Page 1
Instruction Manual
D100397X012
Fisher™ ES and EAS easy‐e™ Valves
CL125 through CL600
ES Valve
July 2017
Contents
Introduction 1.................................
Scope of Manual 1.............................
Description 2.................................
Specifications 2...............................
Installation 2..................................
Maintenance 4.................................
Packing Lubrication 5..........................
Packing Maintenance 6.........................
Replacing Packing 6........................
Trim Maintenance 11..........................
Disassembly 11............................
Lapping Metal Seats 13.....................
Valve Plug Maintenance 13..................
Assembly 13..............................
ENVIRO‐SEAL
Replacing a Plain or Extension Bonnet with an
Replacement of an Installed ENVIRO‐SEAL
Purging the ENVIRO‐SEAL Bellows
Parts Ordering 17...............................
Parts Kits 17...................................
Parts List 19...................................
™
Bellows Seal and Bonnet 14........
ENVIRO‐SEAL Bellows Seal (Stem/Bellows
Assembly) and Bonnet 14.................
Bellows Seal (Stem/Bellows Assembly) 16...
Seal Bonnet 17..........................
Figure 1. Fisher ES Valve with 657 Actuator
W2174‐3
Introduction
Scope of Manual
This instruction manual includes installation, maintenance, and parts information for NPS 1/2 through 8 Fisher ES
valves, and NPS 1 through 6 EAS valves, through CL600 ratings. Refer to separate manuals for instructions covering the
actuator and accessories.
Do not install, operate, or maintain an ES valve without being fully trained and qualified in valve, actuator, and
accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important to
carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If you
have any questions about these instructions, contact your Emerson sales office
proceeding.
www.Fisher.com
or Local Business Partner before
Page 2
ES Valve
July 2017
Table 1. Specifications
Instruction Manual
D100397X012
End Connection Styles
Cast Iron Valves
Flanged: CL125 flat‐face or CL250 raised‐face flanges
per ASME B16.1
Steel and Stainless Steel Valves
Flanged: CL150, 300, and 600 raised‐face or ring‐type
joint flanges per ASME B16.5
Shutoff Classifications
See table 2
Flow Characteristics
Standard Cages: Linear, quick opening, or equal
percentage
Whisper Trim
™
Screwed or Socket Welding: All available ASME B16.11
schedules that are consistent with CL600 per ASME
B16.34
Buttwelding: Consistent with ASME B16.25
Maximum Inlet Pressure
(1)
Cast Iron Valves
Flanged: Consistent with CL125B or 250B
pressure‐temperature ratings per ASME B16.1
Steel and Stainless Steel Valves
Flanged: Consistent with CL150, 300, and 600
(2)
pressure‐temperature ratings per ASME B16.34
Screwed or Welding: Consistent with CL600
pressure‐temperature ratings per ASME B16.34
1. The pressure/temperature limits in this manual and any applicable standard or code limitation for the valve should not be exceeded.
2. Certain bonnet bolting material selections may require a CL600 easy‐e valve assembly to be derated. Contact your Emerson sales office
Flow Directions
Standard Cages: Normally up
Whisper Trim and WhisperFlo Cages: Always up
Approximate Weights
VALVE SIZE, NPS
1/2 and 3/4
1 and 1‐1/4
1‐1/2
2
2‐1/2
3
4
6
8
and WhisperFlo™ Cages: Linear
WEIGHT
kg Pounds
11
14
20
39
45
54
77
459
408
or Local Business Partner.
25
30
45
67
100
125
170
350
900
Description
These single‐port valves have cage guiding, quick‐change trim, and unbalanced push‐down‐to‐close valve plug action.
Valve configurations are as follows:
ES—Globe style valve (figure 1) with metal‐to‐metal seating as standard for all general applications over a wide range
of pressure drops and temperatures, and metal‐to‐PTFE seating is optional for more stringent shutoff requirements.
EAS—Angle valve version of ES, used to facilitate piping or in applications where a self draining valve body is required.
Specifications
Typical specifications for these valves are shown in table 1.
Installation
WARNING
Always wear protective gloves, clothing, and eyewear when performing any installation operations to avoid personal
injury.
Personal injury or equipment damage caused by sudden release of pressure may result if the valve assembly is installed
where service conditions could exceed the limits given in table 1 or on the appropriate nameplates. To avoid such injury or
damage, provide a relief valve for over‐pressure protection as required by government or accepted industry codes and
good engineering practices.
2
Page 3
Instruction Manual
D100397X012
Check with your process or safety engineer for any additional measures that must be taken to protect against process
media.
If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this
instruction manual.
ES Valve
July 2017
Table 2. Available Shutoff Classifications per ANSI/FCI 70‐2 and IEC 60534‐4
Seating Shutoff Class
Metal
PTFE VI
IV (standard)
V
CAUTION
When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature,
pressure drop, and controlled fluid conditions. Since some body/trim material combinations are limited in their pressure
drop and temperature ranges, do not apply any other conditions to the valve without first contacting your Emerson sales
office or Local Business Partner.
Before installing the valve, inspect the valve and pipelines for any damage and any foreign material which may cause
product damage.
1. Before installing the valve, inspect the valve and associated equipment for any damage and any foreign material.
2. Make certain the valve body interior is clean, that pipelines are free of foreign material, and that the valve is
oriented so that pipeline flow is in the same direction as the arrow on the side of the valve.
3. The control valve assembly may be installed in any orientation unless limited by seismic criteria. However, the
normal method is with the actuator vertical above the valve. Other positions may result in uneven valve plug and
cage wear, and improper operation. With some valves, the actuator may also need to be supported when it is not
vertical. For more information, consult your Emerson sales office or Local Business Partner.
4. Use accepted piping and welding practices when installing the valve in the line. Internal elastomeric parts may stay
in place during the welding procedure. For flanged valves, use a suitable gasket between the valve and pipeline
flanges.
CAUTION
Depending on valve body materials used, post weld heat treating may be required. If so, damage to internal elastomeric
and plastic parts, as well as internal metal parts is possible. Shrunk‐fit pieces and threaded connections may also loosen. In
general, if post weld heat treating is to be performed, all trim parts should be removed. Contact your Emerson sales office
or Local Business Partner for additional information.
5. With a leak‐off bonnet construction, remove the pipe plugs (keys 14 and 16, figure 8) to hook up the leak‐off
piping. If continuous operation is required during inspection or maintenance, install a three‐valve bypass around
the control valve assembly.
6. If the actuator and valve are shipped separately, refer to the actuator mounting procedure in the appropriate
actuator instruction manual.
WARNING
Personal injury could result from packing leakage. Valve packing was tightened before shipment; however, the packing
might require some readjustment to meet specific service conditions.
3
Page 4
ES Valve
July 2017
Instruction Manual
D100397X012
Valves with ENVIRO‐SEAL live‐loaded packing or HIGH‐SEAL Heavy‐Duty live‐loaded packing will not require this initial
re‐adjustment. See the Fisher instruction manuals titled ENVIRO‐SEAL Packing System for Sliding‐Stem Valves or
Heavy‐Duty Live‐Loaded Packing System (as appropriate) for packing instructions. If you wish to convert your present
packing arrangement to ENVIRO‐SEAL packing, refer to the retrofit kits listed in the Parts Kits sub‐section near the end
of this manual.
Maintenance
Valve parts are subject to normal wear and must be inspected and replaced as necessary. Inspection and maintenance
frequency depends on the severity of service conditions. This section includes instructions for packing lubrication,
packing maintenance, trim maintenance, and ENVIRO‐SEAL bellows seal replacement. All maintenance operations
may be performed with the valve in the line.
WARNING
Avoid personal injury or damage to property from sudden release of pressure or uncontrolled process fluid. Before starting
disassembly:
D Do not remove the actuator from the valve while the valve is still pressurized.
D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal
injury.
D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the
actuator cannot suddenly open the valve.
D Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure
on both sides of the valve. Drain the process media from both sides of the valve.
D Vent the power actuator loading pressure and relieve any actuator spring compression.
D Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.
D The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from the
pipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or when
loosening the packing box pipe plug.
D Check with your process or safety engineer for any additional measures that must be taken to protect against process
media.
CAUTION
Follow instructions carefully to avoid damaging the product surfaces, which could result in damage to the product.
Note
Whenever a gasket seal is disturbed by removing or shifting gasketed parts, a new gasket should be installed upon reassembly.
This is necessary to ensure a good gasket seal since the used gasket may not seal properly.
Note
If the valve has ENVIRO‐SEAL or HIGH‐SEAL live‐loaded packing installed, refer to instruction manuals ENVIRO‐SEAL Packing
System for Sliding‐Stem Valves, D101642X012, or HIGH‐SEAL Live‐Loaded Packing System, D101453X012
4
, for packing
Page 5
Instruction Manual
D100397X012
ES Valve
July 2017
instructions. Figure 9 shows a typical HIGH‐SEAL Packing system. Figures 10, 11, and 12 show typical ENVIRO‐SEAL packing
systems.
If the valve has an ENVIRO‐SEAL bellows seal bonnet installed, refer to this manual. See the ENVIRO‐SEAL Bellows Seal and Bonnet
section for information on the bellows seal bonnet.
Figure 2. Optional Lubricator and Lubricator/Isolating Valve
10A9421‐A
AJ5428‐D
A0832‐2
LUBRICATOR LUBRICATOR/ISOLATING VALVE
Table 3. Body‐to‐Bonnet Bolt Torque Guidelines
VALVE SIZE, NPS BOLT TORQUES
ES EAS
1‐1/4 or less 1 129 95 64 47
1‐1/2, 1‐1/2 x 1, 2, or 2 x 1 2 or 2 x 1 96 71 45 33
2‐1/2 or 2‐1/2 x 1‐1/2 3 or 3 x 1‐1/2 129 95 64 47
3, 3 x 2, or 3 x 2‐1/2 4 or 4 x 2 169 125 88 65
4, 4 x 2‐1/2, or 4 x 3 6 or 6 x 2‐1/2 271 200 156 115
6 ‐ ‐ ‐ 549 405 366 270
8 ‐ ‐ ‐ 746 550 529 390
1. Determined from laboratory tests.
2. SA193‐B8M annealed.
3. SA193‐B8M strain hardened.
4. For other materials, contact your Emerson sales office
or Local Business Partner for torques.
Packing Lubrication
Note
ENVIRO‐SEAL or HIGH‐SEAL packing does not require lubrication.
(1, 4)
SA193‐B7, SA193‐B8M
NSm LbfSft NSm LbfSft
(3)
SA193‐B8M
(2)
WARNING
To avoid personal injury or property damage resulting from fire or explosion, do not lubricate packing used in oxygen
service or in processes with temperatures over 260_C (500_F).
If a lubricator or lubricator/isolating valve (figure 2) is provided for PTFE/composition or other packings that require
lubrication, it will be installed in place of the pipe plug (key 14, figure 8). Use a good quality silicon‐base lubricant.
Packing used in oxygen service or in processes with temperatures over 260_C (500_F) should not be lubricated. To
operate the lubricator, simply turn the cap screw clockwise to force the lubricant into the packing box. The
lubricator/isolating valve operates the same way except the isolating valve must first be opened and then closed after
lubrication is completed.
5
Page 6
ES Valve
July 2017
Instruction Manual
D100397X012
Packing Maintenance
Key numbers refer to figure 3 for PTFE V‐ring packing and to figure 5 for PTFE/composition packing, unless otherwise
indicated.
For spring‐loaded single PTFE V‐ring packing, the spring (key 8, figure 3) maintains a sealing force on the packing. If
leakage is noted around the packing follower (key 13, figure 3), check to be sure the shoulder on the packing follower
is touching the bonnet. If the shoulder is not touching the bonnet, tighten the packing flange nuts (key 5, figure 8)
until the shoulder is against the bonnet. If leakage cannot be stopped in this manner, proceed to the replacing packing
procedure.
If there is undesirable packing leakage with other than spring‐loaded packing, first try to limit the leakage and
establish a stem seal by tightening the packing flange nuts.
If the packing is relatively new and tight on the stem, and if tightening the packing flange nuts does not stop the
leakage, it is possible that the valve stem is worn or nicked so that a seal cannot be made. The surface finish of a new
valve stem is critical for making a good packing seal. If the leakage comes from the outside diameter of the packing, it
is possible that the leakage is caused by nicks or scratches around the packing box wall. If performing any of the
following procedures, inspect the valve stem and packing box wall for nicks and scratches.
Replacing Packing
WARNING
Refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
1. Isolate the control valve from the line pressure, and release pressure from the valve.
2. Disconnect the operating lines from the actuator and any leak‐off piping from the bonnet. Disconnect the stem
connector, then remove the actuator from the valve by unscrewing the yoke locknut (key 15, figure 8) or the hex
nuts (key 26, figure 8).
WARNING
To avoid personal injury or property damage caused by uncontrolled movement of the bonnet, loosen the bonnet by
following the instructions in the next step. Do not remove a stuck bonnet by pulling on it with equipment that can stretch
or store energy in any other manner. The sudden release of stored energy can cause uncontrolled movement of the bonnet.
