Fieldmann FZP 4216-B Operating Instructions
EN
FZP 4216 B
2
English .................................................................................................................................................................................3–26
Čeština .............................................................................................................................................................................27–50
Slovenčina ......................................................................................................................................................................51–74
Magyarul ........................................................................................................................................................................75–98
Polski ...............................................................................................................................................................................99–122
Slovenščina ...............................................................................................................................................................123–148
FZP 4216 B
Table of Contents
3
Chain saw
USER'S MANUAL
Thank you for purchasing this chain saw. Before you start using it, please, carefully read
this user's manual and save it for possible future use.
CONTENTS
1. GENERAL SAFETY INSTRUCTIONS ........................................................................................................................ 5
Important safety information .................................................................................................................................5
Packaging .......................................................................................................................................................................5
User's Manual .................................................................................................................................................................5
2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE ................................................................6
3. SAFETY INSTRUCTIONS ...............................................................................................................................................7
Before using the power tool ................................................................................................................................... 7
Safety of the operator, work equipment and clothing ...........................................................................7
Instructions for handling fuel ..................................................................................................................................9
4. DESCRIPTION OF THE POWER TOOL AND INCLUDED CONTENTS ...................................................10
Description of the power tool (see Fig. 1) .....................................................................................................10
5. INSTALLING THE BUMPER SPIKES, GUIDE BAR AND CHAIN .................................................................11
Installing the bumper spikes (Fig. 2) .................................................................................................................11
Installing the guide bar and chain .................................................................................................................. 11
6. FUEL AND CHAIN LUBRICATING OIL ................................................................................................................12
Filling the oil tank ........................................................................................................................................................12
Mixing the fuel mix .....................................................................................................................................................12
Storing fuel .....................................................................................................................................................................13
7. PREPARING FOR OPERATION ..............................................................................................................................13
Chain brake (Fig. 1, point 10) ............................................................................................................................... 14
Checking the working order of the brake ...............................................................................................14
8. TURNING THE CHAIN SAW ON AND OFF ......................................................................................................14
Starting a cold engine ............................................................................................................................................14
Starting a warm engine ..........................................................................................................................................15
Speed control system ..............................................................................................................................................15
Stopping the engine ................................................................................................................................................15
Checking chain lubrication .................................................................................................................................15
9. ADJUSTING THE CHAIN TENSION .......................................................................................................................16
EN
CHAIN SAW USER'S MANUAL
EN 4
Table of Contents
10. CUTTING ..........................................................................................................................................................................16
Safety brake (protection against kickback) ...............................................................................................16
Felling trees ....................................................................................................................................................................17
Cutting logs ...................................................................................................................................................................17
Log lying on the ground ....................................................................................................................................17
Log above the ground .......................................................................................................................................18
Lopping a fallen tree ...............................................................................................................................................18
11. CLEANING AND MAINTENANCE .......................................................................................................................18
Maintenance after every use .............................................................................................................................18
Cleaning the body of the chain saw ..............................................................................................................18
Maintaining the guide bar ...................................................................................................................................19
Normal maintenance of the guide bar ........................................................................................................19
12. SHARPENING THE SAW CHAIN ............................................................................................................................20
Equipment necessary for sharpening a saw chain ................................................................................20
Sharpening the teeth on the chain .................................................................................................................20
Filing the depth gauge ...........................................................................................................................................21
13. REPLACING THE SAW CHAIN ................................................................................................................................22
14. TECHNICAL SPECIFICATIONS ................................................................................................................................23
15. TROUBLESHOOTING .................................................................................................................................................24
16. DISPOSAL ........................................................................................................................................................................25
17. DECLARATION OF CONFORMITY ......................................................................................................................26
FZP 4216 B
General safety instructions
5
1. GENERAL SAFETY INSTRUCTIONS
Important safety notice
Carefully unpack the product and take care not to throw away any part of the packaging before you fi nd all
the parts of the product.
Store the product in a dry place out of reach of children.
Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical
shock, a fi re and/or serious injuries.
Packaging
The product is packed in a package that prevents damage during transport. This package is a resource and so
can be handed over for recycling.
User's manual
Before you start working with the machine, read the following safety and usage instructions. Acquaint yourself
with the operating elements and the correct use of the machine. Keep the user's manual in a safe place where
it can be easily retrieved for future use. Save the original packaging, including the internal packing material,
warranty card and proof of purchase receipt at least for the duration of the warranty.
If you need to ship this machine, pack it in the original cardboard box to ensure maximum protection during
shipping or transport (e.g. when moving or when you need to send this product for repair).
NOTE: If you hand over the power tool to somebody else, do so together with this user's manual.
Following the instructions in the included user's manual is a prerequisite for the proper use of the power tool.
The user's manual also contains operating, maintenance and repair instructions.
EN
The manufacturer takes no responsibility for accidents or damages resulting from not
following the instructions in this manual.
CHAIN SAW USER'S MANUAL
EN 6
Explanation of instruction labels on the machine
2. EXPLANATION OF INSTRUCTION LABELS ON
THE MACHINE
Before using the power tool, carefully read
the user's manual.
When operating the power tool, wear
protective aids such as safety glasses,
earmuffs, etc.
Always use two hands when operating
the chain saw.
While working use protective gloves.
Use solid insulating work footwear.
Attention! Danger of kickback
Warning! Attention!
FZP 4216 B
Safety Instructions
3. SAFETY INSTRUCTIONS
ATTENTION! The safety instructions in this user's manual are marked with the symbol containing critical
points, which one needs to pay attention to when operating the power tool to prevent serious or fatal injuries.
Please carefully study the instructions and adhere to them.
ATTENTION! This symbol indicates instructions that must be adhered to in order to prevent accidents that
could result in serious or fatal injuries.
