
10
11
12
13
14
16
18
20
22
23
26
29
31
34
SAVE THESEINSTRUCTIONS
The r_o(/e/ hovvn it:, this User (}uid_ _r_y M,ot _,ge_vc4i/_tg/ein _// r_rke_ _t';,d_/#e
subject to chonge 08shy time. for current de_c_i/sshout mode/sad spedifmotk)n
ovdbi/obi/ity it:,your tour}itS p/eo e visit out_/oco/websitm/istmd on the book covet'
ot' con tc;c8yout' Iocol fishmt'& P#ykeldmolm_


Safety and warnings
}'our DishDrawer has been carefully designed to operate safely during normal dishwashing
procedures, Please keep the following instructions in mind when you are using your
DishDraweP.
WARNINGf _When using },our dishwashe8 follow bas£ precautions, including the following:
Read aft instructions before using the DishDrawert
The information in this manual must be followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or loss of life.
" Use the DishDraw, er ®only for its intended function as described in this user guide,
Use only detergents or Nnse agent recommended for use in a domestic dishwasher and keep
them out of reach of children, Check that the detergent dispenser Lsempty after the completion
of each wash program.
When loading items to be washed, locate sharp items so that they are not likely to damage the
lid seal and load sharp knives with the handle up to reduce the risk of cut4ype i?_juNes,
Do not touch the heater plate during or immediately after use,
Do not operate your DishDrawer ®unless aH enclosure panels are properly in place,
Do not tamper with the controls,
Do not abuse, sit on, stand in or on the drawer or dish rack of the DishDrawer ®.
The adjustable racks are desoned to support cups, glasses and kitchen utensils, When the
adjustable racks are in the DishDrawer ®do not lean on or use them to support your body
weight,
To reduce the risk of injury, do not allow children to play in or on the DishDrawer ®.
Under certain conditions, hydrogen gas may be produced in a hot water heater system that has
not been used for two weeks or more, HYDROGEN GAS IS EXPLOSIVEo If the hot water system has
not been used for such a period, before using the dishw, ashe_ turn on all hot water faucets and
let the water flow from each for several minutes, This v_,,fltrelease any accumulated hydrogen
gas, As the gas is flammable, do not smoke or use an open flame duNng this time,
Remove the door to the washing compartment when removing an old dishwasher from service
or discarding it,
Dishwasher detergents are alkaline. They can be dangerous ff swaflowedo Avoid contact with
skin and eyes, keep children and infirm persons away from the dLshv_,asher when the drawer is
opened.

Safety and warnings
installation
This DishDrawer ®must be installed and located in accordance with the Installation k_structions
before it L_used. ff you did not receive fnstafiation k_struction sheets with your DishDrawer% you
can order them by calling your Authorized Service Agent or from the Fisher & Paykel website,
wwv_fisherpaykeLcom,
Installation and service must be performed by a qualified technician.
, ff the power supply cord is damaged, it must be replaced by a dealer or A uthoMzed Service Center
or a similar qualified trades person in order to avoid a hazard,
Ensure the DishDrawer ®Lssecured to adjacent cabinetu using the brackets provided, Failure to
do so may result in an unstable product, which may cause damage or k_juu,
Do not operate this appliance ff it is damaged, malfunctioning, partially disassem bled or has
missing or broken part._ including a damaged power supply cord or plug,
Do not store or use petrol or other flammable vapors and liquids in the vidnity of the
DishDrawer%
Connect to a properly rate4 protected and sized power supply circuit to avoid electrical overload,
Make sure that the power supply cord LSlocated so that it wilt not be stepped on, tripped over or
otherwise subject to damage or stress,
Do not install or store the DishDrawer ®where it will be exposed to temperatures below freezing
or exposed to weather°
Do not use an extension cord or a portable electrical outlet devke (e.g. multi-socket outlet box)
to connect the DishDrawer ®to the power supply.
This appHance must be grounded, ln the event of a matfunction or breakdown, grounding wHI
reduce the risk of electric shock by providk_g a path of least resistance for electric current, This
appliance Lsequipped with a cord having an equipment-grounding conductor and a grounding
plug, The plug must be plugged into an appropriate outlet that is installed and grounded
in accordance with all local codes and ordinances, WARNING - Improper connection of the
equipment-grounding conductor can result in a risk of electric shock, Check with a qualified
electrician or service representative if you are in doubt as to whether the apph%nce L_properly
grounded. Do not modit_v the plug provided with the appliance;: ff it will not fit the outlet, have a
proper outlet k_stalted by a quahWed technician,
ff the DishDrawer® is instaHed as a permanently connected appliance:
GROUNDING INSTRUCTIONS - This apph%nce must be connected to a grounded metal permanent
wiring system, or an equipment-grounding conductor must be run with the cffcuit conductors
and connected to the equipment-grounding terminal or lead on the appliance,

