Fiesta 16217 Owner's Manual

Customer Service Toll Free 1-800-396-3838

WARNING

Failure to follow all manufacturer’s instructions could result in serious personal injury and/or property damage.

Read and follow all Safety Statements, Assembly instructions, and Use and Care Manual Directions before attempting to assemble and cook.

CAUTION

Some parts may contain sharp edges, wear protective gloves if necessary.

CAUTION

THIS GRILL IS FOR OUTDOOR USE ONLY

Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A www.sears.com

Assembly and Operation

To Installer/Assembler: Leave these instructions with consumer. To Consumer: Keep this manual for future reference.

Liquid Propane Gas Grill

Model No.

SP5290B-37

259.162170

Table of Contents

Limited Warranty

Warranty.........................................................2

Safety..............................................................2

Caring for your equipment..............................3

Hardware........................................................6

Assembly...................................................7-22

Operation.................................................23-24

Cleaning and Maintenance......................25-26

Parts..............................................................27

Exploded view...............................................28

Troubleshooting.............................................29

Product Record IMPORTANT: Fill out the product record information below.

Model Number_____________________________

One Year Full Warranty on Kenmore Grill

If this grill is defective in material or worksmanship within one year from the date of purchase, contact Sears at 1-800-4-MY-HOME® to have it repaired free of charge.

Additional Full Warranty on Specific Grill Parts

For the time periods listed below, Sears will replace the following specific grill parts free of charge if they are defective in material of workmanship:

Lifetime on Cast Aluminum Lids and Bottoms Five years from purchase date on Stainless Burners

All warranty coverage excludes ignitor batteries and any grill part paint loss or rusting which are either expendable parts that can wear out from normal use in less than a year, or are conditions that can be the result of normal use, accident or improper maintenance.

All warranty coverage is void if this grill is used for commercial or rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

UPC (on carton) Label Lot # GG______________

Serial Number_____________________________

Date Purchased____________________________

WARNING

Combustion byproducts produced when

using this product contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

IF YOU SMELL GAS:

1. Sh

ut off gas supply to the

appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, immediately call your gas supplier or your

department.

fire

WARNING

• Do not store or use gasoline or

other flammable vapors and liquids

in the vicinity of this or any other appliance.

• An LP cylinder not connected

for use shall not be stored in the vicinity of this or any other appliance.

Do not use your grill until you have read and understood all the information in this manual. It is extremely important to be sure that:

• Your grill is properly assembled.

• There are no leaks in the gas supply system (see ‘Leak Testing’ section).

• The burner is properly assembled with the venturi tubes seated over the valve outlets (Figure 1 below) and there are no blockages present in the venturi tubes

(see ‘Cleaning Venturi Tubes’ section).

• Electrical supply cords and/or gas supply hoses are kept

away from any heated surfaces.

• Your grill is positioned in a safe location

(see ‘Installation’ section).

Figure 1.

• Ensure valve outlets (orifices) are assembled 3/8” (1 cm)

into the venturi tubes.

• Check to see that the valve outlets and venturi tubes are

parallel to the bottom of the base casting of your appliance.

Failure to ensure correct venturi tube assembly

may result in a hazardous fire

r explosion causing serious bodily injury

and/or property damage.

INSTALLATION

THE INSTALLATION OF THIS APPLIANCE MUST CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES:

• In Canada: must conform to CAN/CGA - B149.2 Propane Installation Code or CAN/CGA B149.1 Natural Gas Installation.

• In the U.S.A.: must conform to National Fuel Gas Code ANSI Z223.1.

When deciding where to place your appliance, follow these minimum clearance distances to adjacent combustivle materials:

• 24 inches (61 cm) from side of unit (See Figure 2)

• 18 inches (46 cm) from back of unit (See Figure 2)

WARNING

3/8"

VENTURI TUBE

AIR SLEEVE

VALVE OUTLETS

CASTING

Fig. 1

For residential use only. Do not use for commercial cooking.

CAUTION

WARNING

CARBON MONOXIDE HAZARD

Combustion byproducts include carbon monoxide which has no odor and can cause serious injury or death. Never use inside homes, vehicles or tents.

Call Grill Service Center For Help And Parts

If you have questions or need assistance during assembly, please call 1-800-396-3838. You will be speaking to a representative of the grill manufacturer and not a Sears employee. To order new parts call Sears at 1-800-4-MY-HOME®.

FOR YOUR OWN SAFETY:

• Only use your grill OUTDOORS in a well ventilated area

-- preferably 10 feet (3m) from your residence or any outbuildings.

