Finlux 42S9100-T User Manual [nl]

happy Finnish
42in 3D LED TV
42S9100-T
Customer Helpline Number: 0845 459 5282
Owner’s manual
Contents
Environmental Information ..................................... 2
Accessories included .............................................. 3
TV - Features ......................................................... 3
Safety Precautions and Important Information ....... 3
Viewing the TV ...................................................... 4
TV Control Buttons & Operation ............................. 4
Operation with the Buttons on the TV ..................... 4
Operation with the Remote Control ........................ 4
Remote Control ..................................................... 5
Inserting the Batteries into the Remote Control...... 8
Connect Power & Antenna ..................................... 8
Switching On/Off ..................................................... 8
First Time Installation.............................................. 8
Media Playback via USB Input ............................... 9
Menu Features and Functions ...............................11
Software Upgrade................................................. 23
Troubleshooting & Tips ......................................... 24
Licence Notications............................................. 24
Appendix A: Nero MediaHome Installation ........... 25
Appendix B: PC Input Typical Display Modes ...... 26
Appendix C: AV and HDMI Signal Compatibility
(Input Signal Types) .............................................. 26
Appendix D: Supported File Formats for USB Media
Browser ................................................................ 27
Appendix E: Supported DVI Resolutions .............. 28
SKY Remote Control Code ................................... 28
Specications ....................................................... 28
English - 1 -
Power cord and plug
The power cord plug should be easily accessible. If there is lightning or storms, or if the TV is not going to be used for a while (e.g. if going away on holiday), disconnect the TV set from the mains.
•Do not place the TV, furniture, etc. on the power cord or pinch the cord.
Handle the power cord by the plug, do not unplug the TV by pulling the power cord.
Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock.
Never make a knot in the power cord or tie it with other cords.
Power cords should be placed in such a way that they are not likely to be stepped on or provide a trip hazard.
• A damaged power cord/plug can cause re or give
you an electric shock. When damaged it must be
replaced, this should only be done by qualied
personnel.
Moisture and Water
•Do not use this TV in a humid or damp place (avoid using in the bathroom or near the kitchen sink)
•Do not expose this TV to rain or water, as this may be dangerous.
If any solid object or liquid falls into the cabinet, unplug the TV and have it checked by qualied
personnel before operating it any further.
Ventilation
The slots and openings on the TV set are intended for ventilation and to ensure reliable operation.
To prevent overheating, these openings must not be blocked or covered in any way.
Heat sources and Flames
Do not expose the TV to direct sunlight or other heat sources.
• The TV should not be placed near open ames or
sources of intense heat such as an electric heater.
• Ensure that no open ame sources, such as lit
candles, are placed on top of the TV.
Headphone Volume
Excessive sound pressure from earphones and headphones can cause hearing loss, please take care.
Wall Mounting (optional)
To prevent injury, this TV must be securely attached to the wall in accordance with the installation instructions.
Screen
Occasionally, a few non-active pixels may appear
on the screen as a xed blue, green or red point.
Please note that this does not affect the performance of your product.
• Take care not to scratch the screen with ngernails
or other hard objects.
Cleaning
Before cleaning, unplug the TV from the wall socket.
•Do not use liquid or aerosol cleaners. Only use a
soft, dry cloth.
Environmental Information
This television is designed to consume less energy to help save the environment. You can not only help to save the environment but you can also save money by reducing your electricity bills thanks to the energy efficiency features of this TV. To reduce energy consumption, you should take the following steps:
You can use the Power Save Mode setting, located in the Picture menu. If you set the Power Save Mode as Eco, the TV will switch to energy-saving mode and the luminance level of TV set will be decreased to the optimum level. Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.
If Picture Off is selected, “Screen will be off in 15 seconds.” message will be displayed on the screen. Select PROCEED and press OK to continue. The screen will be off in 15 seconds.
When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce energy consumption.
It is highly recommended that you activate the Power Save Mode setting to reduce your annual power consumption.
1) If the TV does not receive any input signal (e.g. from an aerial or HDMI source) for 5 minutes, the TV will go into standby. When you next switch-on, the following message will be displayed:
“Standby Cause No Signal”
Press OK to continue.
2) If the TV has been left on and not been operated for 4 hours, the TV will go into standby. When you next switch-on, the following message will be displayed.
“Standby Cause No Operation”
Press OK to continue.