If the cage sticks to the bonnet, proceed carefully with bonnet removal.
Note
The following step also helps to provide additional assurance that the valve body fluid pressure has been relieved.
3. Hex nuts (key 5, figure 8) attach the bonnet to the valve. Loosen these nuts or cap screws approximately 3 mm (1/8
inch). Then loosen the body‐to‐bonnet gasketed joint by either rocking the bonnet or prying between the bonnet
and valve body. Work the prying tool around the bonnet until the bonnet loosens.
6
Page 7
Instruction Manual
D100397X012
Figure 3. PTFE V‐Ring Packing Arrangements for Plain and Extension Bonnets
ES Valve
July 2017
UPPER WIPER
(KEY 12)
PACKING
FOLLOWER
(KEY 13)
WASHER
(KEY 10)
SPRING
(KEY 8)
PACKING BOX
RING (KEY 11)
12A7837−A
FOR S31600 OR S17400
METAL PACKING BOX PARTS
NOTE:
1
PART OF PACKING SET (KEY 6) (SEE TABLE IN PARTS LIST).
B2427
FEMALE
ADAPTOR
PACKING RING
MALE
ADAPTOR
LOWER WIPER
1
1
1
1
SINGLE ARRANGEMENTS
1
FEMALE
ADAPTOR
1
PACKING RING
1
MALE
ADAPTOR
1
LOWER WIPER
FOR ALL OTHER METAL PACKING
BOX PART MATERIALS
UPPER WIPER
(KEY 12)
PACKING
FOLLOWER
(KEY 13)
SPACER
(KEY 8)
PACKING BOX
RING (KEY 11)
UPPER WIPER
(KEY 12)
PACKING
FOLLOWER
(KEY 13)
MALE ADAPTOR
(KEY 31)
PACKING RING
(KEY 7)
FEMALE ADAPTOR
(KEY 32)
LANTERN RING
(KEY 8)
12A8187-D 12A7814-D 12A7839-A
ASSEMBLY 1
(POSITIVE
PRESSURES)
ASSEMBLY 2
(VACUUM)
ASSEMBLY 3
(POSITIVE
PRESSURES
& VACUUM)
ASSEMBLY 1
(POSITIVE
PRESSURES)
9.5 mm (3/8 INCH) STEM 12.7 mm (1/2 INCH) STEM
B1428‐3
ASSEMBLY 2
(VACUUM)
ASSEMBLY 3
(POSITIVE
PRESSURES
& VACUUM)
DOUBLE ARRANGEMENTS
ASSEMBLY 1
(POSITIVE
PRESSURES)
ASSEMBLY 2
(VACUUM)
19.1, 25.4, or 31.8 mm
(3/4, 1, OR 1‐1/4 INCH) STEM
ASSEMBLY 3
(POSITIVE
PRESSURES
& VACUUM)
PACKING BOX
RING (KEY 11)
LOWER WIPER
(KEY 30)
7
Page 8
ES Valve
July 2017
Figure 4. PTFE Packing Arrangements for Use in ENVIRO‐SEAL Bellows Seal Bonnets
UPPER WIPER
(KEY 12)
BUSHING (KEY 13)
PACKING SET: (KEY 6)
FEMALE ADAPTOR
PACKING RING
MALE ADAPTOR
SPACER
THRUST
(KEY 39)
SPRING
(KEY 8)
THRUST
12B4182-A SHT 1
(KEY 39)
9.5 mm
(3/8 INCH)
STEM
FOR S31600 (316 SST)
PACKING BOX PARTS
BUSHING
(KEY 13)
RING
RING
12B4185-A SHT 1
12.7 mm
(1/2 INCH)
STEM
SINGLE ARRANGEMENTS
BUSHING
(KEY 13)
SPACER
(KEY 8)
12B4182-A SHT 2
9.5 mm
(3/8 INCH)
STEM
MATERIALS EXCEPT S31600
UPPER WIPER
(KEY 12)
BUSHING (KEY 13)
PACKING SET: (KEY 6)
FEMALE ADAPTOR
PACKING RING
MALE ADAPTOR
(KEY 8)
SPACER
(KEY 8)
12B4185-A SHT 2
12.7 mm
(1/2 INCH)
FOR ALL PACKING BOX
STEM
Instruction Manual
D100397X012
SPACER
(KEY 8)
THRUST
12B4183-A 18A0906-D 18A5338-A
9.5 mm
(3/8 INCH)
STEM
RING
(KEY 39)
12.7 mm
(1/2 INCH)
STEM FOR
NPS 2 VALVES
12.7 mm
(1/2 INCH)
STEM FOR
NPS 3 AND 4
VALVES
A5863‐1
DOUBLE ARRANGEMENTS
4. Loosen the packing flange nuts (key 5, figure 8) so that the packing is not tight on the valve stem. Remove any
travel indicator parts from the valve stem threads.
CAUTION
Avoid damage to the seating surface caused by the valve plug and stem assembly dropping from the bonnet after being
lifted part way out. When lifting the bonnet, temporarily install a valve stem locknut on the valve stem. This locknut will
prevent the valve plug and stem assembly from dropping out of the bonnet.
If the cage starts to lift with the bonnet, tap it with a plastic mallet, or other soft material, to be sure it stays in the valve.
5. Completely remove the cap screws (not shown) or hex nuts (key 16; figure 13, 14, or 15) that bolt the bonnet and
valve together and carefully lift the bonnet off.
6. Remove the locknut and separate the valve plug and stem from the bonnet. Set the parts on a protective surface to
prevent damage to gasket or seating surfaces.
8
Page 9
Instruction Manual
G
G
G
X
G
X
D100397X012
ES Valve
July 2017
Figure 5. Detail of PTFE/Composition Packing
Arrangements for Plain and Extension Bonnets
UPPER WIPER
(KEY 12)
PACKING
FOLLOWER (KEY 13)
PACKING RING
(KEY 7)
LANTERN RING
(KEY 8)
PACKING BOX
RING (KEY 11)
12A8188‐A
12A7815‐A
12A8173‐A
A2619‐2
9.5 mm
(3/8 INCH)
STEM
12.7 mm
(1/2 INCH)
STEM
19.1, 25.4, OR
31.8 mm
(3/4, 1, OR
1‐1/4 INCH)
STEM
TYPICAL (DOUBLE) ARRANGEMENTS
Figure 6. Double Graphite Ribbon/Filament Arrange
ments for use in ENVIRO‐SEAL Bellows Seal Bonnets
BUSHING
12.7 mm
(KEY 13)
GRAPHITE
FILAMENT
PACKING RING
(KEY 7)
GRAPHITE
RIBBON
PACKING RING
(KEY 7)
SPACER
(KEY 8)
1
1
1
1
12B4181-A
9.5 mm
(3/8 INCH)
STEM
NOTE:
1
0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS;
USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING.
A5870‐1
18A0909-D
12.7 mm
(1/2 INCH)
STEM FOR
NPS 2 VALVES
1
1
12B6102-A
NPS 3 AND 4 VALVES
(1/2 INCH)
STEM FOR
Figure 7. Detail of Graphite Ribbon/Filament Packing
for Plain and Extension Bonnets
PACKING
FOLLOWER
(KEY 13)
GRAPHITE
RIBBON
PACKING RIN
1
19.1, 25.4, & 31.8 mm
1
14A3411-A
(3/8 INCH)
9.5 mm
STEM
1
13A9775-B
12.7 mm
(1/2 INCH)
STEM
SINGLE ARRANGEMENTS
1
1
19.1, 25.4, & 31.8 mm
1
14A2153-B
9.5 mm
(3/8 INCH)
STEM
1
14A1849-B
(1/2 INCH)
12.7 mm
STEM
DOUBLE ARRANGEMENTS
NOTE:
1
0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS;
USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING.
A5864‐1
13A9776-B
(3/4, 1 & 1‐1/4 INCH)
STEM
14A1780-B
(3/4, 1 & 1‐1/4 INCH)
STEM
(KEY 7)
GRAPHITE
FILAMENT
PACKING RIN
(KEY 7)
LANTERN
RING (KEY 8)
PACKING BO
RING (KEY 11)
PACKING
FOLLOWER
(KEY 13)
GRAPHITE
RIBBON
PACKING RIN
(KEY 7)
GRAPHITE
FILAMENT
PACKING RIN
(KEY 7)
LANTERN
RING (KEY 8)
PACKING BO
RING (KEY 11)
WARNING
To avoid personal injury due to leaking fluid, avoid damaging gasket sealing surfaces. The seating surface of the valve plug
(key 2) is critical for proper shutoff. Protect these surfaces accordingly.
9
Page 10
ES Valve
July 2017
Instruction Manual
D100397X012
CAUTION
To prevent possible product damage, cover the opening in the valve in the following procedure to prevent foreign material
from getting into the valve body cavity.
7. Remove the bonnet gasket (key 10, figure 13 through 15) and cover the opening in the valve to protect the gasket
surface and prevent foreign material from getting into the valve body cavity.
8. Remove the packing flange nuts, packing flange, upper wiper, and packing follower (keys 5, 3, 12, and 13, figure 8).
Carefully push out all the remaining packing parts from the valve side of the bonnet using a rounded rod or other
tool that will not scratch the packing box wall. Clean the packing box and the metal packing parts.
9. Inspect the valve stem threads and packing box surfaces for any sharp edges which might cut the packing.
Scratches or burrs could cause packing box leakage or damage to the new packing. If the surface condition cannot
be improved by light sanding, replace the damaged parts by following the appropriate steps in the Trim
Maintenance procedure.
10. Remove the covering protecting the valve body cavity and install a new bonnet gasket (key 10, figure 13 through
15), making sure the gasket seating surfaces are clean and smooth. Then slide the bonnet over the stem and onto
the stud bolts (key 15, figure 13, 14, or 15) or onto the valve body cavity if cap screws (not shown) will be used
instead.
Note
Proper performance of the bolting procedures in step 11 compresses the spiral wound gasket (key 12, figure 13 through 15) or
load ring (key 26, figure 14) enough to both load and seal the seat ring gasket (key 13, figure 13, 14, or 15). It also compresses the
outer edge of the bonnet gasket (key 10, figure 13 through 15) enough to seal the body‐to‐bonnet joint.
The proper bolting procedures in step 11 include‐‐but are not limited to‐‐ensuring that bolting threads are clean, and evenly
tightening the cap screws, or the nuts onto the studs, in a crisscross pattern. Because of the boltup characteristics of spiral wound
gaskets, tightening one cap screw or nut may loosen an adjacent cap screw or nut. Repeat the crisscross tightening pattern several
times until each cap screw or nut is tight and the body‐to‐bonnet seal is made. When the operating temperature has been
reached, perform this torquing procedure once again.
11. Install bolting, using proper bolting procedures during tightening so that the body‐to‐bonnet joint will withstand
test pressures and application service conditions. The bolt torques in table 3 may be used as guidelines.
12. Install new packing and the metal packing box parts according to the appropriate arrangement in figure 3, 5, or 7.
For split ring packing, alternate the positions of the splits to avoid creating a leak path. Place a smooth‐edged pipe
over the valve stem and gently tap each soft packing part into the packing box, being sure that air is not trapped
between adjacent soft parts.
13. Slide the packing follower, upper wiper, and packing flange (keys 13, 12, and 3, figure 8) into position. Lubricate
the packing flange studs (key 4, figure 8) and the faces of the packing flange nuts (key 5, figure 8). Install the
packing flange nuts.
14. For spring‐loaded PTFE V‐ring packing, tighten the packing flange nuts until the shoulder on the packing follower
(key 13, figure 8) contacts the bonnet.
For ENVIRO‐SEAL or HIGH‐SEAL live‐loaded packing, refer to the note at the beginning of the Maintenance section.
For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 4. Then,
loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 4.
For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nuts
reaches the minimum recommended torque shown in table 4. Then, tighten the remaining flange nuts until the
packing flange is level and at a 90‐degree angle to the valve stem.
10
Page 11
Instruction Manual
D100397X012
ES Valve
July 2017
15. Mount the actuator on the valve assembly and reconnect the actuator and valve stem according to the procedure
in the appropriate actuator instruction manual.
Trim Maintenance
WARNING
Refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
CAUTION
In the following applicable procedures, to avoid damaging parts, do not grip the bellows shroud or other parts of the
stem/bellows assembly. Grip only the flat areas on the stem where it extends out of the top of the bellows shroud.
Except where indicated, key numbers in this section are referenced in figure 13 for standard NPS 1/2 through 6
constructions, figure 14 for NPS 8 ES valves, figure 15 for Whisper Trim III cage detail, and figure 16 for WhisperFlo
trim.
Disassembly
1. Remove the actuator and the bonnet according to steps 1 through 6 of the Replacing Packing procedure of the
Maintenance section.