• Always keep the area around your grill clear of any combustible materials, gasoline, or other flammable liquids.

• DO NOT operate this grill under overhead or unprotected construction.

• DO NOT obstruct the flow of combustion and ventilation air to the grill.

• DO NOT use in garages, sheds, breezeways, or other enclosed areas.

• DO NOT store a spare L.P. (propane) cylinder under or near your grill.

• DO NOT leave your grill unattended while in operation.

• DO NOT allow children to operate or play near your grill.

• DO NOT use while under the influence of alcohol or drugs.

• DO NOT install/use in or on recreational vehicles and/or boats

24"

(61cm)

18"

(46cm)

Fig. 2

MODEL MAY NOT BE EXACTLY AS SHOWN.

ELECTRICAL CAUTION

• If any accessory installed on this grill requires an external

electrical power source, it must be electrically grounded in accordance with local laws or in the absence of local laws, with the Canadian Electrical Code CSA C22.1 or in the U.S., with the National Electrical Code ANSI-NFPA 70.

• The three-prong plug provides protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

• Ensure all electrical supply cords and fuel supply hoses are kept well away from any heated surfaces.

L.P. GAS CYLINDER

Gas cylinders manufactured today have mechanisms to provide worry free grilling year round:

Q.C.C.1 or Type 1-Quick Connect Coupling Valve, ensure fast tank

hook-ups requiring only hand tightening. The redundant

valve system inhibits the flow of gas to the burner if the connection is not correct.

O.P.D. or Overfill Protection Device prevents accidental

gas leaks caused by cylinder ‘over-pressurization’, the leading cause of cylinder gas leaks. The float in the tank will automatically stop filling at 80% capacity, leaving a 20% area for the expansion of liquid. Without this safety feature, the relief valve may open and discharge propane, creating a potential safety hazard. An O.P.D. cylinder is easily distinguished by its triangular hand wheel valve. (Figure 3)

FILLING STOPS AT 80%

NEW OPD

HANDWHEEL

External threads on Coupling Valve.

O.P.D.

FLOAT

Fig. 3

1. SPECIFICATIONS

Self-contained propane gas grill systems are designed to be used only with a 20 lb (9.1 kg) propane cylinder, equipped with a Type 1 cylinder valve and incorporating an overfill protection

device (O.P.D).THE CYLINDER SHOULD NOT EXCEED 18 1/2" (472 MM) IN HEIGHT AND 12 1/2" (317 MM) IN DIAMETER. This grill cannot be connected to a #510 P.O.L

(ones with left-hand threads). The cylinder in accordance with the specifications of L.P. gas cylinders:

for your gas grill must be constructed and marked

type valve

THE CYLINDER MUST ALSO BE EQUIPPED WITH:

a. A shut-off valve terminating in a proper cylinder valve outlet

specified in current standards:

• Canada: CAN/CGA - 1.6a - M98 - Outdoor Gas Grills -

• U.S.: ANSI Z 21.58a-1998 OUTDOOR COOKING

APPLIANCES. b. A listed overfilling protection device (O.P.D.). c. A safety relief valve having direct communication with the

vapor space of the cylinder. d. A collar to protect the tank shut off valve. e. An arrangement for vapor withdrawal. f. A bottom ring for mounting.

SAFETY:

• Always turn off the cylinder valve tightly when your grill is not in use.

• Handle tank valves with care.

• Never connect an unregulated L.P. gas cylinder to your grill.

• Never store a spare cylinder under or near your grill when in use.

• Never subject any cylinder to excessive heat or direct sunlight.

• Always keep your in-use cylinder securely fastened in an upright position.

• Do not insert any foreign objects into the valve outlet. You may damage the back-check. A damaged back-check can be the source of a leak. Leaking propane may result in explosion, fire, severe personal injury or death.

• DO NOT fill the cylinder beyond 80% full.

WARNING

Amend. 1.

If the above instructions are not followed exactly, a fire causing death or serious injury may occur.

In Canada: The National Standards of Canada CAN/CSA-B339,

In the U.S.: U.S. Department of Transportation (D.O.T.)

DO NOT CONNECT TO A PROPANE GAS CYLINDER EXCEEDING THIS CAPACITY, OR USE A CYLINDER WITH ANY OTHER TYPE OF VALVE CONNECTION DEVICE.

