Size:
881.24 Kb
Download

INSTRUCTION MANUAL

Color Video Monitor

VMC-8618VMC-8613

About this manual

Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.

This manual gives basic connections and operating instructions for 2 models.

SANYO INDUSTRIAL VIDEO

VIDEO MONITOR LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-freenumber listed below.

For product operation, authorized service center referral, service assistance or problem resolution, call

CUSTOMER INFORMATION 1-800-421-5013

Weekdays 8:30 AM – 5:00 PM Pacific Time

For accessories and/or parts, call

PARTS ORDER INFORMATION 1-800-726-9662

Weekdays 8:30 AM – 5:00 PM Pacific Time

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER.THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.

 

 

 

LABOR

PARTS

PICTURE TUBE

 

 

 

1 YEARS

1 YEARS

1 YEARS

 

 

 

 

 

 

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operatedcontrols as explained in the appropriate model’s instruction manual, or

(B) the repair of any product whose serial number has been altered, defaced or removed.

This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.

This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.

The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.

SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR’S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

ATTENTION

For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.

Model No. _____________________________________________

Serial No.______________________________________________

 

(Located on back or bottom side of unit.)

Date of Purchase _______________________________________

Purchase Price _________________________________________

Where Purchased _______________________________________

 

21605 Plummer Street,

 

Chatsworth, California 91311

1AC6P1P2388--

 

L8MV5/US, L8MW5/US (1000KP-TVS)

Printed in Taiwan

INFORMATION TO USER

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLEPARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Explanation of graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC COMPLIANCE STATEMENT

FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSINGEQUIPMENT REGULATIONS.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A RESPECTE TOUTES LES EXIGENCES DU RÈGLEMENT CANADIEN SUR LE MATÉRIEL CAUSANT DES INTERFÉRENCES.

1

IMPORTANT SAFEGUARDS

1.READ INSTRUCTIONS --All the safety and operating instructions should be read before the appliance is operated.

2.RETAIN INSTRUCTIONS --The safety and operating instructions should be retained for future reference.

3.CLEANING --Unplug video monitor or equipment from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4.ATTACHMENT --Do not use attachments not recommended by the video monitor or equipment manufacturer as they may result in the risk of fire, electric shock or injury to persons.

5.WATER AND MOISTURE --Do not use the video monitor or equipment near water--for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, or the like.

6.ACCESSORIES --Do not place video monitor or equipment on an unstable cart, stand or table. The video monitor or equipment may fall, causing serious injury to a child or adult, and serious damage to the equipment. Wall or shelf mounting should follow the manufacturer’s instructions, and should use a mounting kit approved by the manufacturer.

6A. Video monitor or equipment and cart combinations should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn.

7.VENTILATION --Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to ensure reliable operation of the video monitor or equipment and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the video monitor or equipment on a bed, sofa, rug, or other similar surface. Video monitor or equipment should never be placed near or over a radiator or heat register. Video monitor or equipment receiver should not be placed in abuilt-ininstallation such as a bookcase unless proper ventilation is provided.

8.POWER SOURCES --Video monitor or equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your video monitor or equipment dealer or local power company. For video monitor or equipment designed to operate from battery power refer to the operating instructions.

9.GROUNDING OR POLARIZATION --This product is equipped with athree-wiregrounding-typeplug, a plug having a third (grounding) pin. This plug will only fit into agrounding-typepower outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of thegrounding-typeplug.

10.POWER CORDS --Do not allow anything to rest on the power cord. Do not locate video monitor or equipment where the cord will be abused by persons walking on it.

11.HEED WARNINGS --Follow all instructions marked on the video monitor or equipment.

12.LIGHTNING --For added protection for video monitor or equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning andpower-linesurges.

13.OVERLOADING --Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

14.OBJECT AND LIQUID ENTRY --Never push objects of any kind into video monitor or equipment through openings as they may touch dangerous voltage points orshort-outparts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

15.SERVICING --Do not attempt to service video monitor or equipment yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

16.DAMAGE REQUIRING SERVICE --Unplug video monitor or equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions.

A.When the power-supplycord or the plug has been damaged.

B.If liquid has spilled, or objects have fallen into the video product.

C.If the video product has been exposed to rain or water.

D.If the video product does not operate normally by following the operating instructions, adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.

E.If the video product has been dropped, or the cabinet damaged.

F.When the video product exhibits a distinct change in performance --this indicates a need for service.

17.REPLACEMENT PARTS --When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards.

18.SAFETY CHECK --Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.