Table 4. Recommended Torque for Packing Flange Nuts (Not for Spring‐Loaded Packing)
VALVE STEM DIAMETER
mm Inches NSm LbfSin NSm LbfSin NSm LbfSin NSm LbfSin
9.5 3/8
12.7 1/2
19.1 3/4
25.4 1
31.8 1‐1/4
PRESS‐URE
RATING
CL125,
150
CL250,
300
CL600 5 48 8 72 3 24 4 36
CL125,
150
CL250,
300
CL600 10 84 14 120 5 42 7 60
CL125,
150
CL250,
300
CL600 20 180 30 264 10 90 15 132
CL300 24 216 37 324 12 108 16 144
CL600 34 300 50 444 16 144 24 216
CL300 33 288 49 432 16 144 24 216
CL600 45 396 66 588 22 192 33 288
Minimum Torque Maximum Torque Minimum Torque Maximum Torque
11 96 16 144 5 48 8 72
14 120 20 180 7 60 10 90
GRAPHITE TYPE PACKING PTFE TYPE PACKING
3 24 5 48 1 12 3 24
4 36 7 60 2 18 3 30
5 48 8 72 3 24 4 36
7 60 10 84 3 30 5 42
11
Page 12
ES Valve
July 2017
Instruction Manual
D100397X012
WARNING
To avoid personal injury due to leaking fluid, avoid damaging gasket sealing surfaces. The surface finish of the valve stem
(key 7) is critical for making a good packing seal. The inside surface of the cage or cage/baffle assembly (key 3), or cage
retainer (key 31), is critical for smooth operation of the valve plug. The seating surfaces of the valve plug (key 2) and seat
ring (key 9) are critical for proper shutoff. Unless inspection reveals otherwise, assume all these parts are in good condition
and protect them accordingly.
2. Packing parts can be removed if desired. Replace these parts as described in the Replacing Packing procedure.
Remove the load ring (key 26) from an NPS 8 ES valve, or the cage adaptor (key 4) from any restricted trim valve,
and wrap it for protection.
3. Lift the valve plug and stem assembly out of the valve and set it on a protective surface. If the valve plug is to be
reused, protect the valve plug seating surface to prevent scratches. On an NPS 6 ES valve with Whisper Trim III cage
or WhisperFlo trim, also remove the bonnet spacer (key 32) and bonnet gasket (key 10) on top of the spacer. Then
on any construction with a cage retainer (key 31), remove the cage retainer and its associated gaskets.
A Whisper Trim III and WhisperFlo trim cage retainer has two 3/8 inch‐16 UNC tappings in which screws or bolts can be
installed for lifting.
4. Remove the cage or cage/baffle assembly (key 3), the associated gaskets (keys 10, 11, and 12), and shim (key 51 for
the ES valve, key 27 for the EAS valve). If the cage is stuck in the valve body, use a rubber mallet to strike the
exposed portion of the cage at several points around its circumference.
5. Remove the seat ring or liner (key 9) or disk seat (key 22), seat ring gasket (key 13), and the seat ring adaptor (key 5)
and adaptor gasket (key 14) where used in a restricted trim seat ring construction. PTFE seat constructions use a
disk (key 23) sandwiched between the disk seat and disk retainer (key 21).
6. Inspect parts for wear or damage which would prevent proper operation of the valve. Replace or repair trim parts
according to the following procedure for lapping metal seats or other valve plug maintenance procedures as
appropriate.
Table 5. Valve Stem Connection Torque and Pin Replacement
VALVE STEM CONNECTION (VSC) BOLT TORQUE, MINIMUM TO MAXIMUM HOLE SIZE
mm Inches NSm LbfSft mm Inch
9.5
12.7
19.1
25.4
31.8
3/8
1/2
3/4
1
1‐1/4
40‐47
81‐115
237‐339
420‐481
827‐908
25‐35
60‐85
175‐250
310‐355
610‐670
2.41 ‐ 2.46
3.20 ‐ 3.25
4.80 ‐ 4.88
6.38 ‐ 6.45
6.38 ‐ 6.45
0.095 ‐ 0.097
0.126 ‐ 0.128
0.189 ‐ 0.192
0.251 ‐ 0.254
0.251 ‐ 0.254
Table 6. Standard Material Designations
Standard Designation Common Name or Trade Name
CoCr‐A Hardfacing Alloy
R30006
S17400 SST
S31600 SST
S41000, S41600, CA15
WCC Carbon Steel Casting
CoCr‐A
Alloy 6 Casting
17‐4PH Stainless Steel
316 Stainless Steel
13Cr 400‐Series SST
WCC
CAUTION
To avoid damaging the ENVIRO‐SEAL bellows seal bonnet assembly, do not attempt to lap the metal seating surfaces. The
design of the assembly prevents rotation of the stem and any forced lapping rotation will damage internal components of
the ENVIRO‐SEAL bellows seal bonnet.
12
Page 13
Instruction Manual
D100397X012
ES Valve
July 2017
Lapping Metal Seats
A certain amount of leakage should be expected with metal‐to‐metal seating in any valve body. If the leakage
becomes excessive, however, the condition of the seating surfaces of the valve plug and seat ring can be improved by
lapping. (Deep nicks should be machined out rather than ground out.) Use a good quality lapping compound of a
mixture of 280 to 600‐grit. Apply the compound to the bottom of the valve plug.
Assemble the valve to the extent that the cage and the cage retainer and bonnet spacer (if used) are in place and the
bonnet is bolted to the valve body. A simple handle can be made from a piece of strap iron locked to the valve plug
stem with nuts. Rotate the handle alternately in each direction to lap the seats. After lapping, remove the bonnet and
clean the seat surfaces. Completely assemble as described in the assembly portion of the trim maintenance procedure
and test the valve for shutoff. Repeat the lapping procedure if leakage is still excessive.
CAUTION
To avoid weakening the stem or adaptor that may cause failure in service, never reuse an old stem or adaptor with a new
valve plug. Using an old stem or adaptor with a new plug requires drilling a new pin hole in the stem (or adaptor in case an
ENVIRO‐SEAL bellows seal bonnet is being used), which will weaken the stem. However, a used valve plug may be reused
with a new stem or adaptor.
Valve Plug Maintenance
Except where indicated, key numbers are referenced in figure 13 for NPS 1/2 through 6 constructions, figure 14 for
NPS 8 ES valves, figure 15 for Whisper Trim III cage detail, and figure 16 for WhisperFlo trim.
1. Remove the valve plug (key 2) according to the disassembly portion of the trim maintenance procedure.
2. To replace the valve stem (key 7), drive out the pin (key 8). Unscrew the valve plug from the stem or adaptor.
3. To replace the adaptor (key 24, figure 8) on ENVIRO‐SEAL bellows seal bonnets, place the plug stem assembly and
valve plug in a soft‐jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a
seating surface. Drive out or drill out the pin (key 36, figure 8). Reverse the plug stem assembly in the soft‐jaw
chuck or vise. Grip the flat areas on the valve stem just below the threads for the actuator/stem connection.
Unscrew the valve plug/adaptor assembly (key 24, figure 8) from the valve stem assembly (key 20, figure 8).
4. Screw the stem or adaptor into the valve plug. Tighten to the torque value given in table 5. Refer to table 5 to select
the proper hole size. Drill through the stem or adaptor, using the hole in the valve plug as a guide. Remove any
chips or burrs and drive in a new pin to lock the assembly.
5. For ENVIRO‐SEAL bellows seal bonnets, grip the flats of the stem extending out of the top of the bellows shroud
with a soft‐jaw chuck or other type of vise. Screw the valve plug/adaptor assembly onto the valve stem. Tighten as
necessary to align the pin hole in the stem with one of the holes in the adaptor. Secure the adaptor to the stem with
a new pin.
Assembly
Except where indicated, key numbers are referenced in figure 13 for standard NPS 1/2 through 6 constructions, figure
14 for NPS 8 ES valves, figure 15 for Whisper Trim III cage detail, and figure 16 for WhisperFlo trim.
1. With a restricted trim seat ring construction, install the adaptor gasket (key 14) and seat ring adaptor (key 5).
2. Install the seat ring gasket (key 13), seat ring or liner (key 9), or disk seat (key 22). With a PTFE seat construction,
install the disk and disk retainer (keys 21 and 23).
3. Install the cage or cage/baffle assembly (key 3). Any rotational orientation of the cage or assembly with respect to
the valve is acceptable. A Whisper Trim III cage designated by level A3, B3, or C3 may be installed with either end
13
Page 14
ES Valve
July 2017
Instruction Manual
D100397X012
up. The level D3 cage/baffle assembly, however, must be installed with the hole pattern end next to the seat ring. If
a cage retainer (key 31) is to be used, place it on top of the cage.
4. Slide the valve plug (key 2) and stem assembly, or valve plug and ENVIRO‐SEAL bellows seal assembly, into the cage.
5. Place the gaskets (key 10, or keys 11, 12 and 14, if used) and the shim (key 27 or key 51) on top of the cage or cage
retainer. If there is a cage adaptor (key 4) or a bonnet spacer (key 32), set it on the cage or cage retainer gaskets and
place another flat sheet gasket (key 10) on top of the adaptor or spacer. If there is only a cage retainer, place
another flat sheet gasket on the retainer.
6. With an NPS 8 ES valve, install the load ring (key 26).
CAUTION
To avoid damaging packing with the valve stem threads, use care when installing the bonnet if the packing was not
removed from the bonnet.
Table 7. Recommended Torque for ENVIRO‐SEAL Bellows Seal Packing Flange Nuts
VALVE SIZE VALVE STEM DIAMETER THROUGH PACKING MINIMUM TORQUE MAXIMUM TORQUE
NPS Inch NSm LbfSin NSm LbfSin
1/2 ‐ 2 1/2 3 24 5 48
3 ‐ 4 1 7 60 10 84
7. Mount the bonnet on the valve and complete assembly according to steps 10 through 14 of the Replacing Packing
procedure, omitting steps 11 and 12 if new packing is not being installed, and being sure to observe the note prior
to step 11.
ENVIRO‐SEAL Bellows Seal and Bonnet
Replacing a Plain or Extension Bonnet with an ENVIRO‐SEAL Bellows Seal (Stem/Bellows
Assembly) and Bonnet
1. Remove the actuator and bonnet according to steps 1 through 6 of the Replacing Packing procedure of the
Maintenance section.
2. With care, remove the valve plug and stem assembly from the valve body. If necessary, lift out the cage, also.
CAUTION
To prevent possible product damage, cover the opening in the valve in the following procedure to protect the sealing
surfaces and to prevent foreign material from getting into the valve body cavity.
3. Remove and discard the existing bonnet gasket. Cover the valve body opening to protect sealing surfaces and to
prevent foreign material from entering the valve body cavity.
Note
The ENVIRO‐SEAL stem/bellows assembly for easy‐e valves is available only with a threaded and drilled plug/adaptor/stem
connection. The existing valve plug can be reused with the new stem/bellows assembly or a new plug can be installed.
14
Page 15
Instruction Manual
D100397X012
ES Valve
July 2017
4. Inspect the existing valve plug. If the plug is in good condition, it can be reused with the new ENVIRO‐SEAL
stem/bellows assembly. To remove the existing valve plug from the stem, first, place the existing plug stem
assembly and valve plug in a soft‐jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that
is not a seating surface. Drive out or drill out the pin (key 8).
5. Then, reverse the plug stem assembly in the soft‐jaw chuck or vise. Grip the valve stem in an appropriate place and
unscrew the existing plug from the valve stem.
CAUTION
When installing a valve plug on the ENVIRO‐SEAL stem/bellows assembly, the valve stem must not be rotated. Damage to
the bellows may result.
To avoid damaging parts, do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat
areas on the stem where it extends out of the top of the bellows shroud.
Note
The ENVIRO‐SEAL stem/bellows assembly has a one‐piece stem.
6. To attach the valve plug to the stem of the new ENVIRO‐SEAL stem/bellows assembly, it is necessary to first attach
the plug to the adaptor (key 24). Locate the adaptor. Notice that a hole has not been drilled in the threads where
the plug screws onto the adaptor. Secure the valve plug in a soft‐jaw chuck or other type of vise. Do not grip the
plug on any seating surface. Position the plug in the chuck or vise for easy threading of the adaptor. Thread the
adaptor into the valve plug and tighten to the appropriate torque value.
7. Select the proper size of drill bit and drill through the adaptor using the hole in the valve plug as a guide. Remove
any metal chips or burrs and drive in a new pin to lock the plug/adaptor assembly together.
8. Attach the plug/adaptor assembly to the ENVIRO‐SEAL stem/bellows assembly by first securing the stem/bellows
assembly in a soft‐jaw chuck or other type of vise so that the jaws of the chuck or vise grip the flats of the stem
extending out of the top of the bellows shroud. Screw the valve plug/adaptor assembly onto the valve stem.
Tighten as necessary to align the pin hole in the stem with one of the holes in the adaptor. Secure the adaptor to the
stem with a new pin.
9. Inspect the seat ring (key 9) and soft seat parts (keys 21, 22, and 23). Replace, if necessary.
10. Place a new gasket (key 10) into the valve body in place of the bonnet gasket. Install the new stem/bellows
assembly with valve plug/adaptor by placing it into the valve body on top of the new bellows gasket.