Safety and wamings
Maintenance
Do not repair or replace any part of the apph'ance or attempt any serv£ing unless specificaNy
recommended in this user guide. We recommend that you carl an Authorized Service Agent°
Keep the floor around your appliance dean and dry to reduce the possibility of stippingo
Keep the area around/underneath your appliance free from the accumulation of combustible
materials, such as h'nt, paper, rags and chemicMs°
When cleaning the undersMe of the fi#er plate, care must be taken on the sharp outer edge to
avoid the risk of cut type _jurieSo
Under no circumstances should you open the drawer whilst the Di@Drawer _i_in operation°
Always press the HI button to pause and wait until you hear the three additional beeps before
opening the drawer.
The DishDrawer ®must be used with the motor assembly, tiger plate, drain fi#er and spray arm in
place°
When disconnecting the appiiance puH the plug rather than the power suppiy cord or junction of
cord to avoid damage°
Take care when toading the DishDrawer ®not to load dishware items so they prevent the lid #om
pr@edy seah'ng with the drawer° items should be placed so they do not protrude above andl/or
forced into the drawe_ otherwise a service carl may resu#.
Household app#ances are not #_tended to be played with by children° Children or persons with a
disab##y which Hm#s the# abi#ty to use the appliance, should have a responsible person #_struct
them in i% use° The instructor should be satisfied that they can then use the appliance without
danger to themselves or their surroundings°
Close supervision i._necessary ff this appliance iS used by or near children° Do not allow children
to play inside, on or with this appliance or any discarded apph'ance°
ira dishwasher deaner is used, we would strongty recommend a wash program with detergent
should be run immediately a#erward, to prevent any damage to the DishDrawer®.
The DishDrawer _ i._designed for wash#_g normM household utensils° items that are
contaminated by petrol, paint, steel or iron debris, corrosive, acidic or MkMine chemicMs are not
to be washed in the DishDrawer®°
If the DishDrawer ®is not being used for long periods of time, turn the electfidty and water supply
to the DishDrawer ®off.
Do not pour detergent or rinse agent into the sMt reservoir. The detergent or rinse agent will
destroy the water so#ener.

O_@_&ting instructions _ Contr©_s (modeB with no LCD}
If you have a double DishDrawer% each drawer has its own controls and can run independently
of the other.
Power button @
The @ button turns the DishDraweP_on oroff, Opening
the drawer will automatically turn the DishDraweP_on for
30 seconds, To end a wash program in mid cycle, press
the O button, Any water in the DishDraweP_will be
pumped out.
Start/Pause button _H
The bl_ button starts a wash program, Press the HI
button to pause or restart the DishDraweP _during a wash
program. When paused, wait for three beeps before
opening the drawer, Forcing the drawer open while in mid
cycle may cause damage or injury,
o o
Delay start
The b_lbutton also setsthe Delaystart feature which can delay the start of a wash program from
1to 12 hours.
To activate De_ay start
1 Press and hold the IH_ button until the light above the bll button turns orange (or purple,
depending on your model),
2 Continue holding the bH button down until the desired delay time has been reached, The
DishDraweP will emit audible'beeps'as you hold the bH button down, each beep indicates
another hour delay,
s The DishDraweP _will start once the delay time has elapsed and the drawer is closed.
To cancel Delay start
Press the (D button,
Lock button _/@ (optional}
The _/@ button activates/deactivates the Keylock or the Childlock functions.

Operating instructions - ControB {mode swithnoLCD)
The Keylock feature disables all the buttons on the DishDraweP.
To activate, press and hold the _/@ button until you hear one beep (3 seconds), The light
above the _/@ button is lit when Keylock is activated.
To cancel the Keylock feature, press and hold the _/@ button until the light above the _/@
button disappears,
Chi[d[ock
The Childlock feature locks the drawer and disables all the buttons.
To activate, press and hold the _/@ button until you hear two beeps (5 seconds). The light
above the _/@ button is lit when Childlock is activated.
To cancel the Childlock feature, press and hold the _/@ button until the light above the
_/@ button disappears,
Wash program selector
Press the _ button to select a wash program. The D[shDraweP w[[[ remember the last program
used.
ECO ,
Eco button Eco (optional)
Press the 8CO button if you would like the wash program to use less energy. The red ECO light
wiI[ indicate the feature is om If your dishes are heavily soiled or you require enhanced dry
performance, we do not recommend ECO programmes,
Power faiJure
[f the DishDrawer _ is operating and a power failure occurs, it will stop. The DishDrawer _ may be
unable to be opened during this time When the power supply is resumed, the DishDraweP will
restart in the same part of the wash program,