NOTE: This symbol indicates a tip or instructions useful when operating the power tool.
Before using the power tool
Before using the power tool, carefully read the user's manual.
Do not use the power tool if your are under the infl uence of alcohol or narcotics, if you are tired or exhausted.
Do not use the power tool if your are taking medication, which could affect or limit your decision-making
abilities for safe operation of the power tool.
Do not use the power tool indoors, the emitted gases contain damaging carbon monoxide.
Never use the power tool under the conditions listed below:
– If the work surface is slippery or if weather conditions do not permit you to maintain a stable stance while
operating the power tool.
– If it is dark, heavy fog or under poor weather conditions, which limit visibility of the work area.
– During rain, during a storm or in strong winds or under conditions that could be dangerous when
operating the power tool.
If you are using the chain saw for the fi rst time, please consult with an experienced user before starting work.
Tiredness or physical exhaustion may lead to inattentiveness, which may result in serious injury
Limit the operating time of the power tool to approx. 10 minutes per single use and try to rest for
approximately 10-20 minutes between work sessions. Limit the total amount of work per day to
approximately 2 hours.
Make sure that you have the user's manual at hand in case you need to use it.
If you sell, loan or handover the power tool, make sure that you include the user's manual.
Never allow children or other persons that are insuffi ciently acquainted with the user's manual to use this
power tool.
EN
7
Safety of the operator, work equipment and clothing
When operating a chain saw, you should wear the following work clothing and protective aids:
– Helmet
– Safety glasses or protective face shield
– Work gloves
– Anti-slip work boots
– Earmuffs
CHAIN SAW USER'S MANUAL
EN 8
Safety Instructions
Furthermore, you should also have
– The included tools
– Suffi cient supply of fuel and chain lubricating oil
– Accessories for designating the work area (rope, warning signs)
– Whistle (to call for help)
– Hand saw or axe (to remove potential obstacles)
When working, never wear loose clothing, jewellery, that could become caught by the chain saw. Do not
wear sandals when working, do not work barefoot.
Check the work area, the item being cut and the cutting direction. Remove obstacles.
Never commence work if the work area is not cleared, if you do not have a stable stance and if you do not
have a planned escape route in the event of a falling tree.
Pay increased attention and keep passers-by and pets away from the work area at a distance of at least
2.5 times the length of the item being cut.
Check for damaged, worn out or missing parts of the power tool. Never use the power tool if it is damaged,
incorrectly adjusted or incomplete. Check that the chain stops turning when the throttle trigger is released.
Keep the handles dry, clean and free of oil and fuel stains.
Do not touch the muffl er, spark plugs or other metal parts of the engine when the power tool is running or
immediately after it is turned off - there is a risk of burns or injury by electrical shock.
Pay exceptional attention when cutting thin branches or trunks because fragile material may become caught
in the chain and fl ung towards the operator and may thus cause a loss of balance.
When cutting tensioned branches keep in mind that they will fl ing out when the wood fi bres are cut and the
tension is released.
Check for and remove dry branches that could come loose from the falling tree.
Make sure that the power tool is turned off when you put it down.
CAUTION danger of kickback! Kickback may occur when the nose of the guide bar comes into
contact with an item or if the material being cut clamps the chain in the cut. During contact with the item,
the chain saw may be fl ung with the guide bar moving up and back towards the operator. A clamped chain
may result in a fast backward movement of the guide bar towards the operator. Both these reactions may
lead to a loss of control over the chain saw and subsequent serious injuries. Do not rely only on the chain
saw's safety features. As the operator of the chain saw, you must constantly adhere to multiple rules to avoid
injuries or damages.
If you are acquainted with the kickback principle, you can reduce or eliminate the moment of surprise.
Unexpected reactions result in accidents.
If the engine is running, hold the chain saw with both hands with the right hand on the rear handle and the
left hand on the front handle. Firmly grasp the handle with the thumb going around towards the fi ngers.
A fi rm grip helps limit kickback and to keep the chain saw under control.
There must be no obstacles in the work area. When working with the chain saw, the loose end of the guide
bar must not touch a branch, trunk or another obstacle.
Cut with the engine running at high speed.
A stable stance must be maintained at all times when cutting, do not cut above shoulder height.
Adhere to the instructions of the manufacturer for lubricating and sharpening the chain.
Only use spare chains and guide bars specifi ed by the manufacturer or their equivalents.
FZP 4216 B
Safety Instructions
Instructions for handling fuel
The engine of the power tool is designed to use a highly fl ammable fuel mix. Never store fuel containers or refi ll
fuel in the vicinity of an open fl ame, wood stove, electrical lines, welding work or other sources of heat or fl ame,
which could lead to ignition.
Smoking is forbidden when operating the power tool and when refi lling fuel.
When refi lling fuel, make sure that the power tool is off and that there is no open fl ame in the vicinity.
If the power tool is sprayed with fuel, use a dry cloth to wipe away the stains.
After refi lling fuel, screw on the fuel tank cap and take the power tool at least 3 m away from the place where
it was refi lled and then start it up.
EN
9
CHAIN SAW USER'S MANUAL
EN 10
Machine description and included contents
4. MACHINE DESCRIPTION AND INCLUDED
CONTENTS
9
7
8
Fig. 1
Description of the power tool (see Fig. 1)
1. Throttle safety switch
2. Throttle trigger
3. Main power switch
4. Fuel tank cap
5. Oil tank cap
6. Front handle
6
5
10
4
7. Chain
8. Guide bar
9. Safety brake
10. Starting cord handle
11. Air fi lter cover screw
12. Choke lever
11
3
12
1
2
Included contents: Petrol chain saw, 405 mm guide bar, chain, plastic guide bar cover, calibrated fuel mixing
container, tool set with fi le.
