Russian
M44
Carb
Takedown
Guide
Clean
your
Saves
MADE
own
you
money
EASY
gun
with
repairs!
on
confidence.
Russian
}d44
Carbine
I Bolt Head/Extsactor
Bolt
2
Comector/Gilide
3 Firing Pin
4
Firing Fin Spring
5 Bolt
6 Cmking Pice
7
Bolt Assonbly
8 Tmg Screw
9
Ejoctor Spring Screw
l0 Ejecmr Spring/Feed
ll Ej€ctor
l2 Reeivq
ll Barr€l
Rear
14
Sight
15 Front Sigbt
| 6 Trigger
l7 Trigger Hinge Pin
l8 Trigg€r Spring/Bolt StoP
19 Bolt Siop Screw
20 Triggd Guard/Magazin€
2l FrontGuard Screw
Megazine
22
23 Floorplare t atch
24 Flmrplate Lrtch Screw
lnt€rruptq
Spring/Floorpla0e
Bar
Assembly
C'
A
WARNING:
Make sure the
entirely unloaded
starting
visually check some rounds
can hide.
Read every instruction
carefully using
as a reference.
only
gun
is
before
the disassembly;
picture
the
Copyright
@2003 By Radocy
Products,
Co.
RADOCY
1 800 356 4759
l.
Open
the bolt. To
remove
the
2. Hold
the cocking knob
clockwise;
the
front
of the bolt and
putting
and
turn
the striker in
pull
back
it
counter
the.fired
posltlon.
bolt hold
the
bolt
out.
the
trigger
back and
pull
Shown
how
the bolt should look.
3. Shde the bolt
off
and bolt
from
connector
head
the
front.
4.
Turn
the bolt head
counter-
should not
The
6.
be
striker
removed.
is
screwed into
It is
dovetail
mounted
broken have
the cocking knob
clockwise
in
the
a
at the
of the bolt connector
to unscrew
do
guide
tension.
it under
rear
not
could
until it
5. The
head.
bolt
gunsmith
stops
extractor
If it
replace.
of the bolt.
the striker. It may
force
use
As
control.
or the bolt
be broken. It is
you
start to release it keep
and remove
is
Use the forked
guide
as a wrench
be tight,
connector
under
it.
end
Remove
7.
released.
correct
For reassembly: Line
position.
8. With a tool,
the striker and
Do not
over tighten.
push
its
spring out
up the
magazine
the
from
the front. The
mark in
the
knob
cocking
with the
piece
is also
screw slot
for
the
floorplate
latch
toward
floorplate
the
the
rear
and
open.
lift
9. Squeeze
the
magazine
follower
to
L0. the magazine mainspring
inside
floorplate
the
bv a screw.
is retained
open
out.
-
the end
and
remove
Shown
it
back
and
outside
11. After
removed,
drift
remove the arm
the screw
and
out the cross
from
the
spring are
pin
show to
floorplate.
12. Driftthis
spring and arm.
pin
out to separate the
follower
M44
14.
Unscrew
this
L3.
Pull
the rod
out.
large
15. tf the rifle has a full
slide the barrel bands
Removal is not recommended(of
stretched stightly.
screw to
remove
bayonet.
the
stock
forward. The
It is recommended
with
the sight
the upper handguard,
barrel bands
and bayonet mount). The
you
that
not fit
will
leave
them
push
the
over the
on, unless
spring catches and
bayonet
mount.
bands can be
for
repairs.
16. Remove
the upper
handguard.
17. To
large
the
remove
at the
top
the
rear
stock,
of the
unscrew
gun.
18. Then
large
the
screw
on the bottom
of the masazine housins.
L9. The
release
to be
the stock cap.
removed,
small screw at the front will
unless
This
for repairs.
does
not need
20. Separate
the stock
the trigger
the barreled assemblv.
guardlmagazine
from
and
Unscrew
latch
the
down.
the
screw and remove
21.
The
magazine
I
floorplate
latch
is its
own
spring.
22. The
be a two-piece or one-piece
drift
disassembly.
ejector and feed intemrpter
it forward
out
of
its
dovetail.
depending
are on
*Note
the
on the model.
how
left
the
side
of the
Unscrew the
pieces
two
barreled
screw
fit
together
assembly. It may
at the rear
before
and
23.
Unscrew
the large
screw
24, Drtft
out the
trigger
spring/bolt
pin
and remove
the trigger
stop
and trigger.
underneath
The
trigger
not
be removed
the
barreled
spring/bolt
at this
assembly.
stop will
time.
Loading...