2

PRECAUTION CONTENTS

If an abnormality does occur, turn the power switch off and unplug the unit. Have a qualified technician perform any repairs.

Do not use the monitor if it makes a strange noise, emits a strange odor, or if smoke comes out from it

If used under these conditions, the monitor may cause a fire or electric shock. Immediately unplug it and wait to make sure no more smoke comes from it. Then take it to the dealer for service. Do not try to repair or open the monitor yourself.

Do not allow the power cord to get damaged

Do not place heavy objects on the power cord.

Do not place the power cord near a heat source.

Do not excessively bend the power cord, modify it, or secure it with staples.

Doing so may damage the power cord and cause a fire or electric shock.

If the power cord is damaged, take it to the dealer and have it replaced.

Do not allow dust or dirt to build up on the power cord or power outlet

A build-upof dust may cause a short circuit or generate heat and cause a fire.

Be especially careful when using the monitor in areas of high humidity, in areas with frequent condensation, in kitchens, and in places where there is excessive dust.

Periodically unplug the power cord and clean away the dust that builds up between the plug terminals.

Cautions when plugging in the power cord

Make sure you insert the plug of the power cord all the way in the power outlet. Using the monitor with the power cord not fully plugged in may cause heat to generate and cause a fire.

Do not use the monitor with the power cord wound or tied up. Heat may generate and cause a fire.

When using an extension cord, be sure that the total current load of all equipment connected to it dose not exceed the specified ratings of the extension cord. If the rating are exceeded, heat may generate and cause a fire. Make sure to carefully read the specifications accompanying the extension cord.

Cleaning

Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth.

Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling.

SERVICE

This unit is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . 4 CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . 6 BASIC OPERATION . . . . . . . . . . . . . . . . . . . 7 ADJUST THE OSD MENU ITEM . . . . . . . . . . 8 LANGUAGE SCREEN TABLE . . . . . . . . . . . 11 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 13 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . 14

FEATURES

Equipped with video and audio input terminals

The video and audio input terminals (two systems for each input) allow bridge connections.

Equipped with Y/C input (S-VIDEOinput) terminal

This terminal is used to input Y/C separation signals (S-VIDEOsignals).

3

PARTS NAMES

Front Panel

1Speaker

When the monitor selector button (A, B or Y/C) is pressed, the speaker lets you hear the sound from the components which are connected to the terminals at the rear of the monitor. (Use components which produce audio output.)

2On-screendisplay button (OSD)

When this button is pressed, the menu screen appears on the monitor screen.

PARTS NAMES

Rear Panel

2 3 4

1

1AC INPUT socket

Connect the AC power cord (supplied) securely to this socket and to a wall outlet.

2Rear A terminals (AUDIO/VIDEO A terminals)

When the monitor A selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored.

A AUDIO OUT/IN terminals B VIDEO OUT/IN terminals

3Rear B terminals (AUDIO/VIDEO B terminals)

When the monitor B selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored.

C AUDIO OUT/IN terminals D VIDEO OUT/IN terminals

4Rear Y/C terminals (AUDIO/VIDEO Y/C terminals)

When the monitor Y/C selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored.

E AUDIO OUT/IN terminals F S-VIDEOOUT/IN terminals

Note: If there is no signal being input from the input terminals selected (A, B or Y/C) at the rear of the monitor, “NO SIGNAL” will be displayed.

5

CONNECTION

Before making any connection, make sure all the devices are turned off.

Before making the connections, please refer to the instruction manual accompanying each device. If the devices are not connected properly, that may cause a fire and/or damages.

Basic connections

Connections to the S-VIDEOterminals

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Monitor

 

Video recorder

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To Video

To AUDIO

 

 

 

: IN signal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

: OUT signal

 

 

 

 

 

 

 

input terminal

input terminal

 

 

 

 

 

 

To Audio input

 

 

 

 

 

 

 

 

To S-VIDEOinput terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To Video input terminal

To Audio input terminal

To AUDIO A

 

INPUT terminal

(Rear panel)

 

To VIDEO A

 

INPUT terminal

To AUDIO

To AUDIO B

input terminal

INPUT terminal

 

To VIDEO B

To Y/C input terminal

 

INPUT terminal

 

Video camera

Monitor

Video recorder

Video camera

Monitor

Video recorder

Note:

The components and connection cables are not included and must be purchased separately.

If connecting a single component, it can be connected to either the A or B terminals at the rear of the monitor.

6

BASIC OPERATION

1 Press the POWER button to turn on the power.

ON: The power is turned on (the POWER indicator is lit). The signals from the channel (A, B or Y/C) which was being used when the power was last turned off will be input.