FZP 4216 B
Installing the bumper spikes, guide bar and chain
5. INSTALLING THE BUMPER SPIKES,
GUIDE BAR AND CHAIN
ATTENTION! Always wear protective gloves when installing and inspecting the chain to prevent injury from
the sharp cutting edges on the chain.
Installing the bumper spikes (Fig. 2)
Using the included hex key and screw, attach the bumper spikes, see fi gure. For correct attachment, it is
necessary to screw out the exhaust cover bolt and after the installation to screw it back in. This bolt serves to
attach both the bumper spikes and the exhaust cover.
Installing the guide bar and chain
The safety brake lever (Fig. 1 point 10) must be disengaged (pull it towards the top handle)
Loosen two nuts and take off the sprocket cover (Fig. 3, point 1).
Seat the chain on to the guide bar and then thread on to the sprocket (pinion). At the same time, hold the
chain on the guide bar.
ATTENTION! The chain tensioning pin must fi t into the hole in the guide bar (Fig. 4, point 2). The position of
this pin can be adjusted using the chain tensioning screw (Fig. 5)
11
EN
1
Fig. 2
Fig. 4
1
2
CHAIN SAW USER'S MANUAL
Fig. 3
Fig. 5
EN 12
Installing the bumper spikes, guide bar and chain |Fuel and chain lubricating oil
Put the sprocket cover back. Do not fully tighten the screws, tighten by hand only, to make it possible to
tension the chain.
Tension the chain using the tensioning screw (Fig. 5) and then tighten the sprocket cover nuts using the
included tubular wrench
ATTENTION! The chain is correctly tensioned if it is possible to lift chain off the guide bar and its height in
the horizontal position in the middle of the guide bar is 3 to 4 mm.
6. FUEL AND CHAIN LUBRICATING OIL
Filling the oil tank
ATTENTION! A new chain requires a certain running-in period, which is usually 5 minutes. The lubrication
of the chain is very important during this phase. After this running-in period, check the chain tension and
readjust if necessary.
The oil tank on the supplied chain saw is empty. Fill this oil tank with oil prior to fi rst use of this chain saw.
Only use oil specifi ed for total-loss lubrication
Screw off the oil tank cap (fi g. 6, point 2).
Pour the oil into the tank (take care to prevent the oil from becoming dirty while fi lling the tank).
Screw on the oil tank cap
ATTENTION! Do not use oil that has already been used or processed because this could damage the oil
pump.
Mixing the fuel mix
ATTENTION! Never pour fuel into the fuel tank in a closed and unventilated location.
ATTENTION! Do not pour fuel in the vicinity of an open fl ame or a source of sparks.
ATTENTION! Do not overfi ll the petrol tank. Before starting the engine, make sure that all spilt fuel is wiped
away.
ATTENTION! If the engine is hot, DO NOT POUR IN FUEL.
For this type of two-stroke engine a mixture of lead-free petrol and two-stroke engine oil is used at a ratio of 25 : 1.
ATTENTION! A fuel mix that is mixed at a ratio other than 25 : 1 may damage the engine. Make sure that
this fuel mix is mixed correctly.
When mixing petrol with two-stroke engine oil, use only petrol containing NO ETHANOL or METHANOL (types
of alcohols).
Use quality petrol with an octane number of 95 or higher. This will help prevent possible damage to the fuel
system and other parts of the engine.
FZP 4216 B
Fuel and chain lubricating oil | Preparing for operation
13
EN
We recommend the use of the calibrated container
supplied with the chain saw for mixing the fuel mix.
DO NOT MIX THE PETROL AND OIL DIRECTLY IN
THE FUEL TANK.
Screw off the fuel tank cap (Fig. 6, point 1) and
pour in the fuel. Then screw the cap back on.
Storing fuel
Only store fuel in a clean, safe and approved canister.
Inform yourself about and adhere to local directives
related to the type and storage of canisters fi lled with
fuel.
ATTENTION! Fuel for two-stroke engines may separate. Prior to every use, thoroughly shake the canister
with fuel.
ATTENTION! Stored fuel ages. Do not mix more fuel than you expect to consume within one month.
Fig. 6
2
1
7. PREPARING FOR OPERATION
IMPORTANT: Follow instructions for preparing the fuel mix! Not following these instruction may damage
the engine! Do not use fuel that has been stored for longer than two months. A fuel mix stored for longer than
two months will cause problems at start up and lower engine performance. If the fuel mix is stored for longer
than two months, it should be removed and new fuel must be used.
Check for damaged, worn out or missing parts of the power tool. Never use the power tool if it is damaged,
incorrectly adjusted or incomplete.
Check whether any screws, nuts and installation elements are loose. Tighten any loose screws.
Check whether the air fi lter is dirty. Prior to starting work, remove all dirt from the air fi lter.
Check that the chain is tensioned. You can lift a correctly tensioned chain in the middle of the guide bar in the
horizontal position by 3 to 4 mm
Keep the handles dry, clean and free of oil and fuel stains.
Check the fuel tank for leaks.
Check the work area, the item being cut and the cutting direction. Remove obstacles.
Never commence work if the work area is not cleared, if you do not have a stable stance and if you do not
have a planned escape route in the event of a falling tree.
Pay increased attention and keep passers-by and pets away from the work area at a distance of at least
2.5 times the length of the item being cut.
CHAIN SAW USER'S MANUAL
EN 14
Preparing for operation | Turning the chain saw on and off
Chain brake (Fig. 1, point 10)
This chain saw is equipped with an automatic brake that stops the chain in the event of kickback. The brake is
engaged automatically by inertia acting on the ballast located under the rear cover. This brake can be operated
manually by tilting down the front protective frame towards the guide bar.