O_@_&ting inStruCtiOnS _ Contr©_s (modeB with LCD}
If you have a double DishDrawer% each drawer has its own control panel and can run
independently of the other.
Wash program Time Fault symbols - see'Fault
progress symbol remaining codes' if they appear
Salt reservoir is empty
(DD24-H models only)
oKeylock or Childlock is
activated
Delay start symboJ
Power Start/Pause Lock button
button button
Power button ©
The tD button turns the DishDraweP on or oE Opening the drawer will automatically turn the
DishDraweP on for 30 seconds, ]:o end a wash program in mid cycle, press the O button. Any
water in the DishDrawer _'_will be pumped out.
Start/Pause button _ll
The _1_button starts a wash program, Press the bll button to pause or restart the DishDraweP
during a wash program, When paused, wait for three beeps before opening the drawer. Forcing
the drawer open while in mid cycle may cause damage or injury.
Delay start
The _t button also sets the Delay start feature which can delay the start of a wash program from
1 to 12 hours,
To activate De_ay start
1 Press and hold the _H button until the delay symbol Q appears on the electronic display.
2 Continue holding the bll button down until the desired delay time has been reache&
s The DishDraweP will start once the delay time has elapsed and the drawer is closed.
To cance_ Delay start
Press the O button.
Lock button @ (optional}
The @ button activates/deactivates the Ke}4ock or the ChikJlock functions.

Operating instructions - Controls {mode sw thLCD/
Keybck
[he Keylock feature disables all the buttons on the control panel
To activate, press and hold the _ button until you hear one beep (3 seconds). The _ symbol
appears in the electronic display when the Keylock feature is activated.
Childbck
The Childlock feature locksthe drawer and disables all the buttons on the control panel,
Toactivate, press and hold the @ button until you hear two beeps(5 seconds), The @ symbol
appears in the electronic display when the Childlock feature isactivated,
To cancel the Childlock feature, press and hold the @ button until you hear one beep and the
@ symbol disappears from the electronic display.
Wash program selector
Press the _ button to select a wash program. The DishDraweP will remember the last program
used.
( ECO
//
Eco button ECO(optional)
Press the££o button if you would like the wash program to use less energy, The red ECO light
will indicate the feature is on, If your dishes are heavily soiled or you require enhanced dry
performance, we do not recommend KO programmes.
Wash program progress symboJs
As the wash program advances through the cycle, the following symbols will appear in
the electronk display to indicate the progressiom When a wash program has started, the
electronic display also will count down the time remaining in one minute increments,
Drty Pre Wash Man Wash Post Rinse Drying Clean
Power failure
If the DishDraweP _is operating and a power failure occurs, it will stop, The DishDraweP _may be
unable to be opened during this time When the power supply is resumed, the DishDraweP will
restart in the same part of the wash program.

Operating instructions - Operation
1 Load dishes
Remove all food scraps and load the dishes.
2 Add detergent
S Check rinse agent
4 Press the _ button
5 SeJect a wash program
The length of the wash program will appear
on the electronic display (models with LCD
only).
6 SeJect ££O(optionat}
7 Check
Ensure there is nothing obstructing the
spray arm. The drain filter must be level with
the filter plate.
2
3
8
Start
Close the drawer and press the H_ button.
9
Finish
The DishDraweP _will beep six times to
indicate the end of the wash program. At
the end of the wash program the drying fan
will continue to run for a set time or until the
drawer is opened. The fan assists with drying
and uses negligible amounts of energy. It
is normal for some water to remain in the
drain filter area after the wash program is
complete.
Double models only: At the end of a wash
program, you may find both drawers
draining simultaneously. This is normal.

Wash program chart
Heavy Normal Fast DeJicate Rinse
Heavily soiled Disheswith Lighdy soiled Lightly soiled and Preventsodorsand
pots,pans and noh'_Talsoils dishes, heat sensitive soilsdrying on dishes.
dishes, fbr optimum crockery.
washanddry
performance,
pre--wash 1 pre--wash 1 pre--wash pre--wash
pre wash 2 pre--wash 2
main wash 150°F main wash 140°F main wash 130°F main wash 120°F
post-rinse 1 post-rinse post-rinse post-rinse
post--rinse 2
final rinse 163°F final rinse 140°F final rinse 120°F final rinse 130°F
drying phase drying phase drying phase
liS!
Heavy Normat Fast Delicate
Heawttysoiled Normal soiled Lighdy soi/e4 non Lightly soile4
everydaydishes, dishesfor greasydishes, non greasyand
optimum energy heat sensitive
use. crockery.
pre--wash 1 pre--wash pre--wash
pre--wash 2
main wash 150°F main wash 130°F main wash 115°F main wash 115°F
post--rinse 1 post-rinse post-rinse post-rinse
posbrinse 2
final rinse 150°F final rinse 130°F final rinse 115°F final rinse 120°F
drying phase drying phase drying phase
Note:
Wash times can vary depending on the incoming water temperature, ambient conditions, type
of dish load and whether the drawer has been opened during the wash. Wash times are only
APPROXIM£TE on the electronic display and based on 120°F incoming water.