11. Place a new gasket (key 22) over the stem/bellows assembly. Place the new ENVIRO‐SEAL bonnet over the
stem/bellows assembly.
Note
Stud(s) and nut(s) should be installed such that the manufacturer's trademark and material grade marking is visible, allowing easy
comparison to the materials selected and documented in the Emerson/Fisher serial card provided with this product.
WARNING
Personal injury or damage to equipment could occur if improper stud and nut materials or parts are used. Do not operate or
assemble this product with stud(s) and nut(s) that are not approved by Emerson/Fisher engineering and/or listed on the
serial card provided with this product. Use of unapproved materials and parts could lead to stresses exceeding the design
or code limits intended for this particular service. Install studs with the material grade and manufacturer's identification
15
Page 16
ES Valve
July 2017
mark visible. Contact your Emerson representative immediately if a discrepancy between actual parts and approved parts
is suspected.
Instruction Manual
D100397X012
12. Properly lubricate the bonnet stud bolts. Install and tighten the bonnet hex nuts to the proper torque.
13. Install new packing and the metal packing box parts according to the appropriate arrangement in figure 3.
14. Install the packing flange. Properly lubricate the packing flange stud bolts and the faces of the packing flange nuts.
For ENVIRO‐SEAL or HIGH‐SEAL live‐loaded packing, refer to the note at the beginning of the Maintenance section.
For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 7. Then,
loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 7.
For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nuts
reaches the minimum recommended torque shown in table 7. Then, tighten the remaining flange nuts until the
packing flange is level and at a 90‐degree angle to the valve stem.
15. Install travel indicator parts, stem locknuts, and mount the actuator on the valve body according to the procedure
in the appropriate actuator instruction manual.
Replacement of an Installed ENVIRO‐SEAL Bellows Seal (Stem/Bellows Assembly)
1. Remove the actuator and bonnet according to steps 1 through 6 of the Replacing Packing procedure of the
Maintenance section.
CAUTION
To prevent possible product damage, cover the opening in the valve in the following procedure to protect the sealing
surfaces and to prevent foreign material from getting into the valve body cavity.
2. With care, remove the ENVIRO‐SEAL stem/bellows assembly. If necessary, lift out the cage, also. Remove and
discard the existing bonnet gasket and bellows gasket. Cover the valve body opening to protect sealing surfaces
and to prevent foreign material from entering the valve body cavity.
Note
The ENVIRO‐SEAL stem/bellows assembly for easy‐e valves is available only with a threaded and drilled plug/adaptor/stem
connection. The existing valve plug can be reused with the new stem/bellows assembly or a new plug can be installed.
3. Inspect the existing valve plug. If the plug is in good condition, it can be reused with the new stem/bellows
assembly.
CAUTION
When removing/installing a valve plug on the ENVIRO‐SEAL stem/bellows assembly, the valve stem must not be rotated.
Damage to the bellows may result.
To avoid damaging parts, do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat
areas on the stem where it extends out of the top of the bellows shroud.
16
Page 17
Instruction Manual
D100397X012
Note
The ENVIRO‐SEAL stem/bellows assembly has a one‐piece stem.
4. To remove the existing valve plug from the stem, first, place the existing plug stem assembly and valve plug in a
soft‐jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a seating surface.
Drive out or drill out the pin.
5. Then, reverse the plug stem assembly in the soft‐jaw chuck or vise. Grip the flat areas on the valve stem just below
the threads for the actuator/stem connection. Unscrew the existing plug from the valve stem.
6. To attach either the existing valve plug or a new one to the stem of the new ENVIRO‐SEAL stem/bellows assembly, it
is necessary to first attach the plug to the adaptor. Locate the adaptor. Notice that a hole has not been drilled in the
threads where the plug screws onto the adaptor. Secure the valve plug in a soft‐jaw chuck or other type of vise. Do
not grip the plug on any seating surface. Position the plug in the chuck or vise for easy threading of the adaptor.
Thread the adaptor into the valve plug and tighten to the appropriate torque value.
7. Complete the installation by following steps 7 through 9 and steps 12 through 15 of the ENVIRO‐SEAL Bellows Seal
and Bonnet installation instructions given above.
ES Valve
July 2017
Purging the ENVIRO‐SEAL Bellows Seal Bonnet
The ENVIRO‐SEAL bellows seal bonnet has been designed so that it can be purged or leak tested. Refer to figure 8 for
an illustration of an ENVIRO‐SEAL bellows seal bonnet, and perform the following steps for purging or leak testing.
1. Remove the two diametrically opposed pipe plugs (key 16).
2. Connect a purging fluid to one of the pipe plug connections.
3. Install appropriate piping or tubing in the other pipe plug connection to pipe away the purging fluid or to make a
connection to an analyzer for leak testing.
4. When purging or leak testing has been completed, remove the piping or tubing and reinstall the pipe plugs (key
16).
Parts Ordering
Each body‐bonnet assembly is assigned a serial number which can be found on the valve. This same number also
appears on the actuator nameplate when the valve is shipped from the factory as part of a control valve assembly.
Refer to the serial number when contacting your Emerson sales office
assistance. When ordering replacement parts, refer to the serial number and to the eleven‐character part number for
each part required from the following parts kit or parts list information.
Refer to table 6 for standard and common material designations.
or Local Business Partner for technical
WARNING
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should
not, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the
performance of the valve, and could cause personal injury and property damage.
Parts Kits
Note
Kits do not apply to alloy C (N10276 and CW2M), Alloy 20 (N08020 and CN7M), or alloy 400 (N04400 and M35‐1) trims.
17
Page 18
ES Valve
July 2017
Instruction Manual
Gasket Kits
Gasket Kits (includes keys 10, 11, 12, 13, and 51); plus 14 and 20 on Some Restricted Capacity Valves
DESCRIPTION
Full Capacity Valves Part Number Part Number
NPS 1/2, 3/4, 1, and 1‐1/4 (NPS 1 EAS)
NPS 1‐1/2 (NPS 2 EAS)
NPS 2
NPS 2‐1/2 (NPS 3 EAS)
NPS 3 (NPS 4 EAS)
NPS 4 (NPS 6 EAS)
NPS 6
NPS 8
Restricted Capacity Valves
w/ Metal Seating
NPS 1‐1/2 x 1 (NPS 2 x 1 EAS)
NPS 2 x 1
NPS 2‐1/2 x 1‐1/2 (NPS 3 x 1‐1/2 EAS)
NPS 3 x 2 (NPS 4 x 2 EAS)
NPS 4 x 2‐1/2 (NPS 6 x 2‐1/2 EAS)
Standard Trim Cage
Whisper Trim I Cage
-198 to 593_C (-325 to 1100_F) -198 to 593_C (-325 to 1100_F)
RGASKETX162
RGASKETX172
RGASKETX182
RGASKETX192
RGASKETX202
RGASKETX212
RGASKETX222
RGASKETX232
RGASKETX242
RGASKETX252
RGASKETX262
RGASKETX272
RGASKETX282
Whisper Trim III Cage
WhisperFlo Cage
RGASKETX422
RGASKETX432
RGASKETX442
RGASKETX452
RGASKETX462
RGASKETX472
RGASKETX482
10A3265X152
- - -
- - -
- - -
- - -
- - -
D100397X012
Packing Kits
Standard Packing Repair Kits (Non Live‐Loaded)
Stem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)
PTFE (Contains keys 6, 8, 10, 11, and 12) RPACKX00012 RPACKX00022 RPACKX00032 RPACKX00342 RPACKX00352
Double PTFE (Contains keys 6, 8, 11, and 12) RPACKX00042 RPACKX00052 RPACKX00062 RPACKX00362 RPACKX00372
PTFE/Composition (Contains keys 7, 8, 11, and 12) RPACKX00072 RPACKX00082 RPACKX00092 - - - - - -
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring], 8, and 11)
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring], and 11)
Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring])
Double Graphite Ribbon/Filament (Contains keys 7 [ribbon ring],
7 [filament ring], 8, and 11)
ENVIRO‐SEAL Packing Retrofit Kits
Retrofit kits include parts to convert valves with existing standard bonnets to the ENVIRO‐SEAL packing box
construction.
Refer to figure 10 for key numbers for PTFE packing, to figure 11 for key numbers for Graphite ULF packing, and to
figure 12 for key numbers for duplex packing.
PTFE kits include keys 200, 201, 211, 212, 214, 215, 217, 218, tag, and cable tie. Graphite ULF kits include keys 200,
201, 207, 208, 209, 210, 211, 212, 214, 216, 217, tag, and cable tie. Duplex kits include keys 200, 201, 207, 209, 211,
212, 214, 215, 216, 217, tag, and cable tie.
9.5 (3/8)
54 (2‐1/8)
RPACKX00102 RPACKX00112 RPACKX00122 - - - - - -
- - - - - - - - - RPACKX00532 RPACKX00542
RPACKX00132 RPACKX00142 RPACKX00152 - - - - - -
RPACKX00162 RPACKX00172 RPACKX00182 - - - - - -
12.7 (1/2)
71 (2‐13/16)
19.1 (3/4)
90 (3‐9/16)
25.4 (1)
127 (5)
31.8 (1-1/4)
127 (5, 5H)
Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and
design specifications may adversely alter the performance of this packing kit.
For part numbers of individual components in the ENVIRO‐SEAL packing kits, refer to instruction manual ENVIRO‐SEAL
Packing System for Sliding‐Stem Valves, D101642X012
18
.
Page 19
Instruction Manual
D100397X012
ES Valve
July 2017
ENVIRO‐SEAL Packing Retrofit Kits
PACKING
MATERIAL
Double PTFE RPACKXRT012 RPACKXRT022 RPACKXRT032 RPACKXRT042 RPACKXRT052
Graphite ULF RPACKXRT262 RPACKXRT272 RPACKXRT282 RPACKXRT292 RPACKXRT302
Duplex RPACKXRT212 RPACKXRT222 RPACKXRT232 RPACKXRT242 RPACKXRT252
9.5 (3/8)
54 (2‐1/8)
STEM DIAMETER AND YOKE BOSS DIAMETER, mm (INCH)
12.7 (1/2)
71 (2‐13/16)
19.1 (3/4)
90 (3‐9/16)
25.4 (1)
127 (5)
31.8 (1‐1/4)
127 (5, 5H)
ENVIRO‐SEAL Packing Repair Kits
Repair kits include parts to replace the “soft” packing materials in valves that already have ENVIRO‐SEAL packing
arrangements installed or in valves that have been upgraded with ENVIRO‐SEAL retrofit kits.
Refer to figure 10 for key numbers for PTFE packing, to figure 11 for key numbers for Graphite ULF packing, and to
figure 12 for key numbers for duplex packing.
PTFE repair kits include keys 214, 215, and 218. Graphite ULF repair kits include keys 207, 208, 209, 210, and 214.
Duplex repair kits include keys 207, 209, 214, and 215.
Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and
design specifications may adversely alter the performance of this packing kit.
For part numbers of individual components in the ENVIRO‐SEAL packing kits, refer to instruction manual ENVIRO‐SEAL
Packing System for Sliding‐Stem Valves, D101642X012
.
ENVIRO‐SEAL Packing Repair Kits
Stem Diameter, mm (Inches)
Yoke Boss Diameter, mm (Inches)
Double PTFE (Contains keys 214, 215, & 218) RPACKX00192 RPACKX00202 RPACKX00212 RPACKX00222 RPACKX00232
Graphite ULF (Contains keys 207, 208, 209, 210, and 214) RPACKX00592 RPACKX00602 RPACKX00612 RPACKX00622 RPACKX00632
Duplex (Contains keys 207, 209, 214, and 215) RPACKX00292 RPACKX00302 RPACKX00312 RPACKX00322 RPACKX00332
9.5 (3/8)
54 (2‐1/8)
12.7 (1/2)
71 (2‐13/16)
19.1 (3/4)
90 (3‐9/16)
25.4 (1)
127 (5)
31.8 (1‐1/4)
127 (5, 5H)
Parts List
Key Description Part Number
Note
Part numbers are shown for recommended spares only. For part
numbers not shown, contact your Emerson sales office
Partner.
or Local Business
Bonnet (figures 3‐12)
Key Description Part Number
1 Bonnet/ENVIRO‐SEAL bellows seal bonnet
If you need a bonnet or an ENVIRO‐SEAL bellows seal
bonnet as a replacement part, order by valve size and
stem diameter, serial number, and desired material.