The brake is disengaged by pulling the front protective frame back towards the chain saw handle.
ATTENTION! Before every use, check that the chain brake is in working order in the following manner.
Checking the working order of the brake
Place the running chain saw on to the ground and for 1 to 2 seconds leave it at full speed.
Push the brake lever (Fig. 1, point 10) forward. The chain should stop immediately.
ATTENTION! If the chain stops slowly or does not stop at all, do not use the chain saw and contact an
authorised service centre.
If you wish to disengage the brake, pull the brake lever towards the top handle so that you hear the typical
click.
ATTENTION! Check that the chain brake is in order. A correctly functioning chain brake will protect you
against potential injury, which could result from kickback.
If the brake is not working properly, have it adjusted or repaired at an authorised service centre.
8. TURNING THE CHAIN SAW ON AND OFF
WARNING
Prior to starting the engine, make sure that the chain moves freely along the guide bar and is not touching
any foreign objects.
When the engine is idling, the saw chain must not be turning. Otherwise, contact an authorised service
centre to perform an inspection and remedy the problem.
Prior to starting the engine, make sure that the throttle trigger moves freely.
ATTENTION: Exposure to vibrations may damage the health of persons that suffer from circulatory or
nerve system problems. If any physical problems become evident, such as desensitisation, loss of sensitivity,
loss of usual strength or changes in skin colour, please contact a doctor. These systems usually manifest
themselves on fi ngers, hands or wrists.
Starting a cold engine
1. Set the power switch to the "I" position. (see Fig. 7, point 1)
2. Pull out the choke lever (Fig. 7, point 3) to the "OFF" position (=air supply turned off, i.e. choke turned on).
3. Place the chain saw fl at on the ground so that it is stable and pull on the handle of the starting cord until the
engine rotates (the engine will show signs of attempting to start) (Fig. 8).
4. At this point, push the choke lever (Fig.7, point 3) downwards to the "ON" position (=air supply turned on, i.e.
choke turned off) and start the engine by repeatedly pulling on the starting cord.
FZP 4216 B
Turning the chain saw on and off
15
EN
ATTENTION! Spinning the engine for too long
with the choke lever in the OFF position will result in
fl ooding of the engine and problems with starting it up.
5. Prior to starting work, leave the engine to warm
up for a few minutes to get up to operating
temperature.
Starting a warm engine
1. Set the power switch (Fig. 7, point 1) to the "I"
position.
1
5
2. Pull on the handle of the starting cord until the
engine starts up (Fig. 8). DO NOT USE THE CHOKE!
ATTENTION! In the event that the fuel in the fuel
tank was completely used up, after pouring in fuel,
repeat the steps for STARTING A COLD ENGINE.
Speed control
To increase speed, fi rst use the palm of your hand
to push down the throttle safety switch (Fig. 7,
point 4) and then use your fi nger to pull on the
throttle trigger (Fig. 7, point 5)
To lower the speed, release the throttle trigger
Stopping the engine
Release the throttle trigger (Fig. 7, point 5) and switch the power switch (Fig. 7, point 1) to the "0" position.
Fig. 7
3
4
Fig. 8
WARNING
The engine exhaust fumes contain chemical substances that are damaging to health. Never inhale these
fumes. Always start the chain saw outdoors.
Checking chain lubrication
ATTENTION! Adhere to safety provisions and
prevent the guide bar from coming into contact
Fig. 9
with the surface of the terrain.
Use this power tool safely and maintain
a minimum distance of 20 cm from the ground.
Before starting work, check the chain lubrication
and the amount of oil in the oil tank. Start the
chain saw and hold it above the ground. If you
see a growing oil stain then chain lubrication is
working properly. If there are no oil stains on the
ground, adjust the lubrication strength on the
underside of the chain saw (Fig. 9)
CHAIN SAW USER'S MANUAL
EN 16
Turning the chain saw on and off | Adjusting the chain tension | Cutting
If even then, the chain is not suffi ciently lubricated, clean out the oil outlet (under the sprocket cover), the top
chain tensioning hole and the oil lines, or contact an authorised service centre if necessary.
9. ADJUSTING THE CHAIN TENSION
ATTENTION! Due to the effect of higher temperatures, during operation the saw chain has a tendency to
lengthen. A longer chain becomes loose and could slide off the guide bar.
Loosen the sprocket cover fastening nuts.
Make sure that the chain is seated in the guiding groove of the guide bar.
Use a screwdriver to turn the chain tensioning screw (Fig. 5). Turn the tensioning screw until the required
tension is achieved (you should lift the chain in the middle of the guide bar in the horizontal position to
a height of 3 to 4 mm).
Firmly tighten the guide bar fastening nuts.
ATTENTION! Do not tension the chain excessively. Excessive tension of a warm chain may result in
excessively tension when it cools down.
10. CUTTING
ATTENTION! Before proceeding, please read the chapter "Safety instructions". We recommend that you
gain experience by cutting smaller logs. In this way you will also get to know the chain saw.
Always adhere to safety instructions. The chain saw may only be used for cutting wood.
It is forbidden to cut any other materials. Vibrations and kickback differ for various materials. Do not use the
chain saw as a lever for lifting, moving or splitting material. It is forbidden to attach any parts or jigs other
than those specifi ed in the technical documentation.
It is not necessary to push the chain saw into the cut. When the engine is running at full speed, push the
chain saw down lightly.
If the chain jams in the cut, do not attempt to free it by pulling, rather stretch open the cut using a wedge or
crowbar.
Safety brake (protection against kickback)
This chain saw is equipped with an automatic chain brake that, if it works correctly, immediately stops the
chain in the event of kickback. It is necessary to check the working order of the chain brake before every use
of the chain saw. Run the chainsaw at full speed for 1 - -2 seconds and then tilt the front protective cover.