Caring for your dinnerware
The combination of high temperatures and dishwasher detergent may cause damage to some
items if they are washed in the DishDrawePL Remember, if in any doubt about any aspect
concerning items washed in the DishDrawer _'_,follow the instructions from the manufacturer of
the items, or wash the item by hand.
Cudery & silverware
AHcutlery and silverware should be rinsed immediately after use to prevent tarnishing caused by
some foods. The Rinse wash program is useful for this. Silver items should not come into contact
with stainless steel, eg other cutlery. Mixing these items can cause staining. Remove silver cutlery
from the DishDrawer _'_and hand dry it immediately after the program has finished.
Aluminum
Aluminum can be dulled by dishwasher detergent. The degree of change depends on the
quality of the product.
Other metals
Iron and cast iron objects can rust and stain other items. Copper, pewter and brass tend to stain.
Woodware
Wooden items are generally sensitive to heat and water. Regular use in the dishwasher may
cause deterioration over time. If in doubt, wash by hand.
Glassware
Most everyday glassware is dishwasher safe Crystal, very fine and antique glassware may etch
that is, become opaque. You may prefer to wash these items by hand.
Plastic
Some pBtic may change shape or color with hot water. Check manufacturer's instructions
about washing plastic items. Washable plastic items should be weighed down so they do not
flip over and fi[[ with water or fall through the base rack during the wash.
Decorated items
Most modern china patterns are dishwasher safe. Antique items, those with a pattern painted
over the glaze, gold rims or hand painted china may be more sensitive to machine washing. If in
doubt, wash by hand.
Glued items
Certain adhesives are softened or dissolved in machine washing. If in doubt, wash by hand.
Vacation time
If the DishDraweP _is not going to be used for some time, we recommend you leave the
DishDraweP _dean and empty. Leave the drawers ajar to allow air to circulate. Turn off both the
power and water supply to the DishDrawer_L

Dishwasher standards test
The DishDrawePs are tested to various standards for both wash and dry performance,
The following are loading pattern diagrams, detergent quantities and rinse agent quantities used
for the DishDraweP.
Detergent quantities 5g (pre-wash) per drawer
lOg (main wash) per drawer
Water softener setting
(for DD24-H modeB onRy)
Recommended loading pa_em
Adjust the water softener to match the water
hardness_ Refer to the'Water softener' and
'Option adjustment' section.
Top (_rawer
1 2 3
Bottom drawe_
4 5 6

Racking features
Cudery basket
Mix spoons, knives and forks within each section to
stop cutlery nesting together.
Most cutlery is placed with the handle pointing
down.
For your safety, knives and sharp utensils should
have their handles up.
Small light items like baby bottle teats are best
placed under the anti-nesting grids to prevent
them from being displaced.
Stemware
notches
The six notches
on the left--
hand side
help support
long-stemmed
g lasswa re.
Folding tines
The front half is ideal for large, deep bowls.
Fold the tine sections down towards each other if you need the space for pots or other large
items.
Fold down the right-ohand section only and lean cups against the updght tines for extra stability.

Backing features
AdjustaNe racks
You can adjust these independently of each other to any height:
1 Fold up to unlockthe rack.
2 Adjust the height to suit by sliding up or down.
S Fold down to lock in position.
Fold the racks away if you need the space.
1 2 3
Glass supports
These clip on the rack
wires to give your tail
glasses extra stability.
'S[ideoar_dofo[d'
tines
Slide a[[ the way to the
left to fit larger dinner
plates.
Fold the tine sections
down towards each
other if you need the
space for pots or other
large items.

Loading suggestions
When [oading your DishDrawer, make sure that
you place items so that water coming from the rotating spray arm below can reach all areas
(performance wiI[ be reduced if it can't)
nothing blocks the water from getting to items on the adjustable racks
you place bowls and pots with their openings facing down
plates do not nest together,
Typical breakfast bad
Typica[ dinner party bad
Typica[ heavy bad

HowNOTtoloadyourDishDrawe¢_)
Loading suggestions
l!!{!ii!Sliiii!!ili!!i
Overcrowded and washwater will not
reachsome of the dinnerware,
Cups,glassesand bowls must have their
openings facing down.
Ensure dishware items are not forced
into or protrude out of the drawer as it
may prevent the lid from properly sealing
which could result in a service ca&
Locate sharp items safely to prevent
iniuring the user and damaging the lid
assembly,
Checkthe bottom of the cutlery basket to
ensure sharp or pointed items have not
come through as they may stop spray arm
rotation,
The plates are nesting together and wash
water may not get througL
Ensure cutlery are not nesting or stuck
together, They need to be evenly spread
out.
Ensure cutlery has not fallen through the
base rack and stopped the spray arm from
rotating.
The large bowl is blocking wash water
reaching the adiustable racks,
Large utensils should be on the adjustable
racks so they do not become dislodged and
stop the spray arm from rotating,
Sharp or pointed items must be placed
horizontally or with sharp edges/points
facing down to avoid risk of injury.