OFF: The power is turned off (the POWER indicator is off).

Note: If the power for the connected components is not turned on, or if a problem with operation has occurred, “VIDEO LOSS” will appear on the screen. If this happens, check the component concerned.

2 Select the audio and video input.

Use the monitor selector buttons (A or B) at the front of the monitor to select the picture being input to either the A or B terminals at the rear of the monitor.

If using the S-VIDEOinput terminal at the rear of the monitor, press the monitor Y/C selector button.

Note: If there is no signal being input from the input terminals selected (A, B or Y/C) at the rear of the monitor, “NO SIGNAL” will be displayed.

3 Menu screen operations

1Press the OSD button.

The menu screen will be displayed.

The menu screen will only be displayed for about 13 seconds.

2Press the cursor (l) or (j) button.

The cursor will move up or down, so that you can select the desired menu item.

To return to the normal monitor screen

Press the OSD button once more, or

Select “EXIT: OSD” and then press theENTER button.

3Select the desired menu item and then press the ENTER button.

If you press the ENTER button repeatedly while the menu screen is being displayed, the display will alternately change between the menu screen and the setting screen. At this time, the menu item will still be selected.

Note: During this operation, “9. TITLE” and “10. VERSION” will be skipped and the screen will go straight to “EXT: OSD”.

ADJUST THE OSD MENU ITEM

Open the menu screen (press the OSD button), use the cursor buttons to select the desired menu item, and then press theENTER button.

BRIGHTNESS adjustment

1Select “3. BRIGHTNESS 75%” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the brightness of the picture.

Note: The setting characters which are displayed on each adjustment screen (such as 50%) may not display correctly (dropout) in some cases.

COLOR adjustment

1Select “1. COLOR 50%” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the color of the picture.

TINT adjustment

1Select “2. TINT 53%” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the tint of the picture (NTSC only).

CONTRAST adjustment

1Select “4. CONTRAST 75%” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the contrast of the picture.

SHARPNESS adjustment

1Select “5. SHARPNESS 75%” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the sharpness of the picture.

ADJUST THE OSD MENU ITEM

VOLUME adjustment

1Select “6. VOLUME 50%” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the sound volume.

OSD

Monitor switching time (dwell time) setting

For Model 8613 only

1Select “7. DWELL TIME 5S” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to adjust the dwell time.

The time can be set to between 1 second and 31 seconds.

Menu screen language setting

1Select “8. LANGUAGE” and then press the ENTER button.

2Use the cursor (l) and (j) buttons to select the display language.

Only the menu screen and setting screen languages will be changed. (See page 11.)

OSD

OSD

3Return to the menu screen display and then press the SEQUENCE button.

SEQ” will be displayed on the screen.

Note: If SEQ is not displayed, no dwell time has been set.

9

ADJUST THE OSD MENU ITEM

Displaying characters such as for setting location on the monitor screen (Refer to “CHARACTERS TABLE”.)

Note: If there is no signal being input from the input terminals selected (A, B or Y/C) at the rear of the monitor, the title cannot be set for those terminals.

1Select “9. TITLE ON” and then press the ENTER button.

2To display “ABCD” on the CH B monitor as an example:

A maximum of eight characters can be displayed on the screen.

Note: The setting screen will disappear after approximately 13 seconds of no activity.

1. Use the cursor (l) button to select “CH B”.

2.Press the ENTER button, and then use the cursor l (j) button to select “A”.

3.Press the ENTER button, and then use the cursor l (j) button to select “B”.

4.Press the ENTER button, and then use the cursor l (j) button to select “C”.

5.Press the ENTER button, and then use the cursor l (j) button to select “D”.

6.Press the OSD button.

The cursor will move to the next monitor display. The settings for the CH A andCH Y/C monitors can be carried out by the same procedure as described above.

3Use the cursor l (j) button to select “TITLE

ON”, and then press the ENTER button.

The text that has been set for that monitor screen

will then be displayed.3 14 2l52.113 822 23226 c Rc98744

LANGUAGE SCREEN TABLE

English

Français

Deutsch

Menu

Title/channel

Automatic title/ channel selection

Title settings

COLOR adjustment

TINT adjustment

BRIGHTNESS adjustment

CONTRAST adjustment

SHARPNESS adjustment

VOLUME adjustment

DWELL TIME setting

LANGUAGE SCREEN TABLE

Español

Italiano

Russian

Menu

Title/channel

Automatic title/ channel selection

Title settings

COLOR adjustment

TINT adjustment

BRIGHTNESS adjustment

CONTRAST adjustment

SHARPNESS adjustment

VOLUME adjustment

DWELL TIME setting

TROUBLESHOOTING

Solutions to common problems related to your monitor are describe here. If none of the solutions presented here solve the problem, unplug the monitor and consult a SANYO-authorizeddealer or service center for assistance.