The chain must stop immediately even when the engine is running at high speed. If the chain stops slowly
or does not stop at all, please contact an authorised service centre.
It is extremely important to check the working order of the chain brake and the sharpness of the chain
before every use to ensure that the necessary level of safety in the event of a kickback is maintained.
FZP 4216 B
Cutting
Removing safety accessories, incorrect maintenance or when using unsuitable guide bars or chains may, in
the event of kickback, result in serious injuries.
Felling trees
Decide about the direction in which the tree will fall,
respecting the wind direction, incline angle of the
3
tree and location of the branches, and consider all
other factors before cutting.
The area around the tree must be clear, without
obstacles, and must enable a stable stance. The
escape route must be passable.
Cut a wedge into one third of the tree's diameter on
the side to which the tree should fall.
1
2
(see Fig. Felling, point 1)
From the opposite direction perform a separation
Fig. Cutting trees
cut at a level above the wedge cut. (see Fig. Felling,
point 2)
The tree will fall in the direction towards the wedge cut. (see Fig. Felling, point 3)
ATTENTION! When felling trees, inform other people in the area about the potential danger.
Felling trees requires experience and we do not recommend performing this task without the necessary
experience.
Cutting logs
ATTENTION! Always maintain a stable stance. Do not step on logs.
17
EN
ATTENTION! Before starting work, check that all components are in their place and that all nuts and bolts
are tightened.
The log being cut may roll away. Especially when cutting on a slope, always stand above the log being cut.
Prevent kickback of the saw by following the instructions in chapter "Safety instructions".
Before starting work, assess the direction of the force causing the cut trunk to bend. The fi nal cut needs to
always be done from the opposite side of where the bending force is acting to prevent the guide bar from
being clamped inside the cut.
Only carry the chain saw with the engine turned off and the guide bar protected by the protective cover.
Log lying on the ground
Cut it halfway through, then roll it over and
complete the cut from the other side.
CHAIN SAW USER'S MANUAL
EN 18
Cutting | Cleaning and maintenance
Log above the ground
In part "A" make a cut from below to a third of the
log and then complete the cut from above. In part
"B" make a cut from above to a third of the log and
then complete the cut from below.
AB
1
2
1
Removing a fallen tree
2
1
First fi nd out to which side the branch is bent. Then
make the initial cut from the side of the bend and
then complete the cut from the opposite side.
ATTENTION! A bent branch may spring up.
2
11. CLEANING AND MAINTENANCE
ATTENTION! Prior to cleaning, inspecting or repairing the chain saw, its engine must be turned off and
cold and the spark plug must be removed to prevent accidentally starting the engine.
Maintenance after every use
Remove the guide bar and use a brush to clean away accumulated sawdust from the entire chain saw. Use
a spatula or screwdriver to remove stubborn dirt.
Air fi lter:
Loosen the screw (Fig 1, point 11) and remove the air fi lter cover. Take out the fi lter insert and use a brush to
remove the dust. If the fi lter insert is clogged with dust, dismantle into 2 parts and wash it out in petrol. If you
are using compressed air, blow from the inside out.
Lubricating hole:
Take off the guide bar and check the passage of the lubricating hole.
Guide bar:
After taking off the guide bar, remove dust from the grooves and the lubricating hole.
Other parts:
Check for any oil leaks, loose mounts and damaged main parts, particularly in the location where the
handles and the guide bar are mounted. Any identifi ed defects must be repaired before the chain saw is used
again.
FZP 4216 B
Cleaning and maintenance
19
Cleaning the body of the chain saw
Keep the body of the chain saw clean. When cleaning, use a soft cloth dipped in a soap solution. Use this cloth to
meticulously clean the body of the chain saw.
EN
Maintaining the guide bar
Most problems with the guide bar arise due to
uneven wear.
Guide bar
groove
Uneven wear occurs mainly as a result of an
incorrectly sharpened chain or an incorrectly set
depth gauge.
Guide bar
When the guide bar is worn out unevenly, the
guiding groove is widened (see Picture). The result
is a rattling chain and rivets falling off. The chain
saw cannot be used for straight cuts. In such
a case, replace the guide bar for a new one.
Always check the condition of the guide bar
before sharpening the chain. Using a worn
Standard guide
bar
out or damaged guide bar is very dangerous.
Using a worn out or damaged guide bar will
result in damage to the chain. Cutting with such
a power tool will also be much more diffi cult and
demanding.
Normal maintenance of the guide bar
Remove the guide bar from the body of the chain saw.
Regularly remove sawdust from the guide bar groove. For cleaning use a spatula or a wire.
Clean oily grooves at the end of every work day.
Replace the guide bar if:
• it is bent or cracked
• its groove is very damaged or worn out
Guide bar
with uneven
wear
NOTE: To replace the guide bar, follow the instruction contained in this user's manual. You will fi nd the
correct guide bar type in the technical specifi cations.
CHAIN SAW USER'S MANUAL
EN 20
Sharpening the saw chain
12. SHARPENING THE SAW CHAIN
Keep the saw chain sharp. Cutting will be signifi cantly faster and most importantly safer. A blunt saw chain
increases wear on the sprocket, guide bar, chain and engine. If you need to push on the saw and only sawdust
with a few splinters are produced then this means that the chain is blunt.
For this task, we recommend that you contact an authorised service centre
Equipment necessary for sharpening a saw chain
Round fi le as per technical specifi cations
Depth gauge
File guide
Vice
Medium-size fl at fi le
Sharpening the teeth on the chain
Use the fi le guide set at an angle of 30° (mark A, see
fi gure).
Set the saw chain tension to the correct level.
