Fisher 61913 Parts Manual
Replacement Parts for Backsplash Faucets
fisher manufacturing company
2000-5003
SEAT WASHER
ANGLE STOP
W/ CROSS
HANDLET
ANGLE STOP
WITH KEY
12904
1792
62839
CONTROL VALVE
2000-7500
SCREW
2000-8000
RED BUTTON
2000-8001
BLUE BUTTON
LEVER HANDLE
2000-3002
BIBB CAP
DUCK GASKET
WASHER
LH SWIVEL STEM
RH SWIVEL STEM
1000-7502
SCREW
AND
73657
73641
18821
OR
18848
73521
LUBE
2000-0002
HANDLE LEVER KIT
54518
RH SWIVEL STEM
REPAIR KIT
OR
54526
LH SWIVEL STEM
REPAIR KIT
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
54445
16” SWING SPOUT
54429
14” SWING SPOUT
54410
12” SWING SPOUT
54402
10” SWING SPOUT
54399
8” SWING SPOUT
54380
6” SWING SPOUT
DOUBLE JOINT
SPOUT 7 1/4”
DOUBLE JOINT
SPOUT 13”
55867
2.2 GPM
AERATOR
54461
OR
55050
73805
SPOUT NUT
20020
SNAP RING
1600-5000
SPOUT
O-RINGS
73657
LUBE
19119
SWIVEL SPOUT
RETRO-FIT KIT
71498
ELBOWS
73794
SLIP JOINT KIT
FAHS-KF-4BSLL
Product Installation Guide
Since 1936, Fisher Manufacturing Company has manufactured
heavy-duty, high quality plumbing products and hardware
specialties for the food service industry. For three generations,
the Fisher family has adhered to a strict dedication of and
overall value. When you install Fisher products… you
install the best. Our hardware is manufactured with the
standardization of internal mechanisms. All chrome plating
is triple plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in both our
modern in-house testing center and in actual fi eld situations
under extreme conditions. Every detail is thoroughly checked.
Before we make our products available to you, they pass each
and every test. You get proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against defects
in materials or workmanship for a period of one year after
the date of original purchase. During this period Fisher
Manufacturing Company will replace a defective product
or part without charge to you, provided that the entire
product is delivered to Fisher Manufacturing Company. All
transportation and insurance charges for shipping the product
to and from Fisher Manufacturing Company must be borne
by you. Charges for transportation and insurance may, at
the option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim. This
warranty does not cover external fi nish (except at date of
original purchase) or labor costs not specifi cally authorized by
Fisher Manufacturing Company.
A full and complete copy of our One Year limited warranty is
available upon request.
Warning:This product can expose you to chemicals
including Lead, Nickel (Metallic), Di(2-ethylhexyl)
phathalate (DEHP) which are known to the State of
California to cause cancer, and Lead. Di(2-ethylhexyl)
phathalate (DEHP) which are known to the State of
Califorina to cause birth defects or reproductive harm.
For more information go to:
www.P65Warnings.ca.gov.
#62448 - SS FAUCET 4BSLH 6SS
#62316 - SS FAUCET 4BSLH 8SS
#62189 - SS FAUCET 4BSLH 10SS
#62049 - SS FAUCET 4BSLH 12SS
#61913 - SS FAUCET 4BSLH 14SS
#61794 - SS FAUCET 4BSLH 16SS
PART NO. 74837
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
REV. A
KEEP THIS MANUAL FOR FUTURE REFERENCE
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for Backsplash Faucets
Installation Instructions Continued
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure water supply is shut-off before beginning.
• Use pipe thread sealant on all threaded joints such as PST or Tefl on tape.
• Check the packaging for missing items BEFORE beginning installation. If
items are missing, contact your supplier.
Items needed for Installation:
• 1 - Medium Sized Crescent Wrenches
• 1 - Plumbers Tape or Pipe Thread Sealant
Step 1.
After unpacking items and checking for missing components, insert the gasket
into the groove on the concentric. Making sure gasket is in place, loosely mount
the concentric and fl ange onto the control valve body.
Step 2.
Mount control valve body to the backsplash by inserting the concentrics through
the backsplash and attaching slip joints. Tighten concentrics and attach elbows
and supply lines (not included) as required. Be sure to use pipe thread sealant
on all threads.
Step 3.
Apply O-ring lube to the O-rings on the swing spout. Make sure the white snap
ring is in place before mounting the swing spout. Mount the swing spout and
tighten the swing spout nut onto the faucet spout outlet.
Step 4.
Turn on water supply and check for leaks.
Step 2
Step 3
Slip Joint
Kit
1/2” Elbows
(not included)
4”
(101.6mm)
Ø7/8”
Swing Spout
Apply O-Ring
Lube Here
Step 1
Step 4
Gasket
Concentric
Flange
Loading...