The Type 1 valve is recognizable by the large external thread on the outlet part of the valve. Non Type 1 valves do not have these exterior threads. Any attempt to connect a regulator, with other than the: i) Mating Type 1 connector (recognized by the large black

coupling nut) or ii) Standard #510 P.O.L. fitting, by use of adapters or any means. Could result in damage, fire or injury and may negate the important safety features designed into the Type 1 system. The connection of a #510 P.O.L. fitting will not provide the flow control or temperature shut-off features built into the complete Type 1 System.

Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission.

other

2. TRANSPORTATION AND STORAGE:

WARNING: Although it is safe when used properly, careless

handling of the propane gas cylinder could result in fire, explosion, and/or serious injury.

ROPA

NE GAS IS HEAVIER THAN AIR, AND WILL COLLECT IN

LOW A

REAS, INCREASING THE ABOVE RISKS THEREFORE:

• ALWAYS use the cylinder

cap provided with your cylinder whenever the cylinder is not connected to your grill. (Figure 4)

• DO NOT store in a building, garage or any other enclosed area. Store in a well-ventilated area.

• DO NOT store near any gas burning apparatus or in any high-heat areas such as a closed car or trunk.

• Transport and store the cylinder in an upright position -- do not tip on its side.

• Store out of reach of children.

• DO NOT smoke while transporting a cylinder in your vehicle.

FILLING: FOR SAFETY REASONS, IF AN OPTIONAL L.P. GAS CYLINDER WAS SUPPLIED WITH YOUR GRILL, IT HAS BEEN SHIPPED EMPTY. THE CYLINDER MUST BE PURGED OF AIR AND FILLED PRIOR TO USING ON YOUR GRILL. WHEN GETTING YOUR CYLINDER FILLED:

• Allow only a qualified L.P. gas dealer to fill or repair your cylinder.

• DO NOT allow the cylinder to be filled beyond 80% full.

• Make sure the L.P. gas dealer checks the cylinder for leaks after filling.

If the above instructions are not followed exactly, a fire causing death or serious injury may occur.

HOSE & REGULATOR

PROPANE GAS MODELS:

Your grill is designed to operate on L.P. (propane) gas at a pressure regulated at 11" water column(2.74 kPa). A regulator preset to this pressure is supplied with the grill and MUST be used.

This regulator is equipped with the Q.C.C. Type 1, quick connect coupling system, which incorporates the following safety features: (Figure 5)

• I

t will not allow gas to flow until a

positive s

eal has been made. (Figure 6)

• I

t has a thermal element that will shut off the flow of gas

between 2

40 and 300°F (115 and150°C).

• I

t also has a flow-limiting device which,when activated, will

estrict the flow of gas to 10 cubic feet per hour (0.28 cubic

eters per hour).

CYLINDER CAP

RETAINER STRAP

LP TANK VALVE

Fig. 4

Fig. 6

REGULATOR

Q.C.C.I

Fig. 5

REGULATOR

Q.C.C.I

STRAIGHT

Prior to a

ttaching t

he p

ropane c

ylinder t

o t

he h

ose a

nd regulator,

e s

ure t

he c

ylinder v

alve a

nd the a

ppliance v

alves are O

FF. The

ylinder v

alve i

s turned off b

y r

otating t

he h

andwheel (

see F

igure 3)

lockwise (

left to r

ight) u

ntil it s

tops a

nd a

ll a

ppliance v

alves should

e i

n the off position. W

hen a

ttaching t

he r

egulator t

o t

he c

ylinder,

ake s

ure t

hat the s

mall p

robe i

n the n

ipple i

s centered in t

ating Q

.C.C. 1 c

ylinder v

alve (

see F

igure 6

). Tu

rn the r

ight h

and

hreaded Q

.C.C.1 b

lack n

ut o

nto t

he v

alve i

n a c

lockwise m

otion

ntil t

here i

s a p

ositive s

top. D

O N

OT U

SE A W

RENCH, HAND

IGHTEN O

NLY.

Should the large black thermally sensitive coupling nut be exposed to temperatures above 2

40 and 3

00°F, it will soften and allow the regulator probe to disengage from the cylinder valve -- thereby shutting off the flow of gas. Should this occur, do not attempt to reconnect the nut. Remove the entire regulator assembly, and replace it with a new one. (

See

‘R

EPLACEMENT PA

RTS’ s

ection i

n assembly i

nstructions o

ontact u

s a

t 1

-800-396-3838)

The cause of the excessive heat should be determined and corrected before operating your grill again. The regulator probe

also contains a flow-sensing element, which will limit the flow of gas to the regulator to a manageable amount (10 cubic feet per hour) in the event of a hose or regulator rupture. If it is evident that the flow control device has been activated, the cause of the excessive flow should be determined and corrected before using your grill again.

lease r

efer t

o t

he t

roubleshooting g

uide on p

age 2

9 o

ontact u

s 1

-800-396-3838.