Fasten the guide bar in a vice so that you have the
chain in a stable position.
NOTE: Do not fasten the chain itself.
A
B
Push the round fi le, inserted in the fi le guide, into
the groove between the top plate and the depth
gauge on the chain. The chain should be touching
both the top plate as well as the depth gauge (see
fi gure)
NOTE: File in the middle of the guide bar.
NOTE: In the fi gure you can see the position of the fi le guide and the direction for fi ling the teeth on the left
side of the chain.
Place the fi le guide at the required angle (mark A, see fi gure). Check that the mark is at 30° on the fi le guide
aligned with the centre of the guide bar. This will ensure that you will fi le at an angle of 30°.
File the tooth in the direction from inside out (in direction B, see fi gure) until it is sharp. File only in this
direction.
NOTE: Two to three passes of the fi le should be suffi cient to sharpen the tooth.
FZP 4216 B
Filing the depth gauge
As a result of sharpening the teeth on the chain, the
depth gauge tolerance is reduced. After every second
or third sharpening, it is necessary to adjust the depth
gauge setting.
Place the depth gauge adjustment jig (see fi g.,
point 1) fi rmly on the top edge of two teeth. Make
sure that the groove of the jig is in the groove of the
depth gauge (see fi g., point 2.)
Use a medium-sized fl at fi le (see fi g., point 3). File
the depth gauge (see fi g., point 4) to the level of the
depth gauge adjustment jig.
Remove the depth gauge adjustment jig. Using
a fl at fi le, round the front edge of the depth gauge
(see fi gure). When fi ling, adhere to the prescribed
values (see fi g., point 5).
NOTE: After the chain has been sharpened by
hand several times, have the saw chain sharpened
at an authorised service centre or sharpen it on
a special sharpening machine.
This will renew the even sharpness of all teeth.
EN
Sharpening the saw chain
4
3
1
5
0.6 mm
21
2
CHAIN SAW USER'S MANUAL
EN 22
Replacing the saw chain
13. REPLACING THE SAW CHAIN
ATTENTION! When replacing the saw chain, do not clamp the chain saw or the guide bar in a vice.
Always replace the chain if the teeth are excessively worn out and they cannot be sharpened or if the chain
snaps. Use only an original spare chain according to the specifi cations in this user's manual. When replacing
the saw chain, always also replace the cogged wheel of the sprocket. This will ensure the correct position of the
chain during movement. (Note: You will fi nd the specifi cations of the correct chain type and the cogged wheel in
the technical specifi cations.)
Loosen and remove the bar guide bolt.
Remove the sprocket cover.
Remove the saw chain.
Wind the new chain around the cogged wheel,
then along the top groove of the guide bar and
around the guide bar nose.
ATTENTION! Check that the saw teeth are facing
in the correct direction. Put on the chain so that the
teeth on the top side of the guide bar are facing
towards the guide bar nose (see fi gure).
Before placing the sprocket cover into position,
check that the chain tensioning pin is inserted into the adjustment hole on the guide bar.
Put the sprocket cover back on to the body of the chain saw.
Fasten the sprocket cover using the guide bar bolt.
ATTENTION! Only tighten the bolt by hand.
Adjust the tension of the saw chain.
Tighten the guide bar bolt.
ATTENTION! Check that you have not placed the saw chain on the guide bar in the opposite direction.
Otherwise, the chain saw will exhibit excessive vibrations and will not cut.
FZP 4216 B
14. TECHNICAL PARAMETERS
Technical Parameters
23
EN
Type..............................................................................................................................................................................................FZP 4216 B
Engine ............................................................................................................................................................................................. 45.0 cm
Maximum engine power.........................................................................................................................................1.6 kW /7500 rpm
Maximum engine speed with chain ................................................................................................................................10,500 rpm
Maximum engine speed when idling .................................................................................................................................3,000 rpm
Guide bar length ........................................................................................................................................................................... 405 mm
Chain pitch ................................................................................................................................................................................. 0.375 inch
Guiding groove width ....................................................................................................................................................................1.5 mm
Number of chain links .................................................................................................................................................................. 57 links
File diameter ........................................................................................................................................................................................4 mm
Weight (without the guide bar and chain) ...............................................................................................................................5.5 kg
Dimensions ............................................................................................................................................................360 x 160 x 165 mm
Fuel mix (petrol : oil) .......................................................................................................................................................................... 25 : 1
Fuel tank capacity ........................................................................................................................................................................... 580 ml
Oil tank capacity .............................................................................................................................................................................. 250 ml
Chain lubricating oil ........................................................................................................................................Total-loss lubrication oil
Chain lubrication system ...................................................................................................................... Adjustable automatic pump
Sound pressure level........................................................................................................................................................LpA: 96dB (A)
Guaranteed emission level of sound power .......................................................................................................... LwA: 114dB (A)
Vibrations* – front handle .........................................................................................................................................................8.5 m/s
Vibrations* – rear handle .......................................................................................................................................................... 8.5 m/s
* If you fi nd that the vibrations being transferred to the handle have become noticeably worse compared to
the condition when the chain saw was new, check the wear on the silentblocks (rubber coated mounting
elements) and if necessary contact an authorised service centre to have them replaced.
ATTENTION! Working with a chain saw with an incorrectly working vibration shock absorption system may
lead to health problems.
3
2
2
CHAIN SAW USER'S MANUAL
EN 24
Disposal
15. TROUBLESHOOTING
CAUTION: always turn off the unit and disconnect the spark plug before carrying out the checks recommended
in the table, except for the cases where the unit needs to be running.
When all possible causes have been checked and the problem remains unsolved, please contact an
authorised service centre. When you identify a problem that is not included in the table, please contact
an authorised service centre.
