First Alert FA148CP, FA168CPS User Manual



)$&36





)$&3



66HHFFXXUULLWW\\66\\VVWWHHP

PVV



3URJUDPPLQJ*XLGH

Y D

STAY

AWAY

OFF

BYPASS

TEST

MAX

CHIME

CODE

INSTANT

READY

FA260

OFF

AWAY

OFF

AWAY

STAY

MAX

TEST

BYPASS

INSTANT

CODE

CHIME

READY

FA560

K5305-5PRV2 10/03 Rev. A

TO ENTER PROGRAMMING MODE:

Local programming requires the use of an alpha keypad connected to the keypad terminals on the control.

POWER UP, then depress

mode, this method must be used to reenter program mode).

Initially, key:

Installer Code (4 + 1 + 1 + 2)

[✱] and [#]

both at once, within 50 seconds of powering up (if ✱98 was used to exit program

plus

8 + 0 + 0.

DATA FIELD PROGRAMMING PROCEDURES

Task Procedure

Go to a Data Field Entering Data

Review a Data Field

Deleting an Entry

Press [∗] + [Field Number], followed by the required entry. When the desired field number appears, simply make the required entry. When the last entry for a

field is entered, the keypad beeps three times and automatically displays the next data field in sequence. If the number of digits that you need to enter in a data field is less than the maximum digits available

(for example, the phone number fields *41, *42), enter the desired data, then press [ entry. The next data field number is displayed.

Press [#] + [Field Number]. Data will be displayed for that field number. No changes will be accepted in this mode.

Press [∗] + [Field Number] + [∗]. (Applies only to fields ∗40 thru *46, *94, and pager programming

fields)

∗

] to end the

INTERACTIVE MODE PROGRAMMING (∗56, ∗57, ∗58, ∗79, ∗80, ∗81, ∗82, ∗187)

Press

[✱] + [Interactive Mode No.]

requesting entries.

Interactive Mode

✱

56 Zone Programming Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800 RF

✱

57 Function Key Programming Unlabeled keypad keys (known as ABCD keys) for special functions

✱

58 Zone Programming Same options as *56 mode, but with fewer prompts. Intended for those familiar with

(Expert mode) this type of programming, otherwise *56 mode is recommended.

79 Output Device Mapping Assign module addresses and map individual relays/powerline carrier devices

✱ ✱

80 Output Programming

✱

81 Zone List Programming

✱

82 Alpha Programming

(for example, ✱56). The alpha display keypad will display the first of a series of prompts

Used to Program

transmitters.

4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc. Zone alpha descriptors

INITIALIZE DOWNLOAD and RESET DEFAULTS

✱

Initializes download ID and subscriber account number.

✱

Sets all data fields to original factory default values.

TO EXIT PROGRAMMING MODE:

✱

Exits programming mode and

mode, system must be powered down, and method A above used to enter the programming mode.

See field *88 for other *98 Program mode lockout options.

✱

Exits programming mode and

prevents

allows

re-entry by:

Installer Code + 8

Installer Code

+ 0 + 0. If

+ 8 + 0 + 0 or method 1 above.

✱

is used to exit programming

Special Messages

= OPEN CIRCUIT (no communication between Keypad and Control).

ENTRY ERROR

After powering up, This will revert to a “ delay by pressing

If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after you correct the programming.

= ERROR (invalid field number entered; re-enter valid field number).

AC, dI

Ready

[#] + [0].

(disabled) or

” message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this

Busy Standby

and

NOT READY

will be displayed after approximately 4 seconds.

– 2 –

352*5$00,1*)250

Entries apply to both the FA168CPS and

FA148CP

controls, except FA168CPS (partition entries) and are not applicable to the FA148CP. Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.