Problems

Points to be checked

Measures (Remedy)

Page

 

 

 

 

No picture with

Is the video signal being output from the

Set the connected component correctly.

6

the power on

connected component?

 

 

 

 

 

 

 

 

Is the input signal selected properly?

Select the required video signal input

4

 

 

with the monitor selector buttons. (A, B

 

 

and Y/C)

 

 

 

 

 

No sound.

Is the audio signal being output from the

Set the connected component correctly.

6

 

connected component?

 

 

 

 

 

 

 

 

 

Is the volume set to the minimum level?

Adjust the volume using the VOLUME

9

 

 

setting screen.

 

 

 

 

 

 

 

 

Is the audio cable disconnected?

Securely connect the audio cable.

6

 

 

 

 

Shaking picture

Is the monitor close to a device which is

Move the device away from the monitor

 

generating a strong magnetic field?

until the picture stabilizes.

 

 

 

 

 

 

No color, color is

Have the picture control settings

Adjust the settings using the adjustment

 

incorrect or

(CONTRAST, BRIGHTNESS, TINT)

screens.

8

picture is too

been changed?

 

 

 

dark

 

 

 

 

 

 

 

Uneven or

Are there any speakers or magnets

Move the speaker or magnet away from

 

mismatched

nearby, or were they brought close to the

the monitor, and then turn the power off

color in parts of

monitor?

and wait at least 30 minutes before

 

the picture

 

turning the power back on again.

 

 

 

 

 

13

SPECIFICATIONS

 

VMC-8613

 

VMC-8618

Color system

PAL/NTSC, selected automatically

Picture tube

 

 

13 inch

 

18 inch

Resolution

More than 750 TV lines

 

More than 800 TV lines

Input terminals

 

 

 

S-VIDEOsignal (VIDEO C)

Separate Y/C signal, mini-DINconnector (1)

 

Y signal: 1.0 Vp-p,75 Ω negative sync

 

C signal: 0.286 Vp-p,75 Ω negative sync, bridge connection possible

Video signal (VIDEO A, B)

Composite sync signal, 1.0 Vp-p,75 Ω BNC connector (2)

Audio signal (AUDIO A, B)

–6dBs (400 Vrms), RCA pin (3), bridge connection possible

Output terminals

 

 

 

S-VIDEOsignal (VIDEO C)

Separate Y/C signal, mini-DINconnector (1)

 

Y signal: 1.0 Vp-p,75 Ω negative sync

 

C signal: 0.286 Vp-p,75 Ω negative sync, bridge connection possible

Video signal (VIDEO A, B)

Composite sync signal, 1.0 Vp-p,75 Ω BNC connector (2), automatic termination setting

Audio signal (AUDIO A, B)

–6dBs (400 Vrms), RCA pin (3), bridge connection possible

Menu screen items

 

 

 

Picture adjustment

Adjustable COLOR, TINT (NTSC only), BRIGHTNESS, CONTRAST, SHARPNESS

Sound adjustment

Adjustable speaker volume

Automatic screen switching time

 

 

1 second to 31 seconds (1-secondunits)

 

Language setting

Six languages English, Francais, Deutsch, Espanol, Italiano and Russian)

Title setting

Title entry up to [eight] alphanumeric characters

Overscan or underscan selection

 

 

 

YES

Speaker

Variable round x1

 

Audio output

1 W

 

Power source

100 ~ 240 V AC, 50/60 Hz

Power consumption

 

 

82 W

 

95 W

Ambient operating temperature

–10~ 45˚C, storage temperature

Ambient operating humidity

10 ~ 90%

 

Dimensions (W x H x D)

 

 

350 x 350 x 378 mm

 

448 x 433 x 447 mm

Weight

14 kg

 

25 kg

Accessory

AC power cord x1

 

 

 

 

 

Diagrams are shown for explanatory purposes only, and have been exaggerated, abbreviated or created as required, and so may differ from the actual product.

Features and specifications are subject to change without prior notice or obligations.

Dimensions

W

D

Y/C (Mini DIN 4 pin) terminal specification

 

 

 

OUT

3

Pin No.

Signal

 

 

4

 

 

 

 

2

1

1

GND (Y)

 

 

 

 

 

H

4

3

2

GND (C)

 

 

 

3

Y

 

 

2

1

 

 

IN

 

4

C

 

 

 

 

14