English - 2 -
Accessories included
Remote Control x 2
Batteries: 2 x AAA
Instruction Book
Side AV Connection Cable
WiFi Dongle
USB Cable
NeroHome Media CD
3D Glasses x 8
TV - Features
3D Viewing: This product supports the viewing of
3D content from devices such as a High Denition
Satellite Receiver or Blu-ray Player via the HDMI input.
Remote controlled colour LCD TV
Fully integrated digital tuner
DVB-T2 Compliant
HDMI Inputs are for connecting a device that has
a HDMI socket
USB input
10000 programmes
OSD menu system
Scart socket for external devices (such as DVD
Players, PVR, video games, etc.)
Stereo sound system
Teletext
Headphone connection
Automatic programming system
Manual tuning
Automatic power down after up to six hours
Sleep timer
Child lock
Automatic sound mute when no transmission
NTSC playback
AVL (Automatic Volume Limiting)
PLL (Frequency Search)
PC input
Plug&Play for Windows 98, ME, 2000, XP, Vista,
Windows 7
Game Mode (optional)
Ethernet (LAN) for Internet connectivity
802.11n WiFi Support via USB dongle
DLNA
100Hz frequency scan
Safety Precautions and Important Information
Please read these instructions fully before installing or operating.
Preparation
Place the device on a solid even surface. For ventilation purposes, leave a free space of at least 10 cm all around the set. Do not place any objects on top of the set. Use this device in moderate climates. Operation temperature and operation humidity: 5ºC up to 45ºC, 85% humidity max. Note: Don’t block ventilation holes.
Intended Use
This device is used to receive and display TV programmmes. The different connection options expand the reception and display sources possible (various external devices). This device is only suitable for operation in dry interiors. This appliance is intended solely for private domestic use and may not be used for industrial and commercial purposes. We exclude liability in principle, if the device is not used as intended, or unauthorized
modications have been made. To operate your TV
in extreme ambient conditions may cause damage to the device.
WARNING: Never let people (including
children) with reduced physical, sensory or mental capabilities or lack of experience and / or knowledge use electrical devices unsupervised.
Children may not recognize the dangers of incorrect use. The swallowing of batteries can be fatal. Keep batteries out of reach of small children. If a battery is swallowed, immediately seek medical attention. Keep the packaging
lmsoutofreachofchildrentopreventtherisk
of suffocation.
Power source
The TV should be operated only from a 220-240 V AC, 50 Hz outlet.
Positioning the TV
For ventilation, please leave a clear space of at least 10cm all around the TV.
•Do not block the ventilation openings.
•Do not place the TV on sloping or unstable surfaces,
the TV may tip over.
To prevent damage to the TV, do not place any objects on top of the TV.
English - 3 -
Viewing the TV
TV Control Buttons & Operation
TV/AV
P/CH
MENU
1. Standby/On button
2. TV/AV button
3. Programme Up/Down buttons
4. Volume Up/Down buttons
Operation with the Buttons on the TV
Press button to decrease volume or button to increase volume. Press P/CH + button to
select the next programme or P/CH - button to select
the previous programme.
Press the or button at the same time to view main menu. In the Main menu select sub-menu using TV/AV button and set the sub­menu using or buttons. To see what options are available via the menu, refer to the menu system section of this
manual. Press the TV/AV button in the control panel on the TV to switch between AV modes.
Note: Function indications of the buttons will be displayed on the screen when pressed.
Operation with the Remote Control
Press the MENU button on your remote control to display the main menu screen. Use the “ ” or “ ” buttons to select a menu tab and press the OK button to select option. Use the “ ” / “ ” or “ ” / “ ” buttons to select or set an item. Press BACK or EXIT or MENU button to quit a menu screen.
Input Selection
Once you have connected external systems to your TV, you can switch to different input sources. Press the
- (SOURCE)” button on your remote control consecutively to select the different inputs.
Changing Channels and Volume
You can change the channel and adjust the volume using the V+/- and P+/- buttons on the remote.