PROBLEM POSSIBLE CAUSES SOLUTION
The motor cannot be
started or stops several
seconds after starting.
(Make sure that
the switch is in
position „I“)
The motor starts but does
not properly increase its
speed or does not run
properly at high speeds.
The motor does not reach
full speed and/or emits
too much smoke.
The engine starts, works
and accelerates, but does
not maintain idling speed.
The guide bar and chain
heat up and smoke while
running
The motor starts but the
chain is not running.
CAUTION: when the motor
is running, never
touch the chain
1. The spark plug is
not fi ring
2. The motor is
fl ooded
The carburettor must
be adjusted.
1. Check the
petrol - oil mixture.
2. Dirty air fi lter.
3. The carburettor
must be adjusted.
The carburettor must
be adjusted.
1. Empty chain oil
tank
2. Chain is overly
tensioned
3. Lubrication system
not working
properly
1. Chain brake
engaged
2. Chain is overly
tensioned
3. Guide bar and
chain installation
4. Damaged chain
and/or guide bar
5. Damaged clutch
and/or pinion
1. Check that the spark plug is fi ring. If the spark plug is not
fi ring, repeat the test with a new spark plug (WXL7T).
2. Take out the spark plug and pull the starting cord several
times. Then reinsert the cleaned spark plug and start
without using the choke.
Contact an authorised service centre to have the
carburettor adjusted
1. Only use fresh petrol and oil suitable for two-stroke
engines.
2. Clean it; see instructions in chapter 11.
3. Contact an authorised service centre to have the
carburettor adjusted
Contact an authorised service centre to have the
carburettor adjusted.
1. The oil tank must be fi lled up every time when the fuel
tank is fi lled.
2. Tensioning the chain; see instructions in chapter 5.
3. Allow it to run at maximum speed for 15-30 seconds.
Stop and check whether oil is dripping from the tip of the
guide bar. If there is oil there, the faulty operation may be
caused by a loose chain or damaged guide bar. If there
is no oil there, contact an authorised service centre
1. Disengage the chain brake; see chapter 7.
2. Tensioning the chain; see instructions in chapter 9.
3. See instructions in chapter 5.
4. See instructions in chapter 11. and 13.
5. If necessary, replace it; contact an authorised service
centre
FZP 4216 B
Declaration of Conformity
16. DISPOSAL
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
MATERIALS
Dispose of used packaging material at a site designated for waste in your municipality.
The machine and its accessories are manufactured from various materials, e.g. metal and
plastic.
Take damaged parts to a recycling centre. Inquire at the relevant government department.
This product meets all the basic requirements of EU directives that apply to it.
Changes in the text, design and technical specifi cations may be made without prior notice and we reserve
the right to make these changes.
User s manual in the original language.
25
EN
CHAIN SAW USER'S MANUAL
EN 26
Notes
>Zd/KEK&KE&KZD/dz
ͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺͺ
DĂŶƵĨĂĐƚƵƌĞƌ
&^dZĂƐ
ĞƌŶŽŬŽƐƚĞůĞĐŬĄϮϭϭϭϭϬϬϬϬWƌĂŚĂϭϬnjĞĐŚZĞƉƵďůŝĐ
sdŶŽϮϲϳϮϲϱϰϴ
WƌŽĚƵĐƚďƌĂŶĚWdZK>,/E^t&/>DEE
dLJƉĞŵŽĚĞů &WϰϮϭϲ
ϭϴŬtϰϱĐŵϯϭϬϬϬϬŵŝŶ
dŚĞƉƌŽĚƵĐƚŝƐŝŶůŝŶĞǁŝƚŚĚŝƌĞĐƚŝǀĞƐĂŶĚƌĞŐƵůĂƚŝŽŶƐůŝƐƚĞĚďĞůŽǁ
E/^KϭϮϭϬϬϮϬϭϬƐĂĨĞƚLJŽĨŵĂĐŚŝŶĞƌLJ
E/^KϭϭϲϴϭͲϭϮϬϭϭŵĂĐŚŝŶĞƌLJĨŽƌĨŽƌĞƐƚƌLJͲƐĂĨĞƚLJ;>s'^Ϳ
E/^KϭϰϵϴϮϮϬϬϵĂŐƌŝĐƵůƚƵƌĂůĂŶĚĨŽƌĞƐƚƌLJŵĂĐŚŝŶĞƌLJʹD
E/^KϵϮϬϳϯϳϰϰͲϮϬϬϬϭϰŶŽŝƐĞ
ZŽ,^ϮϬϭϭϲϱh
ůĂďĞůϭϲ
WůĂĐĞŽĨŝƐƐƵĂŶĐĞWƌĂŐƵĞEĂŵĞ/ŶŐĚĞŶĢŬWĞĐŚ
ŚĂŝƌŵĂŶŽĨƚŚĞŽĂƌĚ
ĂƚĞŽĨŝƐƐƵĂŶĐĞϭϰϮϬϭϳ^ŝŐŶĂƚƵƌĞ
FZP 4216 B
Obsah
27
Řetězová pila
NÁVOD K OBSLUZE
Děkujeme vám, že jste si zakoupili tuto řetězovou pilu. Než ji začnete používat, přečtěte
si, prosím, pozorně tento návod k obsluze a uschovejte jej pro případ dalšího použití.
