Ferm FZT-250N User Manual
Ferm • P.O. Box 134 • 8280 AC Genemuiden-NL • Web: www.ferm.nl 0208/28
Ferm Saw Bench
FZT-250N
USER’S MANUAL
Art.nr. 720120
Screwfix art.nr: 97825
UK Subject to change
Ferm 11
Saw Bench
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
Electrical safety
Warning! When using electric tools, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and personal injury. Read
all these instructions before attempting to operate
this product and save these instructions.
Always check that the voltage corresponds to the
voltage on the rating plate.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm2. When using a cable reel always unwind
the reel completely.
GENERAL SAFETY INSTRUCTIONS
Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instructions before attempting to operate this product.
Retain for future refence.
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Keep work
area well lit. Do not use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock.
Prevent body contact with grounded surfaces (e.g.
pipes, radiators, refrigerators).
4. Keep children away.
Children should be kept away from the work area at
all times. Do not let children handle the Electric
Rotary Hammer Drill at any time.
5. Store unused tools.
When not is use keep tools out of reach of children.
Store in a dry and secure location.
6. Do not force tool.
Do not apply undue pressure as this may affect performance and may cause damage to the machine.
Forcing the job also increases the potential for accidents.
7. Use right tool.
Do not force small tools or attachments to do the job
of heavy duty tool. Do not use a Angle Grinder for
purposes not intended.
8. Dress properly.
Do not wear loose clothing or Jewellery. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working outdoors. Wear protective hair covering to contain long
hair.
9. Use safety glasses.
Also use face or dust mask if cutting operation is
dusty.
10.Do not abuse cord.
Never carry tool by cord or yank it to disconnect it
from electrical socket. Keep cord from heat, oil and
sharp edges.
11.Secure work.
Use clamps or a vice to hold work. It’s safer than using
your hand and it frees both hands to operate tool.
12.Do not overreach.
Keep proper footing and balance at all times.
13.Maintain tools with care.
Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and, if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free
from oil and grease.
14.Disconnect tools.
When not in use, before servicing, and when changing accessories such as blades, bits and cutters.
15.Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
16.Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch.
Be sure switch is off when plugging in.
17.Outdoor use extension cords.
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
Always use tool in conjunction with a residual circuit
breaker device.
18.Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
19.Check damaged parts.
Before further use of the tool, a guard or other part
UK
English
2 Ferm
EXPLODED VIEW
Loading...