2 Extension Bonnet Baffle
3 Packing Flange
3 ENVIRO‐SEAL bellows seal packing flange
4 Packing Flange Stud
4 ENVIRO‐SEAL bellows seal stud bolt
5 Packing Flange Nut
5 ENVIRO‐SEAL bellows seal hex nut
6* Packing set, PTFE see following table
6* ENVIRO‐SEAL bellows seal packing set
PTFE for 9.5 mm (3/8 inch) stem (1 req'd
for single packing, 2 req'd for double
packing) 12A9016X012
6* ENVIRO‐SEAL bellows seal packing set (cont'd)
PTFE for NPS 2 with 12.7 mm (1/2 inch)
stem (2 req'd for double packing) 12A9016X012
PTFE for NPS 3 and 4 with 12.7 mm
(1/2 inch) stem (2 req'd for double
packing) 12A8832X012
7* Packing ring, PTFE composition see following table
7* ENVIRO‐SEAL bellows seal packing ring
for low chloride graphite ribbon/filament
packing arrangement
Ribbon packing ring for 9.5 mm (3/8 inch)
*Recommended spare parts
19
Page 20
ES Valve
July 2017
Instruction Manual
D100397X012
Key Description Part Number
and NPS 2 with 12.7 mm (1/2 inch) stem
(4 req'd) 18A0908X012
Filament packing ring for 9.5 mm
(3/8 inch) and NPS 2 with 12.7 mm
(1/2 inch) stem (4 req'd) 1P3905X0172
Ribbon packing ring for NPS 3 and 4
with 12.7 mm (1/2 inch) stem (4 req'd) 18A0918X012
Filament packing ring for NPS 3 and 4
with 12.7 mm (1/2 inch) stem (4 req'd) 14A0915X042
8 Spring
8 Lantern ring
8 ENVIRO‐SEAL bellows seal spring
8 ENVIRO‐SEAL bellows seal spacer
10 Special washer
11* Packing Box Ring
9.5 mm (3/8 inch) stem,
316 stainless steel 1J873135072
12.7 mm (1/2 inch) stem,
316 stainless steel 1J873235072
19.1 mm (3/4 inch) stem,
316 stainless steel 1J873335072
25.4 mm (1 inch) stem, 17‐4PH
stainless steel 1J873435072
31.8 mm (1‐1/4 inch) stem, 17‐4PH
stainless steel 1J873535072
12* Upper Wiper, felt
9.5 mm (3/8 inch) stem 1J872606332
12.7 mm (1/2 inch) stem 1J872706332
19.1 mm (3/4 inch) stem 1J872806332
25.4 mm (1 inch) stem 1J872906332
31.8 mm (1‐1/4 inch) stem 1J873006332
12* ENVIRO‐SEAL bellows seal upper wiper
For 9.5 mm (3/8 inch) and NPS 2 with 12.7 mm
(1/2 inch) stem 18A0868X012
For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem 18A0870X012
13* Packing Follower, 316 stainless steel
9.5 mm (3/8 inch) stem 1E943935072
12.7 mm (1/2 inch) stem 1E944335072
19.1 mm (3/4 inch) stem 1E944735072
25.4 mm (1 inch) stem 1H982335072
31.8 mm (1‐1/4 inch) stem 1H998435072
13* ENVIRO‐SEAL bellows seal bushing
For 9.5 mm (3/8 inch) stem (1 req'd),
for NPS 2 with 12.7 mm (1/2 inch) stem
(2 req'd)
S31600/PTFE 18A0820X012
R30006 18A0819X012
S31600/Cr Ct 11B1155X012
For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem (1 req'd)
S31600/PTFE 18A0824X012
R30006 18A0823X012
S31600/Cr Ct 11B1157X012
13* ENVIRO‐SEAL bellows seal bushing/liner
For 9.5 mm (3/8 inch) stem (1 req'd),
for NPS 2 with 12.7 mm (1/2 inch) stem
(2 req'd)
N10276 bushing, PTFE/glass liner 12B2713X012
N10276 bushing, PTFE/carbon liner 12B2713X042
Key Description Part Number
For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem (1 req'd)
N10276 bushing, PTFE/glass liner 12B2715X012
N10276 bushing, PTFE/carbon liner 12B2715X042
14 Pipe Plug for 1/4 NPT Tapping in Packing Box
14 Lubricator
14 Lubricator/Isolating Valve
15 Yoke Locknut
15 ENVIRO‐SEAL bellows seal Locknut
16 Pipe Plug for 1/2 NPT Tapped Extension Bonnets
16 ENVIRO‐SEAL bellows seal pipe plug
20* ENVIRO‐SEAL bellows seal stem/bellows assembly
1 Ply Bellows
S31600 trim mat'l, N06625 bellows mat'l
NPS 1 w/ 9.5 mm (3/8 inch) stem 32B4224X012
NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem 32B4225X012
NPS 2 w/ 12.7 mm (1/2 inch) stem 32B4226X012
NPS 3 w/ 12.7 mm (1/2 inch) stem 32B4227X012
NPS 4 w/ 12.7 mm (1/2 inch) stem 32B4228X012
N06022 trim mat'l, N06022 bellows mat'l
NPS 1 w/ 9.5 mm (3/8 inch) stem 32B4224X022
NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem 32B4225X022
NPS 2 w/ 12.7 mm (1/2 inch) stem 32B4226X022
NPS 3 w/ 12.7 mm (1/2 inch) stem 32B4227X022
NPS 4 w/ 12.7 mm (1/2 inch) stem 32B4228X022
2 Ply Bellows
S31600 trim mat'l, N06625 bellows mat'l
NPS 1 w/ 9.5 mm (3/8 inch) stem 32B4224X032
NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem 32B4225X032
NPS 2 w/ 12.7 mm (1/2 inch) stem 32B4226X032
NPS 3 w/ 12.7 mm (1/2 inch) stem 32B4227X032
NPS 4 w/ 12.7 mm (1/2 inch) stem 32B4228X032
N06022 trim mat'l, N06022 bellows mat'
NPS 1 w/ 9.5 mm (3/8 inch) stem 32B4224X042
NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem 32B4225X042
NPS 2 w/ 12.7 mm (1/2 inch) stem 32B4226X042
NPS 3 w/ 12.7 mm (1/2 inch) stem 32B4227X042
NPS 4 w/ 12.7 mm (1/2 inch) stem 32B4228X042
22* ENVIRO‐SEAL bellows seal bonnet gasket
(graphite/S31600)
NPS 1/2 through 1‐1/4 12B6316X022
NPS 1‐1/2 12B6317X022
NPS 2 12B6318X022
NPS 3 12B6319X022
NPS 4 12B6320X022
24 ENVIRO‐SEAL bellows seal adaptor
25 Cap Screw for 127 mm (5 inch) yoke boss
26 Hex Nut for 127 mm (5 inch) Yoke Boss
27 Pipe Nipple for Lubricator/Isolating Valve
28 ENVIRO‐SEAL bellows seal nameplate, warning
29 ENVIRO‐SEAL bellows seal drive screw
34 Lubricant, anti‐seize
36 ENVIRO‐SEAL bellows seal pin
37 ENVIRO‐SEAL bellows seal warning tag
38 ENVIRO‐SEAL bellows seal tie
39 ENVIRO‐SEAL bellows seal thrust ring
20
*Recommended spare parts
Page 21
Instruction Manual
D100397X012
Figure 8. Typical Bonnets
E0201
ES Valve
July 2017
30A9425‐A
DETAIL OF 5‐INCH (127 mm) YOKE
BOSS ACTUATOR BOLTING
PLAIN BONNET
CU3911‐D
STYLE 1 OR 2
EXTENSION BONNET
APPLY LUB
42B3947‐A
ENVIRO‐SEAL
BELLOWS SEAL BONNET
21
Page 22
ES Valve
(
July 2017
Instruction Manual
D100397X012
Figure 9. Typical HIGH‐SEAL Graphite ULF
Packing System
1. FIND NUMBER 219 NOT REQUIRED
WITH 3/8 INCH STEM
39B4153‐A
Figure 11. Typical ENVIRO‐SEAL Packing System with
Graphite ULF Packing
STUD
(KEY 200)
HEX NUT
(KEY 212)
PACKING
FLANGE
(KEY 201)
PACKING
RING
(KEY 209)
PACKING
RING
(KEY 210)
PACKING
BOX RING
KEY 211)
39B4612/A
SPRING
PACK
ASSEMBLY
(KEY 217)
GUIDE
BUSHING
(KEY 207)
PACKING
WASHERS
(KEY 214)
GUIDE
BUSHING
(KEY 208)
Figure 10. Typical ENVIRO‐SEAL Packing System with
PTFE Packing
A6297‐1
Figure 12. Typical ENVIRO‐SEAL Packing System with
Duplex Packing
200
212
201
215
216
207
209
211
A6722
213
217
207
207
214
207
22
Page 23
Instruction Manual
D100397X012
ES Valve
July 2017
Keys 6*, 7*, 8, and 10 Packing Box Parts
DESCRIPTION
Packing Set, PTFE (1 req'd for
single, 2 req'd for double)
Spring, Stainless Steel (for single only) 8 1F125437012 1F125537012 1F125637012 1D582937012 1D387437012
PTFE
V‐Ring Packing
PTFE/Composition
Packing
Graphite
Ribbon/
Filament
1. For ENVIRO‐SEAL or HIGH‐SEAL packing box parts, see instruction manual ENVIRO‐SEAL Packing System for Sliding‐Stem Valves, D101642X012 or HIGH‐SEAL Live‐Loaded Packing System,
D101453X012.
2. Key 6 for double construction contains one extra Packing Ring for the 9.5 mm (3/8 inch) stem and one extra Lower Wiper for all sizes. Discard upon assembly.
Lantern Ring, Stainless Steel
(for double only)
Quantity required Double ‐ ‐ ‐ 1 2 1 1 1
Special Washer, Stainless Steel
(for single only)
Packing Ring, PTFE composition 7 1F3370X0012 1E319001042 1E319101042 1D7518X0012 1D7520X0012
Quantity required Double ‐ ‐ ‐ 7 10 8 8 8
Lantern Ring, Stainless Steel (1 req'd) 8 1F364135072 1J962335072 0N028435072 0U099735072 0W087135072
Graphite Ribbon Ring 7 1V3160X0022 1V3802X0022 1V2396X0022 1U6768X0022 1V5666X0022
Quantity required
Graphite Filament Ring 7 1F3370X0322 1E3190X0222 1E3191X0282 1D7518X0132 1D7520X0162
Quantity required
Lantern Ring 8 1F364135072 1J962335072 0N028435072 0U099735072 0W087135072
Quantity required
Valve Body (figures 13‐15)
Key Description Part Number
1 Valve Body
If you need a valve body as a replacement part, order by valve
size, serial number, and desired material.
2* Valve plug see following table
3* Cage see following table
4 Trim adaptor
5 Trim adaptor
7* Valve plug stem see following table
8* Pin, 316 stainless steel
9.5 mm (3/8 inch) stem 1B599135072
12.7 mm (1/2 inch) stem 1B599635072
19.1 mm (3/4 inch) stem 1F723635072
25.4 mm (1 inch) or 31.8 mm (1‐1/4 inch)
stem 1D269735072
9* Liner see following table
9* Seat Ring see following table
10* Bonnet Gasket see following table
11* Cage Gasket see following table
12* Spiral‐Wound Gasket see following table
13* Seat Ring or Liner Gasket see following table
14* Adaptor Gasket see following table
15 Cap Screw
15 Stud
16 Nut
17 Pipe Plug
18 Flow Direction Arrow
19 Drive Screw
(1)
KEY
NO.