Detergent dispense
OMy use powdered detergent recommended for domestic automatic dishwashers in the
detergent @:spenser°
Dishwasher detergents are strongly a&ah_ne and can be dangerous ff swMtowedo
Avoid contact with skin and eyes°
Keep chiMren and infirm persons away#om the DishDrawer ® when the drawer is open.
Check that the detergent receptacle iS empty after completion
of the wash cycle°
We do not recommend using dishwasher tablets a,b --
in the DishDrawer®°
Do not place dishwasher tablets in the e --
detergent dispenser°
Detergent and dishwasher tablets should not
be in direct contact with dishes or cuderyo
Liquid detergen% are not suitable to be used in
the DishDrawer®°
Hand washing Hquids, soap, Jaundry detergents
or disinfectan% will damage the DishDrawert
Filling the detergent dispenser
Closed detergent dispenser
1 Press the latch down and the door wi[[ open.
2 Pour in detergent. No detergent is needed for the Rinse
program,
s After filling the main wash compartment, close the dispenser
door until it dicks shut, The detergent will automatically be
released into the DishDraweP during the wash program.
Open detergent dispen er
a Pre-wash compartment,
lOg / 2 teaspoon capacity
b Main wash compartment,
30g / 6 teaspoon capacity
c Detergent dispenser latch
d Rinse agent indicator light
e Rinse agent plug

Detergent dispense
Detergent quantities
The detergent quantities recommended beRoware for individuaRdrawers.
Hard
(>150ppm or >ggpg)
Medium (100-150ppm or 6-9gpg) AlP
Soft (<100ppm or <6gpg) Heavy
_ No detergent is required in the pre wash compartment for the Fast wash program.
Hard water situations
If you live in a hard water situation, we
recommend the installation of a household
water softener to improve the water quality,
detergent effectiveness and prevent the
buiIdoup of calcium deposits on dishes and
in the DishDraweP,
Certain brands of dishwasher detergent
contain varying quantities of phosphates,
which help soften water. We suggest
you use a detergent with high phosphate
content to improve the wash. The detergent
compartments need to be completely FULL
and rinse agent is used with its setting fixed
at 5.
We recommend the use of a dishwasher
cleaner/descaler whenever you notice
a buildoup of calcium deposits in your
DishDraweP.
AR_
i
Normal
Delicate
2
2
1
1
Soft water situations
If you live in an area of naturally soft water
or your household water is softened,
avoid using too much detergent in your
DishDrawePL An excess amount of detergent
is very aggressive on glassware and may
cause irreversible etching.
Etching is a chemical deterioration that
occurs on the surface of glassware when
it is subiected to high temperatures, too
much detergent and/or soft water situations.
Etching is caused by a combination of very
hot water, which causes the detergent to
become very aggressive, but because the
water is soft, there are no water hardness
mineral ions for the detergent to bind to,
so it extracts mineral ions directly from the
g[ass_
Etching looks like rainbow<olored film, as
the glassis subiected to further washing the
After you have used the dishwasher
c[eaneridesca[er you must run another
wash program with detergent to prevent
damage to the DishDrawer_L
surface will eventually appear opaque, This
type of etching isirreversible,
To prevent further etching from occurring
on glassware, use less detergent (follow the
recommended detergent quantities in the
user guide for soft water situations), and
ensure the DishDraweP is not overloaded,
so water can reach all the dishes during the
wash.
6
4
3
2
s
1

Wate s©ftene (©©24,_H modeB on_y)
Setting up the water softener
Using hard water (above 100ppm) for dishwashing can be detrimental to the performance of
your DishDraweP, Glasses will become opaque and dishes will become spotted or covered in a
white film,
Determine the water hardness in your Iota[ area
Your local water company wi[[ be able to provide you with information. Identify the setting you
require for your DishDraweP from the water hardness table below, For example, if your water
hardness is 500ppm, then the water softener setting on your DishDraweP should be four. Refer
to the 'Option adjustments' section to adjust the water softener sothat the setting corresponds
to your water hardness.
0
1
2
3
4
5
Note:
If },'our water hardness is above 625ppm, we highly' recommend you completely fill the
detergent compartment for all programs except Rinse and the rinse agent setting be at 5, If your
water hardness is above 625ppm, the wash performance of your DishDraweP will decline,
You may hear some unusual noises when the water softener is in operation, this is normal.
0-6
6--14
14-20
20-26
26-32
32-36
0-100
100-250
250-350
350-450
450-550
550-625
How to fill the salt reservoir
'I
Open the DishDraweP,
2
4
S
the salt reservoir, run a Rinse program to remove any salt
water or spilt granules,
Note:
When filling the salt reservoir, you may notice water being
displaced from the water softener
overflow.
container
Salt