Field Function Data Entries Programmable Values

SYSTEM SETUP (✱20–✱29)

✱

INSTALLER CODE

✱

QUICK ARM ENABLE

✱

RF JAM OPTION

✱

QUICK (FORCED) BYPASS

✱

RF HOUSE ID CODE

✱

CHIME BY ZONE

✱

POWERLINE CARRIER DEVICE (X–10)

HOUSE CODE

✱

ACCESS CODE FOR

PHONE MODULE

✱

LONG RANGE RADIO OUTPUT

ZONE SOUNDS AND TIMING (✱31 – ✱39)

✱

SINGLE ALARM SOUNDING per ZONE

✱

FIRE ALARM SOUNDER TIMEOUT

✱

ALARM SOUNDER (BELL) TIMEOUT

✱

EXIT DELAY

✱

ENTRY DELAY #1 (zone type 01)

✱

ENTRY DELAY #2 (zone type 02)

AUDIBLE EXIT WARNING

∗37

✱

CONFIRMATION OF ARMING DING

✱

POWER UP IN PREVIOUS STATE

| | | [4112]

[0,0]

Part. 1 Part.2

[0]

[0,0]

Part. 1 Part. 2

| | |

Part. 1 Part. 2 Common

[0]

| [00]

(Partition 1 only)

[0]

| | [60,60]

Part. 1 Part. 2

| | [30,30]

Part. 1 Part. 2

Common zones use same delay as partition 1

| | [30,30]

Part. 1 Part. 2

[0]

[1]

[1,1]

[0,0]

[1]

DIALER PROGRAMMING (✱40 – ✱42)

Do not fill unused spaces. Enter 0–9; #+11 for '✱'; #+12 for '#'; #+13 for a 2-second pause. If fewer than the maximum digits entered, exit the field by pressing [✶]. The next data field number is displayed.

✱

PABX ACCESS CODE

✱

PRIMARY PHONE No.

✱

SECOND PHONE No.

| | | | | | | | | | | | | | | | | | |

Enter up to 20 digits. To clear entries, press ✱41✱ or ✱42

| | | | |

used, enter “∗ (#+11) 70” plus “# + 13” (pause).

entries shown in dashed boxes, which apply only to the

4 digits, 0–9

0 = no; 1 = yes

0 = no RF Jam detection; 1 = send RF Jam report UL: must be 1 if wireless devices are used

0 = no quick bypass UL: must be “0”

1 = allow quick bypass (code + [6] + [#] )

00 = disable all wireless keypad usage 01–31 = using 5827, 5827BD or 5804BD keypad [00,00,00]

0 = no; 1 = yes (select zones to chime on zone list 3, using *81 Menu mode)

0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 = J, #10 = K, #11 = L, #12 = M, #13 = N, #14 = O, #15 = P UL: not for fire or UL installations

00 = disable; 1st digit: enter 1–9; 2nd digit: enter # + 11 for "✱", or # + 12 for "#". UL: must be “00” for UL Commercial Burg. installations

0 = disable; 1 = enable

0 = no UL: must be “0”; 1 = yes

0 = sounder stops at timeout; 1 = no sounder timeout UL: must be “1” for fire install.

0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min; 4 = 16 min;

UL: For residential fire alarm installation, must be set for a minimum of 4 min (option 1); for UL Commercial Burglary installations, must be minimum 16 min (option 4)

00 - 96 = 0 - 96 secs; 97 = 120 secs SIA Installations: minimum exit delay is 45 seconds UL: see inst. instr. for requirements. Common zones use same delay as partition 1.

00 - 96 = 0 - 96 seconds 97 = 120 seconds 98 = 180 seconds 99 = 240 seconds

For UL Residential Burglary Alarm installations, must be set for a maximum of 30 seconds; entry delay plus dial delay should not exceed 1 min. For UL Commercial Burglar Alarm, total entry delay may not exceed 45 seconds.

See *35 Entry Delay 1 above for entries.

SIA Installations: minimum entry delay is 30 seconds

Enter up to 6 digits. To clear entries, press ✱40✱. If call waiting

0 = no; 1 = yes SIA Installations: must be enabled (enter 1)

0 = no; 1 = yes (wired keypads and RF) 2 = yes, RF only UL: must be “1” for UL Commercial Burglar Alarm inst.

0 = no; 1 = yes UL: must be “1”

✱

– 3 –

respectively

NOTE: Entry of a number other than one specified will give unpredictable results.

For fields *43 thru *46:

reporting format) is used. Enter 0 as the first digit of a 4-digit account number for Nos. 0000-0999. Exit field by pressing ✱ if only 3 digits are used. E.g., For Acct.

#+11| 2 | 3 | 4

, enter:

B234

✱

PARTITION 1 PRIMARY ACCT. No.

