Page 1
564 SS / 564 E Rectangular Face
Black 95400411 Nickel 95400413
Compatibility:
• 564 SS Fireplace
• 564 Electric Fireplace
The center deflectors must be in place when using this face to prevent
the facing above the fireplace from becoming too hot. If this face is
replacing a Lopi Grill (96200801), make sure to replace the center
deflectors.
Packing List:
• Face • 564 E Top and Bottom Brackets
• (2) 564 SS Top Brackets (w screws) • 564 E Top and Bottom Shims
• (2) 564 SS Upper Mounting Brackets • 564 E Upper Heat Shield
• (2) 564 SS Lower Mounting Brackets • (14) 8-32 Nuts
• (2) 10-24 1-1/2" Screws (564 SS only)
Installation Details – 564 SS
29”
36”
SIDE OF FIREPLACE
1”
0” TO 1”
NOTE:
This face has an adjustable bracket that allows for
different facing depths to be tucked under the face.
Page 1 of 6 7/19/07 © Travis Industries, Inc.
Page 2
564 SS / 564 E Rectangular Face
Black 95400411 Nickel 95400413
Installation – 564 SS
1 Remove the glass frame (see the owner's manual for details). Install face mounting brackets to the fireplae..
Remove and discard the nuts and bushings
above and below the firebox.
Discard the stock
bushings and nuts.
Upper
Bracket
Bracket Alignment - Facing material under 1/2” thick
Upper
Left
Lower
Left
Upper
Right
Lower
Right
Place the upper and lower brackets in place
and secure using the nuts included with this
kit.
Lower
Bracket
Repeat these steps for the opposite side.
Bracket Alignment - Facing material 1/2” to 1” thick
Upper
Left
Lower
Left
Discard the stock
bushings and nuts.
Upper
Right
Lower
Right
Page 2 of 6 11/19/07 © Travis Industries, Inc.
Page 3
564 SS / 564 E Rectangular Face
Black 95400411 Nickel 95400413
Installation – 564 SS (continued)
2 The facing and hearth (if applicable) must be installed prior to attaching the face. See the installation
manual for complete details.
Raised
Fireplaces
Note how the tile is 1”
(maximum) above the
base of the fireplace.
Floor-Level
Fireplaces
Maximum 1`” Hearth
Page 3 of 6 7/19/07 © Travis Industries, Inc.
Page 4
Installation – 564 SS (continued)
3 Install the face following the directions below.
564 SS / 564 E Rectangular Face
Black 95400411 Nickel 95400413
Attach the upper brackets
to the face with the
a
included nuts.
The face is secured to the fireplace
with four screws. Two of the screws
c
are fastened to the upper brackets
with press nuts. The lower screws
are included with the face.
Slide the face into place. The
tabs on the upper brackets insert
b
into the slots on the fireplace
brackets, holding the face in place
while the screws are tightened.
Plated Surfaces
Use denatured alcohol and a soft cloth to clean plated surfaces. Marks
left on the surface may damage the face.
Page 4 of 6 7/19/07 © Travis Industries, Inc.
Soft Cloth
Denatured
Alcohol
Page 5
564 SS / 564 E Rectangular Face
Installation – 564 Electric
1 Install the upper heat shield onto the 564 E fireplace.
Place the upper heat shield included with this kit
Remove the stock upper heat shield.
on top of the fireplace (note position of heat
shield). Place the stock heat shield on top of it
and secure with the same screws.
Black 95400411 Nickel 95400413
Page 5 of 6 7/19/07 © Travis Industries, Inc.
Page 6
564 SS / 564 E Rectangular Face
Black 95400411 Nickel 95400413
2 Place the face, face down, on a soft, non-scratching surface. Install the 564 Electric mounting brackets onto
the back of the face.
Attach the upper 564 E
bracket (and shim). Use the
c
nuts included with this kit.
Attach the lower 564 E bracket (and
shim). Use the nuts removed earlier and
b
one of the nuts included with this kit.
a
Remove and
discard the
hinge assembly
from the face.
Repeat steps “a” through
d
“c” for the opposite side.
Before installing the
e
face verify the lower
grill is centered.
Loosen the nuts and
adjust if necessary.
3 Pull the electric fireplace out of the mantel (or built-in location). Attach the cove covers and face following the
directions below. Slide the fireplace back into place to complete the installation.
b
Lift the face up slightly, tilt
it forward and insert the
top hooks until the face
locks in place.
a
Tilt the face back slightly and
insert the bottom hooks into
the slots on the fireplace.
Page 6 of 6 7/19/07 © Travis Industries, Inc.
Loading...