Fetco ITD-2135 Installation Manual

FETCO ITD-2135 3 gallon Ice Tea Dispenser
Instructions for use
-Remove dispenser cover before brewing, replace cover after brew is complete
-To prevent overflow, make sure the dispenser is completely empty before brewing into it.
-Never keep tea overnight in this or any dispenser.
-Use only the handles to lift or carry the dispenser
Cleaning Instructions
Do not use bleach or cleaners containing chlorides. Use any commercial beverage urn cleaner to clean the inside of the dispenser. Follow the cleaner manufacturer’s instructions. Thoroughly rinse the dispenser after cleaning. Remove faucet body from shank by unscrewing plastic wing nut as shown Disassemble upper assembly and remove the faucet upper assembly as shown Inspect the seat cup for wear. Clean or replace if necessary. Wash plastic parts with cleaning brush and dish detergent. Avoid abrasives
To sanitize the dispenser before filling, brew a batch of water only (no tea) into the dispenser allow it to rest for 10 minutes-and drain. Repeat daily, or as needed.
Product D-064
Å Faucet Shank
-Unscrew and remove faucet body.
-With cleaner or hot soapy water--use brush to clean faucet shank.
-Do not allow sharp bush tip to contact the soft set cup.
-Rinse and Dry
We recommend Urnex Tabz Tea Clean for use on FETCO® tea brewing equipment
-Specifically formulated for the removal of tea stains from tea brewing equipment.
-Daily cleaning of Iced Tea Dispensers ensures fresh tasting iced tea and properly maintained equipment.
-Cleans brew basket and serving vessel in one simple step
-Sanitizes all types of tea ware for bright and sparkling flavor of brewed tea
-Unscrew and remove
-Clean faucet body and upper assembly by soaking in commercial dispenser cleaner or hot soapy water.
-Rinse and Dry
Simple directions to use Urnex Tabz™
1 Drain all product from dispenser
2. Place four tablets in center of brew basket
3. Run brew cycle into server and hold.
4. Discard solution and remove any residue.
5. Rinse all parts with clean water. REPEAT
19
Optional tea dispenser instructions and cleaning
Location of dispenser trim
Drawing number1102.00193.00
FETCO ITD-2135 3 gallon Ice Tea Dispenser Product D-064
Ref. QTY
1 1 1111.00034.00 WELDMENT, DISPENSER 3.5GAL, TBS-2121
2 1 1023.00187.00 PROTECTOR, BACK POCKET, TBS DISP.
3 1 1012.00005.00 SHANK,TEA DISPENSER FAUCET
4 1 1024.00061.00 O_RING SHANK 1/2 ID X 5/8 OD, TBS DISP.
5 1 1023.00186.00 GASKET, TEA CONTAINER FAUCET SHANK
6 1 1013.00078.00 SCREW, SHANK TEA DISPENSER
7 1 1071.00045.00 C - RING FOR TEA FAUCET
8 1 1071.00047.00 FAUCET, TEA DISPENSER
9 1 1071.00046.00 PLASTIC WING NUT
10 4 1023.00175.00 BUMPER DISPENSER 2A
11 4 1023.00174.00 BUMPER DISPENSER 2B
12 4 1082.00075.00 SCREW, #8 X 1/2", FLAT HD, PH, SHEET METAL
13 1 1023.00178.00 DISPENSER COVER, TBS-2121
NOT
SHOWN
Designs, materials, specifications, physical dimensions, firmware and software protocol for equipment or replacement parts are subject to change by FETCO without notice
1 1074.00005.00 CLEANING BRUSH--Ice Tea Dispenser
PART NO DESCRIPTION
20
Loading...