✱

PART. 1 SECONDARY ACCT. No.

✱

PARTITION 2 PRIMARY ACCT. No.

✱

PARTITION 2 SECONDARY ACCT.

✱

No.

PHONE SYSTEM SELECT

REPORT FORMAT

Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; #+15 for F. Enter

| | | / | | | | |

[1]

[77]

primary secondary

as the fourth digit if a 3-digit account number (for 3+1 dialer

[✱]

Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *43

[FFFF]

Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *44*. [FFFF]

Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *45*. [FFFF]

Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *46*. [FFFF]

If Cent. Sta. if Cent. Sta.

IS NOT

on a WATS line: 0=Pulse; 1=Tone;

IS on

a WATS line: 2 = Pulse; 3 = Tone

0 = 3+1, 4+1 ADEMCO L/S STANDARD 1 = 3+1, 4+1 RADIONICS STANDARD 2 = 4+2 ADEMCO L/S STANDARD 3 = 4+2 RADIONICS STANDARD 5 = 10-digit ADEMCO CONTACT ID® REPORTING 6 = 4+2 ADEMCO EXPRESS 7 = 4-digit ADEMCO CONTACT ID® REPORTING 8 = 3+1, 4+1 ADEMCO L/S EXPANDED

✱

SPLIT/DUAL REPORTING

9 = 3+1, 4+1 RADIONICS EXPANDED

[0]

0 = Standard/backup reporting only (all to primary)

Primary Phone No.

2nd Phone No.

1 = Alarms, Restore, Cancel Others 2 = All except Open/Close, Test Open/Close, Test 3 = Alarms, Restore, Cancel All 4 = All except Open/Close, Test All

✱

BURGLARY DIALER DELAY

5 = All All

[2]

0 = no delay UL: must be “0” 1 = 15 seconds SIA Installations: delay 2 = 30 seconds must be minimum of

✱

SESCOA/RADIONICS SELECT

✱

DYNAMIC SIGNALING DELAY

3 = 45 seconds 30 seconds

[0]

0 = Radionics (0-9, B-F) 1 = SESCOA (0-9 only reporting) Select “0” for all other formats.

Select delay from 0 to 225 secs, in 15-sec increments. 0 = no delay (both signals sent), 1 = 15 secs, 2 = 30 secs, etc.

✱

DYNAMIC SIGNALING PRIORITY

✱

56, *57, *58

MENU MODES

UL: Grade AA must be “0;” Grade A must be “15” max

[0]

These are Menu Mode commands, not data fields, for Zone Programming, Function

0 = Primary Dialer first; 1 = Long Range Radio first.

For UL Commercial Burglary installations that use a DACT and LRR, this field must be “0”.

Key Programming, and Expert Mode Zone Programming respectively. See page 2 and their respective sections in the Installation and Setup Guide for procedures.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (✱59 thru *68, *70 thru ✱76, and ✱89):

first

For 3+1 or 4+1 Standard Format:

not

A 0 (

#+10) in the

For Expanded or 4+2 Format:

not

A 0 (

#+10) in the

For Ademco Contact ID® Reporting:

not

A 0 (

#+10) in the

first

second

first

Enter a code in the

box will disable a report. A 0 (

Enter codes in

box will eliminate the expanded message for that report. A 0 (

box disables the report.

both

Enter any digit (other than 0) in the

SYSTEM STATUS REPORT CODES (✱59–

✱

EXIT ERROR REPORT CODE

✱

TROUBLE REPORT CODE

✱

BYPASS REPORT CODE

✱

AC LOSS REPORT CODE

✱

LOW BAT REPORT CODE

✱

TEST REPORT CODE

| [00] See box above. Use Scheduling mode to set periodic test reports,

| [00] See box above.

box: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.

not

#+10) in the

boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

UL: see installation instructions for requirements

✱

68)

second

box will result in automatic advance to the next field.

first

box, to enable zone to report (entries in the

[0] See box above.

not

#+10) in

both

boxes will disable the report.

second

boxes are ignored).

or use the following key commands: Each mode sets schedule 32 (FA168CPS) or installer code +[#] + [0] + 0 = test report sent every 24 hours schedule 08 (FA148CP) to the stated installer code +[#] + [0] + 1 = test report sent once per week repeat option; first test report sent 12 hours after command. installer code +[#] + [0] + 2 = test report sent every 28 days

– 4 –

✱

OPEN REPORT CODE

✱

ARM AWAY/STAY RPT CODE

Away Stay Away Stay Away Stay

✱

RF XMTR LOW BAT REPORT CODE

✱

CANCEL REPORT CODE

Part. 1 Part. 2 Common

| [00] See box on previous page.