Water softener (DD24, Hmode son y)
The watersogenermustalwa_sbe filledwithgranularsaltmade espedaIlyford_:shwasherwater
so_ening systems° Wedo not recommend the useof cooking satt like ruble satt, rock satt or
pallets as they may contain impurities that w_"Nimpair or diminish the byeof the water so_ene_
The salt reservoir
Water softening can only take placewhen there
issalt in the reservoir. The salt reservoir must
be filled prior to using the DishDraweP and
whenever the salt reservoir indicator light is red.
If the salt indicator light is red, the salt reservoir is
empty.
If the salt indicator light is Mack, there is enough salt in the
reservoir for the wash program that has been selected.
Models with LCD only: The electronic display will
also indicate when the salt reservoir is empty by
displaying the salt _ symbol.
a Salt indicator light
b Salt reservoir cap
Do not pour deteLqent or rinse agent into the satt
reservoir° Detergent and rinse agent wH_destroy
the water so_enero
Salt only
NO Detergent NO Rinse Agent

Rinse agent dispenser
We highly recommend the regular use of liquid rinse agent to give the best drying results.
Rinse agent gives a streabfree, sparkling clean Iookto glass and chinaware. In addition, it
prevents metal from tarnishing. The rinse agent dispenser is on the inside of the drawer, located
underneath the detergent dispenser. The rinse agent dispenser holds approximately 1.7fl oz (50
ml) of rinse agent.
Fillingthe rinse agent dispenser
1 Turn the plug counter-clockwise and remove.
2 Pour the rinse agent into the circular opening.
s Fake care not to spill rinse agent into the
DishDrawer% Any spillages must be wiped up to
prevent excess foaming. Failure to wipe rinse agent
spilhges may result in a service call which will not be
covered by warranty.
4 Fit the plug back into the original position.
How much rinse agent to use
The regulator may need adjusting to suit your water conditions. The lowest setting is'1'and
the highest is'5'. Refer to the 'Option adiustments' section to adiust the rinse agent setting. If
there is excessive foam at the end of the wash, red uce the setting. If dishes are wet or streaky
after drying, increase the setting.
Rinse agent indicator light
If the rinse agent indicator light is red, refill the dispenser. If the rinse agent indicator light is
dimly lit or not lit at all, there is enough rinse agent for the wash.
Note:
Lighter colored rinse agents will not dim the indicator light as effectively as darker colored rinse
agents.
When the rinse agent is being dispensed, you may notice some unusual noises during the wash:
this is normal.

Option ad ust ' ents
The following options can be adjusted to suit your preferences:
Rinse agent setting
Reduce the Rinse agent setting if there is excess foam after a wash program,
Increase the Rinse agent setting if dishes are wet or streaky after a wash program.
Water softener setting (DD24°H models only)
Refer to the 'Water softener' section,
Auto power setting
By default, DishDraweP _will automatically turn on whenever the drawer is opened. Washing will
not start until the drawer is dosed and the }H button has been pressed. If you do not want the
DishDrawer _'_to turn on automatically, this feature can be turned off.
End of wash program beeps
By default, DishDraweP _will beep six times at the end of a wash program. This feature can be
turned off.
Closed drawer option
The Closed drawer option will lock the DishDraweP _when the drawer is dosed, When you wish
to open the drawer, press the @ button. When the drawer is fully dosed again, the lid will
automatically come down after SO seconds and lock,
If the Keylock feature is used in coniunction with the Closed drawer option, pressing the
@ button will not unlock the drawer, The Keylock feature must be turned off to enable
DishDraweP _to be opened,
Note: this option is highly recommended if the DishDrawer is to be used in motor homes.
Clean dish indicator option (modeb with LCD only)
By default, DishDraweP _is programmed with the Clean dish indicator option off, When the Clean
dish indicator option is on, the uunnsymbol will remain in the electronic display after a wash
program has finished to indicate the dishes are dean, When you have unloaded all the dishes,
press the @ button to return to normal operating mode,
This option might be useful when dishes have been left in DishDrawe¢ _and you cannot
remember if they have been washed or in situations where household members regularly
remove only a few clean dishes without emptying the drawer,
We do not recommend the Clean dish indicator option be used in conjunction with the Closed
drawer option.

Option adjustments
S
©
©
©
a
u
©
o
E
o
2
©
8
liiii_
Jiiii_
'i@
©

!ii
Option adjustn'sents
l:Iilt
i i
E
_4
U
i J
O
i J
i;8i i
_o
E
i i
O o
i u_j
0
i!_.i
0
oo
o
i i
O o
i j
$
0
@
@
2
.2
0
Z

User maintenance
Cleaning the surfaces
We do not recommend the use of the following cleaning aids on your D_shDrawer ®as they may damage
the surfaces:
Plastic or stainless steel scouring pads
Abrasiv6 solvent, househoM cleaners
Acid or atkaline cteaners
Hand washing #quids or soap
Laundry detergents or disinfectants
Propfletary "Stainless 5teeF cleaners or polishes as these may damage the protective coating.
1 Wipe with a clean damp cloth, Take care not to wet the control panel.
2 Dry with a clean lint-free cloth.

