Ferm FWS-150K Instructions For Use Manual

0310-03

INSTRUCTIONS FOR USE

WALL SLOTTER

FWS-150K

ART.NR. 719810

Overheating

- The ventilation slots are blocked with dirt.Clean with
dry cloth.

- The machine does not start when switched on. Check
the mains lead and the fuse/plug.Take to your Ferm
Dealer for repair

- The motor is defective.Take to your Ferm Dealer.

MAINTAIN TOOLS WITH CARE

Keep the tool clean for better and safer performance.
Store the discs properly in accordance with the maker’s
instructions.

Follow instructions for changing accessories.Inspect tool
and extension cables periodically and if damaged, have
them repaired by a qualified person or authorised service
body.Keep handles free from oil or grease. Keep the venti­lation slots clean to prevent motor overheating.

Check for damaged parts

Do not use a tool with damaged parts,before further use a
damaged tool must be carefully checked by a qualified per­son to determine that it will operate properly.Check for
alignment of moving parts, binding or breakage of parts,
mounting and other conditions that may affect its opera­tion.
A damaged part or guard should be properly repaired by
an authorised service centre, unless indicated otherwise
in the instruction manual.Have defective switches repla­ced by an authorised service centre. Do not use a tool if
the switch does not turn on and off.

Have your tool repaired by an expert

This appliance is manufactured in accordance with rele­vant safety standards.Only experts must carry out repai­ring of electrical appliances,otherwise considerable dan­ger for the user may result.

Storing tools

When not in use tools should be stored in the dry,out of
reach of children.

ELECTRICAL INFORMATION

This product is complete with a pre-wired mains plug,it is
double insulated in accordance with EN 50144 – no earth
wire is required

If the plug needs replacing follow these instructions.

Wire correctly

The wires in the mains lead are coloured in the following
way:

BLUE -Neutral
BROWN -Live

Securing wires

Secure wires carefully and firmly to the correct terminals.
Secure the mains cable in the plug cord grip firmly.
Fit a 13-amp fuse. If a 13amp (BS1363) plug is used a (BS

1362) ASTA approved 13-amp fuse must be fitted.

Recycle/Dispose of old plug and cable

Prevent inadvertent connection to socket and risk of elec­tric shock.

ENVIRONMENT

Recycle the packaging according to the identification
marks on it.
At the end of the product or its accessories life please re­cycle where facilities exist - phone the Helpline for cur­rent advice on recycling.

Helpline

For any questions relating to operational or safety
matters contact:

Ferm Customer Helpline on:0115 966 1199
Monday-Friday 8am – 6pm
Saturday 9am – 1 pm

GUARANTEE

The guarantee conditions can be found on the separately
enclosed guarantee card.

We declare under our sole responsibility that this

product is in conformity with the following

standards or standardized documents

EN-50144-1,prEN50144-2-3,

EN-55014-1,EN-55014-2,

EN61000-3-2,EN61000-3-3,

in accordance with the regulations:

98/37/EEC
73/23/EEC

89/336/EEC

from 01-12-2001

GENEMUIDEN NL

W. Kamphof
Quality department

CE

ı

DECLARATION OF CONFORMITY

(UK)

Blue

(Neutral)

Green & Yellow

(Earth)

Brown

(Live)

Fuse

(13 Amp)

Wall chaser FWS-150K

152

Wall chaser FWS-150K

GENERAL

Congratulations!

With the purchase of this high quality Ferm tool, you
have made an excellent choice. Ferm products are
rugged, safe and easy to use.

It is very important to exercise care when handling
and servicing this tool. Please read these instructions
thoroughly, and be sure to follow the directions given.
You will then enjoy many years of service from your
Ferm tool.

Package contents

• Electric wall chaser

• Handgrip

• Diamond cutting discs (2 x)

• Cam wrench

• Hex key

• Cold chisel

• Dust extraction adapter

• Set carbon brushes

• Instructions for use

• Guarantee card

Product information

Safety Instructions

In these instructions for use, the following symbols
are used:

Caution: risk of bodily harm, fatality or da­mage to the machine, from failure to follow
the directions in these instructions for use.

Caution: electrical current.

The machine is double insulated compliant
with EN50144; therefore no earth connecti­on is required.

