Fisher WH8560F, WH8560P, WH8060F, WH8060P, WH7560P Installation Instructions Manual
...
Installation instructions
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/QuickSmart/WH7560J3/User_Guide_WH7560J3/03_Installation_instructions
Updated: Sat, 13 Jan 2018 05:02:40 GMT
Powered by
Accessories
Please check you received the following accessories with your Fisher & Paykel washer. You will find them inside
the drum or attached to the packaging.
• 2 x Inlet hose(s) (for models WH8560J and WH7560J only 1 x Inlet hose supplied)
• 1 x Drain hose guide
• 1 x Installation instructions and user guide
• 1 x Spanner
• 1 x Installation leaflet (attached to the top of the washer)
• 1 x Inlet valve cap (excluding WH8560J and WH7560J models)
Unpacking
To ensure the best performance from your new washer please follow the instructions below.
Removing the packaging
1. Remove the outer packaging (including the polystyrene packer and plastic wrapping). All packaging must be
removed prior to use. Ensure these materials are kept out of reach of children.
1
A small amount of water may be seen inside the packaging and inside the washer. This is
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/QuickSmart/WH7560J3/User_Guide_WH7560J3/03_Installation_instructions
Updated: Sat, 13 Jan 2018 05:02:40 GMT
Powered by
the result of factory testing and is normal.
2. Tilt the machine backwards and ‘walk’ it off the base one foot at a time. Not doing so may cause damage to
your floor and washer.
3. Remove all packaging and accessories from inside the drum.
Removing the transit bolts
The clothes washer is fitted with 4 transit bolts at the rear to avoid damage during transportation.
The 4 transit bolts MUST be removed prior to operation of the machine. Failure to remove
these will result in damage to the machine.
To remove the bolts:
1. Use a spanner or socket to unscrew and remove all four transit bolts at the back of the washer (A).
2. Pull the black rubber grommets to remove the bolt, grommet and white plastic spacers from the machine. Keep
the transit bolts in case they are required for future transit of the machine. Never transport the machine
without the transit bolts properly fixed in place.
3. Cover the bolt holes with the white plastic plugs which are attached to the machine and located near each hole
(B). Push to clip into place.
Removing the transit safety bolts
2
Product dimensions
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/QuickSmart/WH7560J3/User_Guide_WH7560J3/03_Installation_instructions
Updated: Sat, 13 Jan 2018 05:02:40 GMT
Powered by
Property (mm)
A. Overall height of product.
B. Overall width of product.
C. Overall depth of product (including dial and door
when closed).
D. Depth of door open.
E. Minimum door clearance to adjacent wall.
Standpipe height.
Maximum Capacity
WH8560F/
WH8560P/
WH8560J
850 850 850
600 600 600
645 645 590
1065 1065 1010
330 330 330
min. 800 –
1200
WH8060F/
WH8060P
min. 800 –
1200
WH7560P/
min. 800 –
WH7560J
1200
WH8560F/
Property (kg)
A. Overall height of product.
WH8560P/
WH8560J
8.5 8.0 7.5
WH8060F/
WH8060P
WH7560P/
WH7560J
3
Loading...