9.5 (3/8) 12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.8 (1‐1/4)
(2)
Single ‐ ‐ ‐ 2 2 2 2 2
Double ‐ ‐ ‐ 3 3 3 3 3
Single ‐ ‐ ‐ 2 2 3 3 3
Double ‐ ‐ ‐ 4 4 5 5 5
Single ‐ ‐ ‐ 2 3 2 2 2
Double ‐ ‐ ‐ 1 2 1 1 1
6 1R290001012 1R290201012 1R290401012 1R290601012 1R290801012
8 1F364135072 1J962335072 0N028435072 0U099735072 0W087135072
10 1F125236042 1F125136042 1F125036042 1H982236042 1H995936042
STEM DIAMETER, INCHES (mm)
Key Description Part Number
22* Disk Seat see following table
23* Disk see following table
26 Load Ring
27* Shim see following table
31* Whisper Trim III Cage Retainer for
Levels A3, B3 & C3 (NPS 6 ES only)
13Cr 400‐Series SST 22A3255X012
WCC steel (ENC) 22A3256X012
316 stainless steel (ENC) 22A3256X022
316 stainless steel w/CoCr‐A bore 22A3257X012
316 stainless steel (electrolized) 31A9792X012
31* Whisper Trim III Cage retainer & Baffle
Ass'y for Level D3 (NPS 6 ES only)
13Cr 400‐Series SST retainer & steel
baffle 22A3258X012
WCC steel (ENC) retainer & steel
baffle 22A3258X022
316 stainless steel (ENC) retainer &
steel baffle 22A3258X052
316 stainless steel w/CoCr‐A bore
retainer & steel baffle 22A3258X032
316 stainless steel (ENC) retainer &
316 stainless steel baffle 22A3258X042
316 stainless steel (electrolized)
retainer & 316 stainless steel baffle 22A3258X062
32 Whisper Trim III Bonnet Spacer
51* Shim see following table
53 Nameplate
54 Wire
20* Adaptor Gasket see following table
21* Seat Disk Retainer see following table
*Recommended spare parts
23
Page 24
ES Valve
July 2017
Figure 13. NPS 1/2 through 6 Fisher ES and EAS Valves
STD TRIM
WHISPER TRIM
Instruction Manual
D100397X012
FLOW DIRECTION
CAVITROL TRIM
30A9543‐D
FLOW DIRECTION
STD TRIM
CAVITROL TRIM
DETAIL OF
COMPOSITION
(PTFE) SEAT
CU9974‐E
24
Page 25
Instruction Manual
D100397X012
ES Valve
July 2017
Figure 14. NPS 8 Fisher ES Valve with Optional Drain Plug
FLOW DIRECTION
CAVITROL TRIM
STD TRIM
WHISPER TRIM
40A3288‐C
B1884‐1
METAL SEAT
COMPOSITION (PTFE) SEAT
25
Page 26
ES Valve
July 2017
Figure 15. Whisper Trim III Cage Detail with Optional Drain Plug
Instruction Manual
D100397X012
E1137
52A3326‐D
26
Page 27
Instruction Manual
D100397X012
Figure 16. Fisher ES Valve Assembly with WhisperFlo Cage with Optional Drain Plug
ES Valve
July 2017
19
16
7
32
10
12
8
9
18
15
10
31
53
3
13
1
17
E1138
2
27
Page 28
ES Valve
July 2017
Instruction Manual
D100397X012
Keys 2*, 7*, and 8* Valve Plug and Stem Assembly for Plain Bonnet
VALVE SIZE,
NPS
ORIFICE SIZE
ES EAS mm Inch
6.4 0.25
9.5 0.375
1/2 thru 2 1, 2
12.7 0.5
19.1 0.75
25.4 1
6.4 0.25
9.5 0.375
1/2 thru 2 1, 2
12.7 0.5
19.1 0.75
25.4 1
1/2, 3/4,
1, 1‐1/4
1 33.3
1.312
1‐1/2 2 47.6 1.875
1‐1/2 x 1 2 x 1 33.3
2, 3 x 2 4 x 2 58.7
2 x 1 ‐ ‐ ‐ 33.3
2‐1/2,
4 x 2‐1/23,6 x 2‐1/2
1.312
2.312
1.312
73.0 2.875
2‐1/2 x 1‐1/2 3 x 1‐1/2 47.6 1.875
3 4 87.3
3.437
4 6 111.1 4.375
6 ‐ ‐ ‐ 177.8 7
8 ‐ ‐ ‐ 203.2 8
1. Not for use with 17‐4PH stainless steel cages above 210_C (410_F) or CoCr‐A cages above 427_C (800_F); use high temperature valve plugs for these applications.
2. For use with 17‐4PH stainless steel cages between 210_C (410_F) and 427_C (800_F) and with CoCr‐A cages over 427_C (800_F), note that the letter H is stamped on top for identification.
STEM DIA
& VSC
SIZE
mm
9.5
9.5
9.5
9.5
9.5
12.7
12.7
12.7
12.7
12.7
9.5
12.7
5
9.5
12.7
9.5
12.7
5
12.7
19.1
5
12.7
5
12.7
19.1
12.7
12.7
19.1
5
12.7
19.1
19.1
19.1
13Cr 400‐Series
Stainless Steel
316 Stainless
(1)
Steel
Inch
3/8 1U2885X0072 1U2885X0042 2U8549X0032 2V3640X0032 21A8444X022
3/8 1U2886X0022 1U2886X0032 2U8550X0032 2V5702X00A2 21A8445X022
3/8 1U2887X0052 1U2887X0062 2U8551X0052 2V5681X0052 21A8446X042
3/8 1U2888X0042 1U2888X0072 2U8552X0012 2V3335X0042 21A8447X022
3/8 1U2889X0072 1U2889X0102 2U8553X00F2 2V5468X0042 ‐ ‐ ‐
1/2 1U2885X0092 1U2885X0222 2U8549X0022 2V3640X0092 ‐ ‐ ‐
1/2 1U2886X0262 1U2886X0232 2U8550X0062 2V5702X0032 ‐ ‐ ‐
1/2 1U2887X0042 1U2887X0032 2U8551X0042 2V5681X0032 21A8446X032
1/2 1U2888X0082 1U2888X0092 2U8552X0032 2V3335X0052 ‐ ‐ ‐
1/2 1U2889X0062 1U2889X0052 2U8553X00G2 2V5468X0032 21A8448X022
3/8
1/2
3/8
1/2
3/8
1/2
1/2
3/4
1U2161X0082
1U2161X0232
11A5206X042
11A5207X052
1U2161X0122
1U2162X0082
11A5214X102
11A5215X072
1U2161X0132
1U2161X0192
11A5206X052
11A5207X242
1U2161X0182
‐ ‐ ‐
11A5214X122
11A5215X082
1/2 1U2162X0022 1U2162X0052 11A5201X062 11A5203X062 11A5205X032
1/2
3/4
11A5222X042
11A5223X052
11A5222X112
11A5223X112
1/2 11A5207X052 11A5207X242 11A5209X022 11A5211X062 11A5213X022
1/2
3/4
1/2
3/4
11A5230X082
11A5231X052
11A5238X052
11A5239X072
11A5230X092
11A5231X042
11A5238X072
11A5239X062
3/4 11A5250X052 11A5250X142 11A5253X022 ‐ ‐ ‐ ‐ ‐ ‐
3/4 21A5262X0A2 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
316 Stainless
Steel w/ CoCr‐A
on Seat
(1)
11A5200X032
‐ ‐ ‐
11A5208X022
11A5209X022
‐ ‐ ‐
‐ ‐ ‐
11A5216X062
‐ ‐ ‐
11A5224X022
‐ ‐ ‐
11A5232X022
‐ ‐ ‐
11A5241X022
‐ ‐ ‐
316 Stainless
Steel w/ CoCr‐A
on Seat & Guide
11A5202X032
11A5202X052
11A5210X032
11A5211X062
11A5202X062
11A5203X042
11A5218X042
11A5219X072
11A5226X072
11A5227X052
11A5234X042
11A5235X042
11A5244X032
11A5245X112
(1)
HIGH
TEMPERATURE
316 Stainless
Steel w/ CoCr‐A
on Seat & Guide
11A5204X042
‐ ‐ ‐
‐ ‐ ‐
11A5213X022
11A5204X032
11A5205X052
11A5220X042
11A5221X052
‐ ‐ ‐
11A5229X032
11A5236X042
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
(2)
28
*Recommended spare parts
Page 29
Instruction Manual
D100397X012
ES Valve
July 2017
Keys 2*, 7*, and 8* Valve Plug and Stem Assembly for Style 1 Extension Bonnet
VALVE SIZE,
NPS
ES EAS mm Inch mm Inch
1/2 thru 2 1, 2
1/2 thru 2 1, 2
1/2, 3/4,
1, 1‐1/4
1‐1/2 2 47.6 1.875
1‐1/2 x 1 2 x 1 33.3 1.3125
2, 3 x 2 4 x 2 58.7 2.3125
2 x 1 ‐ ‐ ‐ 33.3 1.3125 12.7 1/2 1U2162X0042 1U2162X0032 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
2‐1/2,
4 x 2‐1/2
2‐1/2 x 1‐1/2 3 x 1‐1/2 47.6 1.875 12.7 1/2 11A5207X062 ‐ ‐ ‐ ‐ ‐ ‐ 11A5211X052 ‐ ‐ ‐
3 4 87.3 3.4375
4 6 111.1 4.375
6 ‐ ‐ ‐ 177.8 7 19.1 3/4 11A5250X072 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
8 ‐ ‐ ‐ 203.2 8 19.1 3/4 ‐ ‐ ‐ ‐ ‐ ‐ 21A5265X022 ‐ ‐ ‐ ‐ ‐ ‐
1. Not for use with 17‐4PH stainless steel cages above 210_C (410_F) or CoCr‐A cages above 427_C (800_F); use high temperature valve plugs for these applications.
2. For use with 17‐4PH stainless steel cages between 210_C (410_F) and 427_C (800_F) and with CoCr‐A cages over 427_C (800_F), note that the letter H is stamped on top for identification.
1 33.3 1.3125
3,
6 x 2‐1/2
ORIFICE SIZE
6.4 0.25 9.5 3/8 1U2885X0082 ‐ ‐ ‐ 2U8549X0042 2V3640X0042 ‐ ‐ ‐
9.5 0.375 9.5 3/8 1U2886X0072 1U2886X0042 2U8550X0042 2V5702X0042 21A8445X032
12.7 0.5 9.5 3/8 1U2887X0092 1U2887X0232 2U8551X0032 2V5681X0062 ‐ ‐ ‐
19.1 0.75 9.5 3/8 1U2888X0062 1U2888X0112 2U8552X0022 ‐ ‐ ‐ 21A8447X0B2
25.4 1 9.5 3/8 1U2889X0082 1U2889X0112 ‐ ‐ ‐ 2V5468X0242 21A8448X032
6.4 0.25 12.7 1/2 1U2885X0112 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
9.5 0.375 12.7 1/2 ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐ ‐
12.7 0.5 12.7 1/2 1U2887X0122 ‐ ‐ ‐ 2U8551X0062 ‐ ‐ ‐ ‐ ‐ ‐
19.1 0.75 12.7 1/2 1U2888X0122 ‐ ‐ ‐ 2U8552X0052 2V3335X0122 ‐ ‐ ‐
25.4 1 12.7 1/2 1U2889X0162 ‐ ‐ ‐ 2U8553X00C2 2V5468X00C2 ‐ ‐ ‐
73.0 2.875
STEM DIA
& VSC
SIZE
9.5
12.7
9.5
12.7
9.5
12.7
12.7
19.1
12.7
19.1
12.7
19.1
12.7
19.1
3/8
1/2
3/8
1/2
3/8
1/2
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
13Cr 400‐Series
Stainless Steel
1U2161X0162
‐ ‐ ‐
11A5206X062
11A5207X062
1U2161X0212
1U2162X0242
11A5214X112
11A5215X062
11A5222X062
11A5223X072
11A5230X482
11A5231X152
11A5238X102
11A5239X192
316 Stainless
(1)
Steel
1U2161X0262
‐ ‐ ‐
11A5206X292
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
11A5238X062
‐ ‐ ‐
316 Stainless
Steel w/ CoCr‐A
(1)
on Seat
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
11A5216X032
‐ ‐ ‐
‐ ‐ ‐
11A5225X022
‐ ‐ ‐
11A5233X022
‐ ‐ ‐
‐ ‐ ‐
316 Stainless
Steel w/ CoCr‐A
on Seat &
(1)
Guide
11A5202X082
‐ ‐ ‐
11A5210X052
11A5211X052
11A5202X152
‐ ‐ ‐
11A5218X052
11A5219X042
11A5226X032
‐ ‐ ‐
11A5234X052
‐ ‐ ‐
‐ ‐ ‐
11A5245X122
HIGH
TEMPERATURE
316 Stainless
Steel w/ CoCr‐A
on Seat & Guide
11A5204X112
11A5205X152
11A5212X022
‐ ‐ ‐
11A5204X052
11A5205X072
11A5220X032
11A5221X042
‐ ‐ ‐
11A5229X022
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
(2)
*Recommended spare parts
29
Page 30
ES Valve
July 2017
Instruction Manual
D100397X012
Keys 2* Valve Plug
VALVE SIZE,
NPS
ES EAS mm Inch mm Inch
1/2 thru 2 1, 2
1/2, 3/4,
1, 1‐1/4,
1‐1/2 X 1
1‐1/2 2 47.6 1.875
2, 3 x 2 4 x 2 58.7 2.3125
2 x 1 ‐ ‐ ‐ 33.3 1.3125 12.7 1/2 1U216246172 1U216235072 11A5201X012 11A5203X012 11A5205X012
2‐1/2,
4 x 2‐1/2
2‐1/2 x 1‐1/2 3 x 1‐1/2 47.6 1.875 12.7 1/2 11A5207X012 11A5207X022 11A5209X012 11A5211X012 11A5213X012
3 4 87.3 3.4375
4 6 111.1 4.375
6 ‐ ‐ ‐ 177.8 7
8 ‐ ‐ ‐ 203.2 8
1. Not for use with 17‐4PH stainless steel cages above 210_C (410_F) or CoCr‐A cages above 427_C (800_F); use high temperature valve plugs for these applications.
2. For use with 17‐4PH stainless steel cages between 210_C (410_F) and 427_C (800_F) and with CoCr‐A cages over 427_C (800_F), note that the letter H is stamped on top for identification.