NOTE:

IMPROPER LIGHTING PROCEDURES CAN

CAUSE THE FLOW CONTROL TO ACTI

VATE, RESULTING IN REDUCED HEAT OUTPUT. IF THIS IS SUSPECTED, RESET THE FLOW CONTROL BY SHUTTING OFF ALL BURNER CONTROLS AND THE CYLINDER VALVE. WAIT 30 SECONDS, THEN TURN THE CYLINDER VALVE ON EXTREMELY SLOWLY - WAIT 5 SECONDS AND TURN THE BURNER VALVE ON AND LIGHT AS NORMAL.

• Never connect a propane gas grill to an unregulated propane gas supply or any other gas. Do not attempt to alter the hose or regulator in any way.

• The connection fitting must be protected when disconnected from the propane tank. If the fitting is allowed to drag on the ground, nicks and scratches could occur resulting in a leak when connected to the propane tank.

PROPANE AND NATURAL GAS MODELS:

• Do not allow any grease (or other hot material) to fall onto

the hose, or allow the hose to come in contact with any hot surfaces of the grill.

• Visually inspect the entire length of the hose assembly

before each use of the grill. If it is evident there is excessive abrasion/wear, or the hose is cut, it must be replaced prior to using your grill. Only the hose assembly as specified in the Parts List should be used.

• Follow the ‘LEAK TEST’ instructions before lighting your

grill for the first time, every time a propane cylinder is refilled, if any gas component is changed, if the regulator flow-limiting device has been activated, after prolonged periods of storage or non-use or at least once per season.

WARNING

1/4" - 20 X 3/4" Carriage Bolt

#10-24 Wing Nut

(Cross Lighter)

Tube Spacer

(Cross Lighter)

1/4"-20 Knurl Nut

(Burners)

Cross Lighter/Burner Bagpack

(Cross Lighter)

1/4" - 20 X 2" Carriage Bolt

1/4"-20 Large Body Wing Nut

1/4" - 20 X 3/4" Carriage Bolt

#10-24 Knurl Screw

Push Pin (Side Panel)

Hinge Clip

1/4”-20 Tapered Wingnut

3/8"-16 Knurl Nut

(logo, Heat Indicator)

(Console)

(Lid)

Upper Tank Bracket

(Tank)

Master Bagpack

Handle

1/4-3/4 Washer

#10-24 Wing Nut

(Handle)

(6 pieces)

(16 pieces) (2 pieces)

(22 pieces)

(2 pieces)

(1 piece) (2 pieces) (2 pieces)

(1 piece)

(2 pieces) (2 pieces)

(3 pieces) (3 pieces) (3 pieces) (3 pieces)

HARDWARE

ASSEMBLY

Tab

No Tank Bracket

1. Turn leg assembly upside down as shown and insert caster plug. Make sure caster plug tab is in line with notch in leg.

2. T

urn leg assembly over and tap on a hard surface

until the caster plugs are fully seated.

Tank Bracket

Right hand leg assemblyLeft hand leg assembly

Notch

Caster Plug

Leg Assembly (Left Hand shown)

Locking Caster

3. Insert locking casters into the caster plugs on front of leg assemblies and press in until caster is fully seated as shown

Non-Locking Caster

Console mounting tabs are on front side of leg

4. Insert non-locking casters into the caster plugs on rear of leg assembiles.

assemblies.

5. Position left hand leg assembly as shown with console mounting tab facing up. Place non-tank side of bottom pan over bottom support. Attach bottom pan with 1/4”-20 x 3/4” carriage bolt and tapered wing nut.

Console mounting tab facing up.

Bottom Support

Bottom Pan

Tank opening on right side.

6. Position right hand leg assembly as shown, with console mounting tab facing up. Place tank side of bottom pan over bottom support. Attach bottom pan with 1/4-20 x 3/4” carriage bolt and tapered wing nut.

1/4”-20 Tapered Wingnut

Console mounting tab facing up.

1/4" - 20 X 3/4" Carriage Bolt

7. Attach console/valve assembly by positioning console over tabs and inserting two #10 knurl screws.

Locate Console on tabs as shown.

(Right side shown)

Mounting Hole

#10-24 Knurl Screw

8. Position side panels over legs and slide up into position. Bottom flange of side panel hooks over bottom support.

Push against leg assembly

Then slide up into position

+ 22 hidden pages