English - 4 -
Remote Control
1. Standby / On
2. Channel list
3. Volume up-down
4. Menu on/off
5. OK / Channel list / Conrm
6. Return / Back
7. Internet Portal
8. My button 1 / Youtube (*)
9. My button 2 (**)
10. Coloured buttons (Red, Green, Yellow, Blue)
11. Mono-Stereo Dual I-II / Current language
12. Fast rewind (in media browser mode)
13. Pause (in media browser mode) / Timeshift
recording
14. Programme recording
15. Play (in media browser mode)
16. Stop (in media browser mode)
17. Fast forward (in media browser mode)
18. Subtitle on-off / Subtitle (in media browser
mode)
19. Image size
20. Teletext - Mix
21. Media Browser
22. Electronic programme guide
23. Exit
24. Navigation buttons
25. Quick menu
26. Info / Reveal (in TXT mode)
27. Programme up/down
28. Mute
29. Previous programme / Now (in EPG mode)
30. Numeric buttons
31. AV / Source
TV
NOTE: The Remote Control range is approximately 7m
/ 23ft.
Using My button 1 (*)
This button’s main function is to run Youtube link. However, if you want to change this function, you can press MY
BUTTON 1 for ve seconds when on a desired source,
channel or link, until the “MY BUTTON IS SET” message
is displayed on the screen. This conrms that the selected
MY BUTTON is now associated with the selected function.
Note that if you perform rst time installation, MY BUTTON
1 will return to its default function.
English - 5 -
Using My Button 2 (**)
This button’s main function is to switch to DVB-T, broadcasts. However, if you press MY BUTTON 2 for
ve seconds, you can set a function to it as described
in My Button 1.
Note that if you perform a first time installation, MY BUTTON 2 will return to its default function.
Remote Control
1. Standby / On
2. Volume up/down
3. Source selection
4. Info
5. Mute
6. Programme up/down
7. Image size
8. Mono-Stereo Dual-II / Audio-Subtitle language
English - 6 -
Connections
AV Connection
Cable (supplied)
Scart
Connection
(back)
VGA
Connection
(back)
PC/YPbPr Audio
Connection
(back)
HDMI
Connection
(back & side)
S/PDIF Optical Out
(back)
S/PDIF
Side AV
Connection
(side)
Headphone Connection
(side)
USB
Connection
(side)
Connector Type Cables Device
Y BPRP
AUDIO L&R
SIDE AV
HEADPHONE
YPbPr Video
Connection
(back)
CI
Connection
(side)
CAM
module
Subwoofer
Connection
(back)
NOTE: When connecting a device via the YPbPr or Side AV input, you must use the supplied connection cables to enable connection. See the illustrations above. | To enable PC audio, you will need to use the PC/YPBPR AUDIO CONNECTION cable’s WHITE & RED inputs. | If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.| When receiving DTV channels (Mpeg4 H.264) or while in Media Browser mode, output will not be available via the scart socket. | When using the wall mounting kit (optional), we recommend that you plug all your cables into the back of the TV before mounting on the wall. | Insert or remove the CI module only when the TV is SWITCHED OFF. You should refer to the module instruction manual for details of the settings.
English - 7 -
Inserting the Batteries into the Remote Control
HDMI 1
HDMI 1
1. Lift the cover on the back of the remote upward gently.
2. Install two AAA batteries. Make sure to match the + and - ends of the batteries in the battery compartment (observe the correct polarity).
3. Replace the cover.
Connect Power & Antenna
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Plug the aerial cable into the ANT socket on your TV.
First Time Installation
When turned on for the rst time, the “language
selection” menu appears. The message “Welcome please select your language!” is displayed and all
language options are listed alphabetically.
Press the “ ” or “ ” button to highlight the required language, press OK button to select. “First Time Installation” appears. Use “ ” or “ ” button to set the required country, and press “ ” button to select Search Type. Use “ ” or “ ” to set the desired search type. Available search types are digital and analog, digital only and analog only. When set, press “ ” to select Teletext Language. Use “ ” or “ ” button to set the “Teletext Language” and select “Scan Encrypted” using “ ” or “
” button. You can set Scan Encrypted as Yes if you
want to scan coded stations.
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC, 50 Hz.
To switch on the TV from standby mode either:
Press the “ ” button, P+ / P- or a numeric button on the remote control or press the “ ” button on the TV.
To Switch the TV Off
Press the “ ” button on the remote control or press
the “ ” button on the TV. The TV will now switch to standby mode.
To power down the TV completely, unplug the power cord from the mains socket.
Note: When the TV is switched to standby mode, the standby LED can blink to indicate that features such as Standby Search, Over Air Download or Timer is active. The LED can also blink when you switch on the TV from standby mode.
Press OK button on the remote control to continue and the following message will be displayed on the screen.
You must select YES to search and store broadcasts. The television will search for digital terrestrial TV broadcasts.
English - 8 -
Loading...
+ 21 hidden pages