1, 2 X 1 33.3 1.3125
3,
6 x 2‐1/2
ORIFICE SIZE
6.4 0.25 9.5 3/8 1U288546172 1U288535072 2U854946052 2V364046062 21A8444X012
9.5 0.375 9.5 3/8 1U288646172 1U288635072 2U855046052 2V570246062 21A8445X012
12.7 0.5 9.5 3/8 1U288746172 1U288735072 2U855146052 2V568146062 21A8446X012
19.1 0.75 9.5 3/8 1U288846172 1U288835072 2U855246052 2V333546062 21A8447X012
25.4 1 9.5 3/8 1U288946172 1U288935072 2U855346052 2V546846062 21A8448X012
73.0 2.875
STEM DIA
& VSC
SIZE
9.5
12.7
9.5
12.7
12.7
19.1
12.7
19.1
12.7
19.1
12.7
19.1
25.4
19.1
25.4
31.8
19.1
25.4
31.8
3/8
1/2
3/8
1/2
1/2
3/4
1/2
3/4
1/2
3/4
1/2
3/4
1
3/4
1
1‐1/4
3/4
1
1‐1/4
13Cr
400‐Series
Stainless Steel
1U216146172
1U216246172
11A5206X012
11A5207X012
11A5214X012
11A5215X012
11A5222X012
11A5223X012
11A5230X012
11A5231X012
11A5238X012
11A5239X012
11A5240X012
11A5250X012
11A5251X012
11A5252X012
21A5262X012
21A5263X012
21A5264X012
316 Stainless
(1)
Steel
1U216135072
1U216235072
11A5206X022
11A5207X022
11A5214X022
11A5215X022
11A5222X022
11A5223X022
11A5230X022
11A5231X022
11A5238X022
11A5239X022
11A5240X022
11A5250X022
11A5251X022
11A5252X022
21A5262X022
21A5263X022
21A5264X022
316 Stainless
Steel w/ CoCr‐A
on Seat
11A5200X012
11A5201X012
11A5208X012
11A5209X012
11A5216X012
11A5217X012
11A5224X012
11A5225X012
11A5232X012
11A5233X012
11A5241X012
11A5242X012
11A5243X012
11A5253X012
11A5254X012
11A5255X012
21A5265X012
21A5266X012
21A5267X012
(1)
316 Stainless
Steel w/
CoCr‐A
on Seat &
(1)
Guide
11A5202X012
11A5203X012
11A5210X012
11A5211X012
11A5218X012
11A5219X012
11A5226X012
11A5227X012
11A5234X012
11A5235X012
11A5244X012
11A5245X012
11A5246X012
11A5256X012
11A5257X012
11A5258X012
21A5268X012
21A5269X012
21A5270X012
HIGH
TEMPERATURE
316 Stainless
Steel w/ CoCr‐A
on Seat & Guide
11A5204X012
11A5205X012
11A5212X012
11A5213X012
11A5220X012
11A5221X012
11A5228X012
11A5229X012
11A5236X012
11A5237X012
11A5247X012
11A5248X012
11A5249X012
11A5259X012
11A5260X012
11A5261X012
21A5271X012
21A5272X012
21A5273X012
(2)
Key 3* Quick Opening Cage
VALVE SIZE, NPS
ES EAS
1, 1‐1/4, 1‐1/2 x 1, or 2 x 1
1‐1/2 or 2‐1/2 x 1‐1/2
2 or 3 x 2
2‐1/2 or 4 x 2‐1/2
3
4
6
8
30
1 or 2 x 1
2 or 3 x 1‐1/2
4 x 2
3 or 6 x 2‐1/2
4
6
‐ ‐ ‐
‐ ‐ ‐
17‐4PH
SST
(HARDENED)
2U215033272
2U219233272
2U223433272
2U227633272
2U231833272
2U236033272
2U506333272
20A3249X012
316 SST
Chrome
Plated
2U691146102
2U691846102
2U692146102
2U692446102
2U692746102
2U693046102
2U693546102
20A4350X012
*Recommended spare parts
Nickel
Coated
2U740348932
2U725448932
2U740448932
2U740548932
2U740648932
2U740748932
2U806948932
20A5469X012
ALLOY 6
2U215039102
2U219239102
2U223439102
2U227639102
2U231839102
2U236039102
2U506339102
20A3249X092
Page 31
Instruction Manual
D100397X012
Key 3* Linear Cage
VALVE SIZE, NPS
ES EAS
1, 1‐1/4, 1‐1/2 x 1, or 2 x 1
1‐1/2 or 2‐1/2 x 1‐1/2
2 or 3 x 2
2‐1/2 or 4 x 2‐1/2
3
4
6
8
Key 3* Equal Percentage Cage
VALVE SIZE, NPS
ES EAS
1, 1‐1/4, 1‐1/2 x 1, or 2 x 1
1‐1/2 or 2‐1/2 x 1‐1/2
2 or 3 x 2
2‐1/2 or 4 x 2‐1/2
3
4
6
8
1 or 2 x 1
2 or 3 x 1‐1/2
4 x 2
3 or 6 x 2‐1/2
4
6
‐ ‐ ‐
‐ ‐ ‐
1 or 2 x 1
2 or 3 x 1‐1/2
4 x 2
3 or 6 x 2‐1/2
4
6
‐ ‐ ‐
‐ ‐ ‐
17‐4PH
SST
(HARDENED)
2U215633272
2U219833272
2U224033272
2U228233272
2U232433272
2U236633272
2U506133272
20A3247X012
17‐4PH
SST
(HARDENED)
2U215333272
2U219533272
2U223733272
2U227933272
2U232133272
2U236333272
2U505933272
20A3245X012
Chrome
Plated
2U691746102
2U692046102
2U692346102
2U692646102
2U692946102
2U693346102
2U693846102
20A4349X012
Chrome
Plated
2U691346102
2U691946102
2U692246102
2U692546102
2U692846102
2U693146102
2U693746102
20A4348X012
316 SST
316 SST
Nickel
Coated
2U741448932
2U741548932
2U741648932
2U741748932
2U741848932
2U741948932
2U806848932
20A5468X012
Nickel
Coated
2U740848932
2U740948932
2U741048932
2U741148932
2U741248932
2U741348932
2U806748932
20A5467X012
ES Valve
July 2017
ALLOY 6
2U215639102
2U219839102
2U224039102
2U228239102
2U232439102
2U236639102
2U506139102
20A3247X092
ALLOY 6
2U215339102
2U219539102
2U223739102
2U227939102
2U232139102
2U236339102
2U505939102
20A3245X092
Key 3* Micro‐Flow and Micro‐Flute Cage
ES
VALVE SIZE,
NPS
1/2, 3/4, 1, 1‐1/4
1‐1/2
2
VALVE SIZE,
1, 2 x 1
2
‐ ‐ ‐
EAS
NPS
17‐4PH SST
(HARDENED)
2U215033272
1U286733272
1U286933272
Key 3* Whisper Trim I Cage
VALVE SIZE, NPS
ES EAS
1, 1‐1/4, 1‐1/2 x 1, or 2 x 1
1‐1/2 or 2‐1/2 x 1‐1/2
2 or 3 x 2
2‐1/2 or 4 x 2‐1/2
3
4
6
1 or 2 x 1
2 or 3 x 1‐1/2
4 x 2
3 or 6 x 2‐1/2
4
6
‐ ‐ ‐
Key 3* Whisper Trim III Cage (NPS 6 Fisher ES Only)
Level 13Cr 400‐Series Stainless Steel
A3
B3
C3
D3
32A3248X012
32A3249X012
32A3250X012
32A6217X012
Chrome
Plated
2U691146102
2U693946102
2U694046102
316 SST
(Nickel Coated)
32A3251X012
32A3252X012
32A3253X012
32A6220X012
316 SST
Nickel
Coated
2U740348932
2U742048932
2U742148932
WHISPER TRIM I,
17‐4PH SST (HARDENED)
ALLOY
2U215039102
1U286739102
1U286939102
2V502333272
2V502433272
2V502533272
2V502633272
2V502733272
23A8915X032
23A8913X012
316 SST
(Electrolized)
32A3336X012
32A3337X012
32A3338X012
32A6741X012
*Recommended spare parts
31
Page 32
ES Valve
July 2017
Instruction Manual
D100397X012
Key 7* Fisher ES Valve Plug Stem, 316 stainless steel (not for Whisper Trim III cage)
STEM
VALVE
SIZE, NPS
1/2, 3/4,
1, 1‐1/4,
or 1‐1/2
2
2‐1/2 or 3
Full
Capacity
Restricted
Capacity
1. 667 actuator.
2. 657 or 585C Size 60‐130 actuator.
3. For the NPS 8 valve, the plain bonnet is standard for cast iron and WCC valves, and the style 1 bonnet is standard for CF8M valves.
4
6
(3)
8
1‐1/2 x 1
2 x 1 or
2‐1/2 x 1‐1/2
3 x 2
4 x 2‐1/2
DIA &
VSC SIZE
mm Inches mm Inches mm Inches mm Inches
9.5
9.5
3/8
1/2
1/2
3/4
1/2
3/4
1/2
3/4
(1)
(1)
1
(2)
(2)
1
3/4
1
1‐1/4
3/4
1
1‐1/4
3/8
1/2
1/2
3/4
1/2
3/4
12.7
12.7
19.1
12.7
19.1
12.7
19.1
25.4
25.4
19.1
25.4
31.8
19.1
25.4
31.8
12.7
12.7 1/2 300 11.8125 1U389035162 402 15.8125 1U217935162 605 23.8125 1U389335162
12.7
19.1
12.7
19.1
PLAIN BONNET
Stem Length
225
8.875
300
11.8125
311
12.25
372
14.625
321
12.625151U230535162
381
321
12.625
394
464
489
403
499
508
492
614
705
241
311
311
372
321
381
15.5
18.25
19.25
15.875
19.625
20
19.375
24.1875
27.4375
9.375
12.25
12.25
14.625
12.625151U230535162
(3)
Part
Number
1U388835162
1U389035162
1K586935162
1U226535162
1U230835162
1U230535162
1K587735162
1K759035162
1U217535162
1L996435162
1N704735162
1K415435162
1K588035162
1K7891X0012
1L268835162
1U223635162
1K586935162
1K586935162
1U226535162
1U230835162
Style 1
Stem Length
311
12.25
402
15.8125
413
16.25191U226335162
483
421
16.5625
502
19.75
421
16.5625
502
19.75
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
511
20.125
630
24.8125
656
25.8125
533
614
705
324
413
413
483
421
502
21
24.8125
29.4375
12.75
16.25
16.25191U226335162
16.5625
19.75
(3)
1U217735162
1U217935162
1L400135162
1U230635162
1U444635162
1U230635162
1U444635162
1U507135162
1K785135162
1R562435162
1U928235162
1K7891X0012
1L268835162
1U227035162
1U226335162
1L400135162
1U230635162
1U444635162
EXTENSION BONNET
Part
Number
405
473
614
624
624
694
‐ ‐ ‐
‐ ‐ ‐
699
418
486
614
624
681
Stem Length
15.9375
18.625
24.1875
‐ ‐ ‐
24.5625
‐ ‐ ‐
24.5625
27.3125
‐ ‐ ‐
‐ ‐ ‐
27.5
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
16.4375
19.125
24.1875
‐ ‐ ‐
24.5625
26.8125
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
Style 2
Part
Number
10A8823X022
1U218035162
1U226435162
‐ ‐ ‐
1U230735162
‐ ‐ ‐
1U230735162
1U240035162
‐ ‐ ‐
‐ ‐ ‐
1U524435162
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
1U227235162
1U227335162
1U226435162
‐ ‐ ‐
1U230735162
1U232335162
Key 7* Whisper Trim III Valve Plug Stem, 316 stainless steel (NPS 6 Fisher ES only)
STEM DIA. & VSC SIZE
mm Inches Style 1 Style 2
PLAIN BONNET
19.1 3/4 1U341635162 1U928235162 1U6276X0012
25.4 1 1P847635162 1U627735162 ‐ ‐ ‐
EXTENSION BONNET
32
*Recommended spare parts
Page 33
Instruction Manual
D100397X012
Key 7* Fisher EAS Valve Plug Stem for Plain and Extension Bonnets
PLAIN BONNET EXTENSION BONNET
Stem Length
8.875
11.8125
12.625151U230535162
12.625
15.5
18.25
19.25
9.375
12.25
12.25
14.625
12.625151U230535162
Part
Number
1U388835162
1U389035162
1U230835162
1U230535162
1K587735162
1K759035162
1U217535162
1U223635162
1K586935162
1K586935162
1U226535162
1U230835162
VALVE
SIZE, NPS
1 or 2
Full
Capacity
Restricted
Capacity
1. 667 actuator.
2. 657 or 585C Size 60‐130 actuator.