User n'saintenance instructions
Cleaning the drain filter, sisray arm and
filter Is[ate
We recommend that the drain filter is cleaned
whenever there is evidence of food particles,
The spray arm and filter plate may need cleaning
about once a month in normal use or more often
should the need arise.
If a dishwasher cleaner/descaler is used, you must
run a wash program with detergent immediately
afterward to prevent any damage to your
DishDrawer ®.
Internal parts of the DishDrawer ° :
a Spray arm
The D_shDrawer must be used with the fi_terpiat6
dra_n fi_terand 5pray arm correcdy in piaceo
Cleaning the drain filter
'I Lift up the drain filter access panel on the base rack (if fitted),
2 Lift and removethe drain filter,
s Empty, rinse dean under running water and replace back into the allocated space.
a Ensure the drain filter is flush with the filter plate.
®
b Filter plate
c Drain filter

User _aintenanc@
CJeaning the spray arm and fiJter p_ate
Ensure the DishDraweP is cool before you start cleaning and follow the instructions for
removing the drain filter and spray arm.
I{_ Unclip the glass supports from the rack wires and
fold all the adjustable racks away, so that they are
upright and dose to the top,
2 Remove the base rack carefully. Lift from the
back end first to prevent knocking the
detergent and rinse agent dispenser,
s Lift the spray arm and shake any foreign material
out
Rinse the spray arm clean under running water
and wipe the with a damp cloth,
4 In the center of the filter plate there are two rings.
Hold the center ring still and turn the outer ring
counter-clockwise, about a 1/8 turn, This will
release the filter phte,
5 Lift thefilter plate out
When cleaning the underside of the filter [:)late,
take care handling the sharp outer edge to avoid
the risk of cuts,
Remove any foreign material, wash in hot soapy
water and rinse thoroughly in dean water. The
heater plate can be wiped with a damp clotL
6 Replace the filter plate so it lies flat in the base of
the drawer ensuring the filter plate is fully locked
into position with the center ring.
_9tock the fi#er ptate ff}to _ition, ensure the lines atign
with each other (c)and a_lthree pin pairs fiffnty ff_teflock (e)o
Referto the diagram forthe correct posLffono
Thetiger pJate must not be able to move about ffedyo
7
Replace the spray arm back onto the impeller,
8
Replace the base rack, lowering its front edge into
position first.
Note: Where there is broken crockery or glass in the
drawer, it must be carefully removed to prevent
damage to the DishDrawer%
Correct locking position of filter
plate with motor assembly
(under spray arm)
a Outer ring
b Impeller
c Correct alignment marks
d Center ring
e Interlocking pins

Unclean dishes
Wash program unsuitable Refer to the'Wash program chart'for a
for the load. suitable wash program, or the soils were
too heavily baked on and dishes may need
soaking.
Spray arm unable to rotate. Ensure no items are obstructing the spray
a!m pat(_
DishDrawer _'_overloaded/ Refer to the section on loading.
Filter plate/drain filter is Refer to the 'User maintenance instructions'
.... qsst!oe.
Detergent put in the wrong Detergent must be placed in the large
compartment, compartment.
Excess food not removed Scrape all food scraps off dinnerware prior to
from dinnerware prior to loading.
loading.
Unsuitable detergent. Use recommended brands of dishwasher
..........................................................................................................................................detfirger}t:......................................................................................................................................................
Not enough detergent. Refer to the detergent section or the
detergent manufacturer's instructions.
Spray arm holes are blocked. Clean the spray arm.
Filter plate/drain filter is Clean the filter plate and drain filter.
blocked.
Insufficient salt in the Ensure there is enough salt in the water
water softener (DD24-oH softener and/or increase the water
models only)_ softener setting_
Foaming Incorrect amount of Refer to the detergent section or consult the
detergent, detergent manufacturer's instructions.
Too much egg in the wash Increase the amount of detergent,
load,
Rinse agent setting too higL Decrease the rinse agent setting,
Water leaking
DishDrawer _wi[[
not open
Power failure
during cycle,
Drain hose disconnected Reconnect the drain hose to the waste pipe,
....fr°!Y},,V_aS!e£!£e:............................................................................................................................................................................................................................................................................................
Water inlet hose not Ensure the inlet hose is connected securdy,
.....erf_Per!_i.COr}nec!ed:
Other leaks. Turn water and power supplies to the
DishDrawe¢ _off. Call your dealer or
Authorized Service Agent.
Childlock feature is on or Turn the Childlock off. Hold down the _/@
the Closed drawer option is button until the@ symbol disappears from
on, or both. the LCD screen or the light above thee/@
button disappears and/or press the O
button to open the DishDrawer_L
Wait until power resumes, cycle will restart in
same part of wash program.

