Fisher Paykel DD24DVT7 Installation

INSTALLATION INSTRUCTIONS

DishDrawer

DD24DUT7 and DD24DVT7

TM

dishwasher

models

US CA

590225B 04.14

1

SAFETY AND WARNINGS

3

WARNING!

Electrical hazard

Before installing the dishwasher, remove the house fuse or open the circuit

breaker. If permanently connecting the dishwasher, be sure the power is isolated
and the dishwasher unplugged.

GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having
an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
with all local codes and ordinances. WARNING - Improper connection of the
equipment-grounding conductor can result in a risk of electric shock. Check with
a qualified electrician or service representative if you are in doubt as to whether
the appliance is properly grounded.

If the dishwasher is installed as a permanently connected appliance:
GROUNDING INSTRUCTIONS - This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment-grounding
terminal or lead on the appliance.
Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Cut hazard

Take care - panel edges are sharp.

IMPORTANT SAFETY INSTRUCTIONS!

Installation of this dishwasher requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building, electricity, and plumbing regulations.
At the completion of the dishwasher installation, the Installer must perform the Final Checklist.
Remove all packaging materials supplied with the dishwasher.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

The switched power outlet must be outside the dishwasher cavity, so that it is accessible after

installation.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord and hoses.
If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.

Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should

not be reused.
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,

boat or mobile facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.

The DCS by Fisher & Paykel DishDrawer dishwasher is designed for connection to the national power

supply grid. In some instances connection to off-grid alternative energy systems, such as wind, solar
and stand alone generation, may result in damage to the electronic control of the appliance. Any
damage to the control as a direct consequence of connection to alternative energy sources will not be
covered under the terms of the Warranty.

SAVE THESE INSTRUCTIONS

Failure to use caution could result in injury or cuts.

2

PARTS SUPPLIED

4

Drain hose
support (1)

Moisture protection
tape (1)

(to prevent moisture
damage)

Drain hose
joiner (1)

Hexagonal
socket for feet
adjustment (2)

(long & short)

Wire clip (2)
(for securing

Drain hose joiner)

Prefinished toekick (1)

Clamp (1)
(for securing

Drain hose joiner)

Side mounting
bracket kit
(A and B) (2)

OPTIONAL

Edge Protector (1)

(If the services hole is through
a metal partition the hole
must be protected with the
Edge protector supplied to
prevent damage to the power
cord or hoses.)

Top
mounting
brackets (2)

OPTIONAL

Phillips
⁄” (16 mm)
screws (9)

If the Drain hoses supplied are not long enough
to reach your services, you must use a Drain Hose
Extension Kit P/N 525798 which will extend the drain
hoses by 11’ 10” (3.6m).
The kit is available from the nearest DCS by Fisher
& Paykel Authorized Service Center, or Toll free

1.888.936.7872 or www.dcsappliances.com

Rubber
washer for
inlet hose (1)

(comes already
fitted)

9

12

11

11

10

4

5

6

7

7

8

8

3

100 mm

2

4

5

1

OPTIONALLY HARD WIRING PRIOR TO INSTALLATION

5

3a

REMOVE THE LOWER DRAWER

4” (100mm)

3c

TERMINATE THE WIRING AS SHOWN

Press the release tabs in on
either side and push back
to release drawer from
runners.

Remove knock-out for cable clamp and
fit a suitable cable clamp for the conduit.

3

Access
cover

To prevent kinked hoses, we recommend
rotating the drawer anti-clockwise and
resting it on its side after removal.

3b

REMOVE THE ACCESS COVER & POWER CORD

Electrical Shock Hazard

Before continuing, ensure that the product is
disconnected from the power supply.

Failure to follow this warning may result in
electrical shock, injury or re.

3d

REFIT THE DRAWER ONTO THE RUNNERS & CLOSE

Pull forward the release tabs
on both sides 4”(100

WARNING!

mm)

Ensure the drawer
is now rotated
clockwise back.

16

15

19

Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.

13

Ensure the release tabs on
both sides are reset fully.

14

Use copper conductors only.

4

PRODUCT DIMENSIONS

6

O

I

K

Plan

C

D

NA

O

L

Side

F

G

B

M

H

Product dimensions inches (mm)

overall height1 of product 34 - 36 ⁄”(864-924)

A

overall width of product 23 ⁄”(605) 23 ⁄”(605)

B

overall depth of product (excl. handle) 22 ⁄”(577) 22 ⁄”(577)

C

depth of chassis (to back of front panel) 21 ¾ ”(553) 21 ¾ ”(553)

D

maximum extension of drawer (excl. handle) 21 ¾ ”(552) 21 ¾ ”(552)

E

depth of front panel (excl. handle) 1”(25) 1”(25)

F

height1 of chassis 33 ⁄”(855) 33 ⁄”(855)

G

height of levelling feet ⁄ - 2 ⁄”(9-69)

H

depth of handle 2 ⁄”(66) 2 ⁄”(60)

I

depth of toekick recess (to back of front panel)

J

height of upper front panel 17 ⁄”(442) 17 ⁄”(442)

K

ventilation gap between front panels ⁄”(8) ⁄”(8)

L

height of toekick panel (adjustable) 2 ¾ - 4 ¾ ”(70-120)2 ¾ - 4 ¾ ”(70-120)

M

height of drawer fronts 29 ⁄”(760) 29 ⁄”(760)

N

height from top of handle to top of front panel 2 ⁄”(62) 2 ⁄”(62)

O

1

includes ⁄” (2mm) high bracket slots 2depending on adjustment of leveling feet 3adjustable to match toekick recess on adjoining cabinetry

3

J

DD24DUT7

2

2

1 ⁄ - 3 ⁄”(30-92) 1 ⁄ - 3 ⁄”(30-92)

34 - 36 ⁄”(864-924)

⁄ - 2 ⁄”(9-69)

E

DD24DVT7

2

2