3 or 4
6
2 x 1
3 x 1‐1/2 12.7 1/2 300 11.8125 1U389035162 402 15.8125 1U217935162 605 23.8125 1U389335162
4 x 2
6 x 2‐1/2
STEM
DIA &
VSC SIZE
mm Inches mm Inches mm Inches mm Inches
9.5
3/8
12.7
12.7
19.1
12.7
19.1
25.4
25.4
9.5
12.7
12.7
19.1
12.7
19.1
(1)
(2)
1/2
1/2
3/4
1/2
3/4
1
1
3/8
1/2
1/2
3/4
1/2
3/4
225
300
321
381
321
394
(1)
464
(2)
489
241
311
311
372
321
381
Style 1 Style 2
Stem Length
311
12.25
402
15.8125
421
16.5625
502
19.75
421
16.5625
502
19.75
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
324
12.75
413
16.25
413
16.25191U226335162
483
421
16.5625
502
19.75
Part
Number
1U217735162
1U217935162
1U230635162
1U444635162
1U230635162
1U444635162
‐ ‐ ‐
‐ ‐ ‐
1U227035162
1U226335162
1L400135162
1U230635162
1U444635162
Stem Length
405
15.9375
473
18.625
624
24.5625
‐ ‐ ‐
624
24.5625
694
27.3125
‐ ‐ ‐
‐ ‐ ‐
418
16.4375
486
19.125
614
24.1875
‐ ‐ ‐
624
24.5625
681
26.8125
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
ES Valve
July 2017
Part
Number
1U217835162
1U218035162
1U230735162
‐ ‐ ‐
1U230735162
1U240035162
‐ ‐ ‐
‐ ‐ ‐
1U227235162
1U227335162
1U226435162
‐ ‐ ‐
1U230735162
1U232335162
Key 7* Valve Plug Stem for Bellows Seal Bonnet, 316 stainless steel
VALVE SIZE, NPS STEM DIA. & VSC SIZE STEM LENGTH
ES EAS mm Inches mm Inches
1/2, 3/4, 1, 1‐1/4, 1‐1/2, or 1‐1/2 x 1 1, 2, or 2 x 1
9.5
12.7
3/8
1/2
222
286
8.75
11.25
2, 2‐1/2, 2‐1/2 x 1‐1/2, or 3 3 or 4 12.7 1/2 314 12.375 1U389235162
‐ ‐ ‐ 3 x 1‐1/2 12.7 1/2 295 11.625 1U388935162
2 x 1 or 3 x 2 4 x 2 12.7 1/2 305 12 1U389135162
4 6
4 x 2‐1/2 6 x 2‐1/2
12.7
19.1
12.7
19.1
1/2
3/4
1/2
3/4
327
387
327
375
12.875
15.25
12.875
14.75
6 ‐ ‐ ‐ 19.1 3/4 387 15.25 1K587635162
PART NUMBER
1R288535162
1R288835162
2R369335162
1K587635162
2R369335072
1U389435162
Key 9* Metal‐Seat Seat Ring (not for Whisper Trim III Cage)
VALVE SIZE, NPS
ES EAS
1, 1‐1/4 or 2 x 1 1 1U222546172 1U222535072 1U222539102
1‐1/2 x 1 2 x 1 1U222046172 1U222035072 1U222039102
1‐1/2 or 2‐1/2 x 1‐1/2 2 or 3 x 1‐1/2 1U221946172 1U221935072 1U221939102
2 or 3 x 2 4 x 2 1U222646172 1U222635072 1U222639102
2‐1/2 or 4 x 2‐1/2 3 or 6 x 2‐1/2 1U222746172 1U222735072 1U222739102
3
4
6
4
6
‐ ‐ ‐
8 ‐ ‐ ‐ 20A3260X012 20A3260X022 20A3260X152
13Cr 400‐Series Stainless
Steel
1U222846172
1U222946172
1U508046172
316 SST R30006
1U222835072
1U222933092
1U508033092
1U222839102
1U222939102
1U508039102
*Recommended spare parts
33
Page 34
ES Valve
July 2017
Key 9* Fisher EAS Liner
Liner
Material
416
SST
(hardened)
316
SST
Valve
Size, NPS
2 x 1
3 x 1‐1/2
4 x 2
6 x 2‐1/2
2 x 1
3 x 1‐1/2
4 x 2
6 x 2‐1/2
Instruction Manual
D100397X012
CL150
Raised Face
1
2
3
4
6
1
2
3
4
6
1V560146172
1V560346172
1V560646172
2V561346172
2V560946172
2V562246172
2V561846172
2V563146172
2V562646172
1V560135072
1V560335072
1V560535072
2V561335072
2V560935072
2V562235072
2V561835072
2V563135072
2V562635072
CL300
Raised Face
1U384246172
1U384346172
1U385146172
2U384546172
2U385346172
2U384746172
2U385546172
2U384946172
2U385746172
1U384235072
1U384335072
1U385135072
2U384535072
2U385335072
2U384735072
2U385535072
2U384935072
2U385735072
CL600
Raised Face
1V560246172
1V560546172
1V387646172
2V561646172
2V545946172
2V561946172
2V561246172
2V562846172
2V562346172
1V560235072
1V560535072
1V387635072
2V561635072
2V545935072
2V561935072
2V561235072
2V562835072
2V562335072
Socket
Weld
1V560146172
1V560346172
1V560646172
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
1V560135072
1V560335072
1V560635072
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
‐ ‐ ‐
Schedule
40 or 80
Butt Weld
1V560146172
1V560346172
1V560646172
2V561346172
2V560946172
2V562246172
2V561846172
2U384946172
2U385746172
1V560135072
1V560335072
1V560635072
2V561335072
2V560935072
2V562235072
2V561835072
2U384935072
2U385735072
Key 9* Whisper Trim III Seat Ring (NPS 6 Fisher ES only)
13Cr 400‐Series Stainless Steel 316 SST 316 SST w/CoCr‐A
21A9794X012 21A9794X022 21A9795X012
Key 9* Seat Ring, Micro‐Flow and Micro‐Flute Cage
ORIFICE SIZE,
INCHES
0.1875
0.25
0.375
0.5
0.75
1
0.1875
0.25
0.375
0.5
0.75
1
0.1875
0.25
0.375
0.5
0.75
1
1. Micro‐Flow cage only.
ES—1/2, 3/4, 1, 1‐1/4 ES—1‐1/2, EAS—2 ES—2
(1)
(1)
(1)
1V108346172
1U285246172
1U285346172
1U285446172
1U2855X0342
1U2856X0242
1V108335072
13A5872X012
13A5873X012
1U285435072
1U2855X0332
1U2856X0232
2V626250332
2U855946052
2U856046052
2U856146052
2U8562X0192
2U8563X0092
13Cr 400‐Series Stainless Steel
316 SST
316 SST with CoCr‐A Seat
VALVE SIZE, NPS
1V108446172
1U285746172
1U285846172
1U285946172
1U286046172
1U286146172
1V108435072
1U285735072
1U285835072
1U285935072
1U286035072
1U286135072
20A0140X012
2U856446052
2U856546052
2U856646052
2U856746052
2U856846052
1V108546172
1U286246172
1U286346172
1U286446172
1U286546172
1U286646172
1V108535072
1U286235072
1U286335072
1U286435072
1U286535072
1U286635072
20A0141X012
2U856946052
2U857046052
2U857146052
2U857246052
2U857346052
34
*Recommended spare parts
Page 35
Instruction Manual
D100397X012
Gasket Descriptions
KEY NUMBER DESCRIPTION
-198_ to 593_C (-325_ to 1100_F)
10 Bonnet Gasket
11 Cage Gasket
13 Seat Ring or Liner Gasket
14 or 20 Adapter Gasket
12 Spiral Wound Gasket N06600/Graphite
27 or 51 Shim S31600
Keys 10*, 11*, 12*, 13*, 14*, 20*, 27*, and 51* Gaskets and Shims
Valve Size, NPS
ES EAS
1/2, 3/4,
1 or
1‐1/4
1‐1/2 2
1‐1/2 x 1 2 x 1
2 x 1 ‐ ‐ ‐
2‐1/2 3
2‐1/2 x
1‐1/2
1. Set number good for both ES and EAS valve.
1
2 ‐ ‐ ‐
3 x 1‐1/2
Standard Trim Cage
Whisper Trim I Cage
Key
Number
Set
27 or 51
Set
27 or 51
Set
27 or 51
Set
27 or 51
Set
27 or 51
(1)
10
12
13
(1)
10
12
13
(1)
10
11
12
13
20
Set
10
12
13
51
Set
10
11
12
13
14
51
(1)
10
12
13
(1)
10
11
12
13
14
-198 to 593_C
(-325 to 1100_F)
RGASKETX162
1R2859X0042
1R286099442
1R2862X0062
16A1936X012
RGASKETX172
1R3101X0032
1R309999442
1R3098X0052
16A1937X012
RGASKETX242
1R3101X0032
1R2861X0042
1R286099442
1R3098X0052
1U2152X0042
16A1936X012
RGASKETX182
1R3299X0042
1R329799442
1R3296X0042
16A1938X012
RGASKETX252
1R3299X0042
1R2861X0042
1R286099442
1R2862X0062
1R3296X0042
16A1936X012
RGASKETX192
1R3847X0032
1R384599442
1R3844X0052
16A1939X012
RGASKETX262
1R3847X0032
1R3100X0032
1R309999442
1R3098X0052
1R3844X0052
16A1937X012
Whisper Trim III Cage
WhisperFlo Cage
Key
Number
Set
10
12
13
51
Set
10
12
13
51
- - - - - - 4 6
Set
10
12
13
51
- - - - - - 6 ‐ ‐ ‐
Set
10
12
13
51
- - - - - -
-198 to 593_C
(-325 to 1100_F)
RGASKETX422
1R2859X0042(qty 2)
1R286099442
1R2862X0062
16A1936X012
RGASKETX432
1R3101X0032(qty 2)
1R309999442
1R3098X0052
16A1937X012
RGASKETX442
1R3299X0042(qty 2)
1R329799442
1R3296X0042
16A1938X012
RGASKETX452
1R3847X0032(qty 2)
1R384599442
1R3844X0052
16A1939X012
VALVE SIZE, NPS
ES EAS
3 4
3 x 2 4 x 2
4 x
2‐1/2
8 ‐ ‐ ‐
Number
27 or 51
27 or 51
27 or 51
6 x 2‐1/2
27 or 51
MATERIAL
FGM
Graphite/S31600
Standard Trim Cage
Whisper Trim I Cage
Key
Set
Set
Set
Set
(1)
10
12
13
(1)
10
11
12
13
14
(1)
10
12
13
(1)
10
11
12
13
14
Set
10
12
13
51
Set
10
13
-198 to 593_C
(-325 to 1100_F)
RGASKETX202
1R3484X0042
1R348299442
1R3481X0052
16A1940X012
RGASKETX272
1R3484X0042
1R3298X0032
1R329799442
1R3296X0042
1R3481X0052
16A1938X012
RGASKETX212
1R3724X0042
1R372299442
1J5047X0062
16A1941X012
RGASKETX282
1R3724X0042
1R3846X0042
1R384599442
1R3844X0052
1J5047X0062
16A1939X012
RGASKETX222
1U5081X0052
1U508599442
1U5086X0032
16A1942X012
RGASKETX232
10A3265X112
10A3266X082
Whisper Trim III Cage
WhisperFlo Cage
Key
Number
Set
10
12
13
51
- - - - - -
Set
10
12
13
51
- - - - - -
Set
10
12
13
51
Set
10
13
-198 to 593_C
(-325 to 1100_F)
RGASKETX462
1R3484X0042(qty 2)
1R348299442
1R3481X0052
16A1940X012
RGASKETX472
1R3724X0042(qty 2)
1R372299442
1J5047X0062
16A1941X012
RGASKETX482
1U5081X0052(qty 2)
1U508599442
1U5086X0032
16A1942X012
10A3265X152
10A3265X112(qty 2)
10A3266X082
ES Valve
July 2017
*Recommended spare parts
35
Page 36
ES Valve
July 2017
Instruction Manual
D100397X012
Keys 21*, 22*, and 23* PTFE‐Seat Disk Retainer, Disk Seat, and Disk
VALVE SIZE, NPS
ES EAS 316 SST CoCr‐A
1/2, 3/4, 1, 1‐1/4, or 2 x 1 1 1V710035072 1V710235072 1V710239012 1V710106242
1‐1/2 or 2‐1/2 x 1‐1/2
1‐1/2 x 1
2 or 3 x 2
2‐1/2 or 4 x 2‐1/2
3
4
All except Whisper Trim III cage ‐ ‐ ‐ 1V711833092 1V712033092 1V7120X0012 1V711906242
6
Whisper Trim III cage ‐ ‐ ‐ 23A4937X012 23A4938X012 ‐ ‐ ‐ 13A4936X012
8 ‐ ‐ ‐ 10A4446X012 20A4467X012 20A4467X022 20A4468X012
2 or 3 x 1‐1/2
2 x 1
4 x 2
3
6 x 2‐1/2
6
KEY 21
DISK RETAINER,
316 SST
1V710335072
1V712135072
1V710835072
1V710935072
1V711235072
1V711533092
KEY 22 DISK SEAT
1V710535072
1V712235072
1V710635072
1V711135072
1V711435072
1V711733092
1V710539102
1V712239102
1V710639102
1V711139102
1V711439102
1V711739102
KEY 23 DISK, PTFE
-73_ TO 204_C
(-100_ TO 400_F)
1V710406242
1V710106242
1V710706242
1V711006242
1V711306242
1V711606242
*Recommended spare parts
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher, easy-e, ENVIRO-SEAL, WhisperFlo, and Whisper Trim are marks owned by one of the companies in the Emerson Automation Solutions business unit
of Emerson Electric Co. Emerson Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other
marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Automation Solutions
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Cernay 68700 France
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
36
E 1973, 2017 Fisher Controls International LLC. All rights reserved.
Loading...