Continuous Afaulthasoccurred. Refertothe'Faultcodes'section.
beeping
Intermittent DishDrawe¢_isinpause ClosetheDishDrawe¢_andpresstheHt
beeping mode. button.
DishDrawe¢_will
not start
Powersupplyisnot Connectthepowersupply.
connected.
Thedrawerisnotclosed Ensurethedrawerisfirmlyclosed.
is on. down the _/@ button until the@ symbol
blt button not pressed, Press the HI button,
Excess water in the Drain hose(s) bent or Straighten the drain hose{s).
DisbDrawer _ kinked.
Blocked filters, Clean the filter plate/drain filter. Refer to the
Water marks on the Rinse agent depReted. RefiR[the rinse agent dispenser.
dishes Rinse agent setting too low. Increase the rinse agent setting.
DishDraweP _overloaded/ Refer to the section on loading.
incorrectly loaded.
Insufficient or no salt in the Ensure there is enough salt in the water
water softener (DD24-oH softener and/or increase the water
models only), softener setting.
DishDrawe¢ _ Some foods, like tomato Pre-dnse dishes before placing in the
interior is stained based products, may DishDrawePL Alternatively, using the Rinse
stain the inside of the program after adding the dishes may
DishDrawePL minimize staining.
Dishes did not dry Incorrect loading. Ensure the dishes are not nesting together.
Rinse agent depleted. Refill the rinse agent dispenser.
Rinse agent setting too low. Increase the rinse agent setting.
Eco wash program used_ Choose a standard wash program_
No detergent Detergent dispenser was Clean the dispenser and ensure the
dispensed wet when Ioaded_ dispenser is dry when adding detergent_
Excessive motor The filter plate and/or spray Refer to the'User maintenance instructions'
noise arm is incorrectly placed, section for details on correct placement.
No water in the motor area. This usually occurs on the first use or when
disappears from the LCD screen or the light
above thee/@ button disappears,
'User maintenance instructions' section,
the DishDraweP _ has not been used for
long periods of time, Run the DishDraweP _
through a wash program,

Fau t codes
How to recognize a fault code
When afault hasoccurred, the DishDraweg will continuously beep every second.
The fault code will be displayed on the electronic display for models with LCDand on the wash
program selector for models with no LCD.
Eachfault code isshown in the following chart,
How to attend to a fault code
1 Press the O button to remove the fault code,
2 If the fault code and continuous beeps cannot be removed by pressing the O button, turn the
DishDrawe¢ '_off at the power supply,
3 We recommend you check the following chart and correct the fault where possible,
4 After attending to the fault, turn the DishDrawe¢ '_on at the power supply,
5 If the fault code and continuous beeps remain, turn the water and power supply off to the
DishDrawe¢<
6 When calling your Authorized Service Center, advise them of the fault code that has appeared
on the DishDrawegE This information will help the Authorized Service Center respond to your
request,

Fau t codes
[ r ,
Flood switch has been
activated,
Turn the water and power supply to the
DishDraweP off and call your Authorized
Service Center.
HFAVY NORMAL FAST DEUCATS RtNS_
F2 _ _,,, Motor problem. Call your Authorized Service Center.
t J
HSAVY NOR_'V,_L FAST DSUCA_E RINSE
F3 Temperature sensor Ensure water coming in through the inlet
, _ failed, hose is less than 150 °R You may need to
install a tempering valve on your water
H_:AVY NORNfAL FAST DELICATE RDJSE
F4 Faulty temperature Call your Authorized Service Center.
. , sensor or element
HT_Z_VY NORMAL b2_ST DELICATE R_dS_;"
F5 [ FE < Lid fault 1 Turn power supply to DishDrawer off,
[ "J J then turn on power supply_ Fault may
reset.
u_vYN_,_,_A_FAST_L£4"rE_'SE 2 Ca[[ your Authorized Service Center.
F6 Lid fault 1 Turn power supply to DishDrawer off,
, then turn on power supply_ Fault may
reset.
HFAVY NOR&#AI,, FAST DSUCATS RINSE _ Ca[[ your Authorized Service Center.
F7 F] _ Lid fault Call your Authorized Service Center.
F8 Electrical problem 1Turn power supply to DishDrawer off.
. , 2 Call your Authorized Service Center.
HWAVY NOR_IAL FAST DE:TJCATE RINS_
F9 Electronics
Call your Authorized Service Center.
. , malfunction.
HEAVY NORMAL FAST DELICATE RINS_

Fau_tcodes
il!!:!
U1 ®
HEAVY NOR&'_AL F_SY DEMCAT_ R_NSE
U4 _L_
uq
Fill Fault
Fault in the other
drawer preventing the
use of this drawer
1 Turn the DishDrawe¢ _water supply on,
2 Ensure the spray arm is placed on the
impeller and can rotate and if the
DishDrawe¢ '_is fuji of water, it will
need to be emptied manually,
3 Call your Authorized Service Center,
Check other drawer, attend to fault code
on that drawer.

Warranty and service
Before you ca[[ for service or assistance ooo
Check the things you can do .vourseff, Referto the installation instructions and your userguide
and check that:
"_ your product is correctly installed
2 you are familiar with its normal operation,
If after checking these points you still need assistance, please refer to the Service & Warranty
book for warranty details and your nearest Authorized Service Center, or contact us through our
website listed on the back cover,