[0,0,0] See box above.

Part. 1 Part. 2 Common

[0,0,0,0,0,0]

UL: must be enabled if wireless devices are used

RESTORE REPORT CODES (✱70 – ✱76)

✱

ALARM RESTORE RPT CODE

✱

TROUBLE RESTORE RPT CODE

✱

BYPASS RESTORE RPT CODE

✱

AC RESTORE RPT CODE

✱

LOW BAT RESTORE RPT CODE

✱

RF XMTR LO BAT RST RPT CODE

✱

TEST RESTORE RPT CODE

| [00] See box on previous page.

[0] See box on previous page.

UL: must be enabled if wireless devices are used

OUTPUT AND SYSTEM SETUP (✱77 – ✱93)

✱

DAYLIGHT SAVINGS TIME

START\END MONTH

✱

DAYLIGHT SAVINGS TIME

START\END WEEKEND

∗

79, *80, *81, *82

✱

AUTO STAY ARM

✱

CROSS ZONE TIMER

MENU MODES

This option not for use in UL installations.

✱

CANCEL VERIFY KEYPAD DISPLAY

✱

MISC. FAULT DELAY TIME

(used with Configurable Zone Types “digit 6”)

✱

PROGRAM MODE LOCKOUT

OPTIONS

✱

EVENT LOG FULL REPORT CODE

✱

EVENT LOG ENABLES

✱

OPTION SELECTION

| [4][10]

| [1][5]

These are Menu Mode commands, not data fields, for Output Device Mapping, Output Programming, Zone List Programming, and Alpha Programming respectively. See page 2 and their respective sections in the Installation and Setup Guide for procedures.

[3]

[0]

(assign cross zones on zone list 4, using *81 Menu mode)

[1]

[0]

UL: may only be used on non-burglar alarm/ non-fire alarm zones when used in fire and/or UL burglar alarm installation

[0]

| [00]

NOTE:

logged when any non-zero selection is made.

SIA Installations: Exit Delay should be enabled.

[3]

System messages are

[8]

– 5 –

0 = Disabled 1-12 = January-September (1 = Jan, 2 = Feb, etc) #+10 = October; #+11 = November; #+12 = December

0 = disabled, 1 = first, 2 = second, 3 = third 4 = fourth, 5 = last, 6 = next to last, 7 = third to last

0 = no, 1 = partition 1 only 2 = partition 2 only, 3 = both partitions

0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min 1 = 30 seconds 7 = 3 min #+13 = 10 min 2 = 45 seconds 8 = 4 min #+14 = 12 min 3 = 60 seconds 9 = 5 min #+15 = 15 min 4 = 90 seconds #+10 = 6 min 5 = 2 minutes #+11 = 7 min

0 = no, 1 = yes

0 = standard *98 installer code lockout (reentry only by

downloader or [∗] + [#] within 50 secs after power up)

1 = lockout [∗] + [#] reentry after *98 exit (reenter via

installer code or downloader only) 2 = not used 3 = lockout all local programming after *98 exit (reentry

via downloader only)

See box on previous page for report code entries.

0 = None; 1 = Alarm/Alarm Restore 2 = Trouble/Trouble Restore; 4 = Bypass/Bypass Restore; 8 = Open/Close.

Example:

“Open/Close”, enter 9 (1 + 8); To select all, enter #15. 0 = None

2 = Sounder Delay (delays sounding by 15 seconds) UL: if used, entry delay (*35) must be 30 sec. max.

4 = AAV UL: must use ADEMCO UVCM module 8 = Exit Delay Restart/Reset UL: must be disabled

#+12 = AAV and Exit Delay Restart/Reset

To select “Alarm/Alarm Restore”, and

See box above.

+ 11 hidden pages