Ferroli F30 Installation Instructions Manual

Supplied By www.heating spares.co Tel. [phone]

FERROLI F30

Gas Combination Boiler for Central Heating

and Hot Water Production, Wall Mounted,

Copper Heat Exchanger, Fan Assisted,

Room Sealed,

Electronic Flame Ignition and Control

REAR FLUE INSTALLATION

Appr. nr. B99.06 A - CE 0461 BM 0607

INSTRUCTIONS

G.C. NO: 47-267-32

3544016/0 - JDL 10/04

Supplied By www.heating spares.co Tel. [phone]

FERROLI F30

For installation (back flue connection):

For direct back flue connection it is necessary to use the optional kit Part No 822186, and it is necessary to alter

the fan direction inside the boiler.
Please Follow the below procedure carefully:

Remove fan by pulling off electri­cal connections. Pull off air pres­sure switch tubes from the air
pressure switch remove 2 screws
b. Rotate the fan downward to
disengage it from the securing
pin (a).

Fig. 21a

Remove the four screws which fix
the back plate onto sealed cham­ber, remove and rotate the plate
through 90° and fit it to the top of
the boiler to cover the original flue
outlet. Secure it in place with the
four screws removed previously.
(fig 21b 21c)
Attach the flue adaptor (A) to the
rear of the appliance using the
ring seal and four screws supplied
(fig 21d)

Remove and disgard the fan adaptor and heat­shield

Fig. 21b

Fig. 21c

Fig. 21d

Remove fan mounting plate by undoing the three fixing screws "d". Rotate the fan through 90° so that the fan
nozzle points sideways. Secure the fan to the plate in the new position using screws in position "c".
Attach the fan spigot adapter "B" using the two screws "E" provided.
NOTE: The spigot must be sealed using high temperature silicone, not supplied.

E

Fig. 21e

Fig. 21f

Fig. 21g

Page 1

Supplied By www.heating spares.co Tel. [phone]

Back flue outlet (Diagram 1-9)

FERROLI F30

1. Core drill 127mm hole (5").

Fig. 22a

6. Cut the outer flue 80mm longer
than the inner wall finish.

Fig. 22f

2. Push through the outer flue.

Fig. 22b Fig. 22c

7. Insert the aluminium flue pipe into
white plastic outer flue, making
sure the aluminium pipe sits fully
and centrally into the flue termi­nal. Mark the aluminium flue pipe
at the point it is flush with the
plastic outer flue, add 60mm to
this mark and cut the aluminium
inner flue pipe at this point.

NOTE: Ensure the end is cut square

de-burred & lubricated with sili­cone grease.

3. Gently pull back until wall seal
is flush with the wall.

60mm60mm

Fig. 22g

8. Ensure that the inner metal flue is pushed into the
terminal, as shown.

9. Lift boiler onto the wall bracket with flue in place,
and engage the outer flue into the adapter. Secure
the boiler using the nuts & washers supplied.

60mm

Fig. 22h Fig. 22i

9. Make sure the inner flue is fully engaged in the
flue terminal, Re-attach the fan as shown in fig
21h. Secure bottom of boiler using two screws
and washers provided.

Page 2

Supplied By www.heating spares.co Tel. [phone]

FERROLI F30

Re-attach the fan with the screws (b). Refit wiring connections to fan and air pressure switch tubes ensuring
correct orientation. I.E. red tube to air pressure switch connection with red dot (+) and clear tube to air pressure
switch connection with no paint marking (-). (Clear hose to fan venturi)
Fit the fan into the boiler rotating the front to engage with the mountin lug. Secure with the screws b.

NOTE

Mounting plate rests

on lower lug.

Air pickup Venturi

NOTE: The rear flue application does NOT require any flue restrictor ring to be installed. The maximum flue
distance for this application is 1 meter with NO bends being permissible.
When testing the appliance, if the boiler does not ignite, but the fan runs continuously, then it woul be advisa­ble to check the orientation of the air pressure switch hoses.

Fig. 21h

FOR FURTHER INFORMATION PLEASE CALL OUR INSTALLER TECHNICAL

HELP LINE

TEL O8707 282885 OPTION 1

Page 3