OBSAH
1. VŠEOBECNÉ BEZPEČNOSTNÍ PŘEDPISY ........................................................................................................29
Důležitá bezpečnostní upozornění .................................................................................................................29
Obal ..................................................................................................................................................................................29
Návod k použití ...........................................................................................................................................................29
2. VYSVĚTLENÍ ŠTÍTKŮ S POKYNY NA STROJI ................................................................................................... 30
3. BEZPEČNOSTNÍ POKYNY .......................................................................................................................................31
Před použitím stroje ..................................................................................................................................................31
Bezpečnost obsluhy, pracovní vybavení a oděv ...................................................................................31
Pokyny při manipulaci s palivem .....................................................................................................................33
4. POPIS STROJE A OBSAH DODÁVKY ................................................................................................................34
Popis stroje (viz Obr. 1) ............................................................................................................................................34
5. INSTALACE OPĚRNÝCH ZUBŮ, VODÍCÍ LIŠTY A ŘETĚZU ........................................................................35
Instalace opěrných zubů (Obr. 2) ....................................................................................................................35
Instalace vodící lišty a řetězu..............................................................................................................................35
6. PALIVO A OLEJ PRO MAZÁNÍ ŘETĚZU ............................................................................................................36
Naplnění nádržky olejem .....................................................................................................................................36
Příprava palivové směsi .........................................................................................................................................36
Skladování paliva......................................................................................................................................................37
7. PŘÍPRAVA NA POUŽITÍ .............................................................................................................................................37
Brzda řetězu (Obr. 1, bod 10) ...............................................................................................................................38
Kontrola funkce brzdy ........................................................................................................................................38
8. SPUŠTĚNÍ A VYPNUTÍ PILY ......................................................................................................................................38
Startování studeného motoru ............................................................................................................................38
Startování zahřátého motoru ..............................................................................................................................39
Regulace otáček ......................................................................................................................................................39
Zastavení motoru .......................................................................................................................................................39
Kontrola mazání řetězu ..........................................................................................................................................39
9. SEŘÍZENÍ NAPNUTÍ ŘETĚZU .................................................................................................................................... 40
CZ
ŘETĚZOVÁ PILA NÁVO D K OBSLUZE
CZ 28
Obsah
10. ŘEZÁNÍ ............................................................................................................................................................................ 40
Bezpečnostní brzda (ochrana proti zpětnému rázu) .......................................................................... 40
Kácení stromu ..............................................................................................................................................................41
Řezání polen ................................................................................................................................................................41
Poleno ležící na zemi ..........................................................................................................................................41
Poleno nad zemí ...................................................................................................................................................42
Odvětvování padlého stromu ...........................................................................................................................42
11. ČIŠTĚNÍ A ÚDRŽBA NÁŘADÍ .................................................................................................................................42
Údržba po každém použití ...................................................................................................................................42
Čištění tělesa řetězové pily ...................................................................................................................................42
Údržba vodicí lišty .....................................................................................................................................................43
Běžná údržby vodicí lišty .......................................................................................................................................43
12. OSTŘENÍ PILOVÉHO ŘETĚZU ................................................................................................................................. 44
Vybavení nezbytné pro ostření pilového řetězu ..................................................................................... 44
Ostření zubů řetězu .................................................................................................................................................. 44
Pilování omezovacího zubu ................................................................................................................................45
13. VÝMĚNA PILOVÉHO ŘETĚZU .................................................................................................................................46
14. TECHNICKÉ PARAMETRY ........................................................................................................................................47
15. ŘEŠENÍ PROBLÉMŮ ....................................................................................................................................................48
16. LIKVIDACE ......................................................................................................................................................................49
17. PROHLÁŠENÍ O SHODĚ ..........................................................................................................................................50
FZP 4 216 B
Všeobecné bezpečnostní předpisy
29
1. VŠEOBECNÉ BEZPEČNOSTNÍ PŘEDPISY
Důležitá bezpečnostní upozornění
Výrobek pečlivě vybalte a dejte pozor, abyste nevyhodili žádnou část obalového materiálu dříve, než
najdete všechny součásti výrobku.
Výrobek uchovávejte na suchém místě mimo dosah dětí.
Čtěte všechna upozorněni a pokyny. Zanedbání při dodržování varovných upozorněni a pokynů mohou mít
za následek úraz elektrickým proudem, požár a/nebo těžká poraněni.
Obal
Výrobek je umístěn v obalu bránícím poškozením při transpor tu. Tento obal je surovinou a lze jej
proto odevzdat k recyklaci.
Návod k použití
Než začnete se strojem pracovat, přečtěte si následující bezpečnostní předpisy a pokyny k používání.
Seznamte se s obslužnými prvky a správným používáním zařízení. Návod pečlivě uschovejte pro případ
pozdější potřeby. Minimálně po dobu záruky doporučujeme uschovat originální obal včetně vnitřního balícího
materiálu, pokladní doklad a záruční list.
V případě přepravy zabalte stroj zpět do originální krabice od výrobce, zajistíte si tak maximální ochranu
výrobku při případném transportu (např. stěhování nebo odeslání do servisního střediska).
POZNÁMKA: Předáváte-li stroj dalším osobám, předejte jej společně s návodem.
Dodržování přiloženého návodu k obsluze je předpokladem řádného používáni stroje. Návod k obsluze
obsahuje rovněž pokyny pro obsluhu, údržbu a opravy.
CZ
Výrobce nepřebírá odpovědnost za nehody nebo škody vzniklé následkem
nedodržování tohoto návodu.
ŘETĚZOVÁ PILA NÁVO D K OBSLUZE
CZ 30
Vysvětlení štítků spokyny na stroji
2. VYSVĚTLENÍ ŠTÍTKŮ S POKYNY NA STROJI
Před použitím stroje si pozorně přečtěte
návod k obsluze.
Při obsluze stroje noste ochranné
pomůcky jako ochranné brýle, sluchátka
apod.
Při obsluze řetězové pily používejte vždy
obě ruce.
Při práci používejte ochranné rukavice.
Používejte pevnou izolační pracovní obuv.
Pozor! Nebezpečí zpětného rázu
Varování! Pozor!
FZP 4 216 B
Loading...