Visual check before starting to work

Specifications

Voltage 230 V~

Frequency 50 Hz

Power rating 1450 W

Rotational speed (not loaded)

8500/min

Max.cutting depth 8-40 mm

Max.channel width 8-30 mm

Weight 4,5 kg

Cutting disc (2x) Ø150 x 22,2 x 2,0

Lpa (Sound pressure level) 94,9 dB(A)

Lwa (Sound power level) 107,9 dB(A)

Vibration level 0,9 m/s

2

1. On/off trigger switch

2. Attachment point for
handgrip

3. Connection for

mechanical dust

extraction

4. Guide wheel

5. Distance washers

6. Spindle nut

7. Cutting depth fixing
knob

8. Cutting direction

9. Shaft lock

MAITENANCE AND REPAIR

Overview spare parts

1

2

11

10

12

9

3

4

5

6

8

30

31

7

13

28

40

41

24

29

35

16

17

15

14

22

23

18

19

20

26

32

27

33

33

34

25

37

38

39

36

21

MAINTENCE,CARE AND
REPAIR

Switch off and unplug the machine before carrying
out any cleaning or maintenance work.

CLEANING

Do not use flammable liquids to clean the angle grinder,

FAULTS
Switch OFF immediately at the mains plug and
remove the plug when:

- The plug or cable is damaged.

- The switch on the machine is defective.

-You smell or see smoke caused by scorched insulation
in the machine.

GENERAL SAFETY INSTRUCTIONS

Wall chaser FWS-150K

14

Wall chaser FWS-150K

3

Caution!

Whenever working with electric tools, always take
basic safety precautions including those described
below, to reduce the risk of fire, electric shock, and
personal injury.
Before using the product, read all safe use directions
and keep them in a handy place.

Directions for safe use:

1 Keep the working environment tidy

• Untidy workplaces and benches can easily cause
accidents.

2 Be alert to the conditions in your surroundings.

• Do not expose electric tools to rainwater.

•Never use electric tools in damp or wet condi­tions.

• Ensure that the work area is well lit.

•Never use electric tools where there is a hazard of
combustion or explosion.

3 Protect yourself from electric shock

•Avoid bodily contact with earthed surfaces (such
as pipes, radiators, heaters, refrigerators).

4 Keep children at a safe distance

• Do not allow bystanders to touch the tool or ex­tension cord.

• Do not allow bystanders access to the worksite.

5 Store tools, which are not in use

• Store tools, which are not in use, in a dry, high, or
lockable place, beyond the reach of children.

6 Do not overload the tool

• For a good and safe result, use the tool settings
advised.

7 Use the right tool for the job

• Do not use light tools or accessories for heavy du­ty jobs.

• Never use the tool for work it was not designed to
do. For example, do not use a circular saw to saw
branches or cut down trees.

8 Wear suitable work clothing

•Wear no loose clothing or jewellery, as these
could become entangled in moving parts of the
machine.

• When working outdoors, rubber gloves and foot­wear with heavy profile soles are recommended.

•Wear a headband or hairnet to keep long hair out
of the danger zone.

9 Wear safety glasses

• When your work generates dust, wear a dustmask
or facemask.

10 Connect a dust extraction system

• If the tool provides for connection to a dust
extraction system, ensure that this is connected
and working correctly.

11 Only use the power cord for its intended use

• Never carry the tool by its power cord, and do not
unplug the tool from the power by pulling on the
power cord.

•Protect the power cord from heat, oil, and/or
sharp edges.

12 Do not overextend yourself

• Ensure you have secure footing, and maintain
your balance at all times.

13 Maintain the tool with care

• Keep cutting equipment sharp and clean, so you
will achieve a good result, safely.

• Follow the directions for lubrication and replace­ment of parts.

• Inspect the power cord regularly and have a da­maged cord repaired by an authorised service
agent.

• Inspect extension cords regularly, and replace
any damaged cords.

•Keep handgrips dry, clean and free from grease
and oil.

14 Remove the plug from the wall socket

•Whenever the tool is not in use, and before ex­changing parts such as blades, bits and knives.

GENERAL SAFETY INSTRUCTIONS

1. Maintain the tool with care.

• Keep the tool clean and sharp.

• Follow the directions for lubrication and fitting of
accessories.

• Periodically inspect the power cord, and have any
damage repaired by an authorised service agent.

• Periodically inspect extension cords, and replace
them if damaged.

• Keep handgrips dry, clean and free from grease
and oil.

2. Always remove the plug from the mains, whene­ver:

• the machine is not in use;

• you service the machine;

• exchanging accessories such as blades.

3. Immediately repair any damage.
Regularly inspect all moving parts, attachments
and all other parts that can affect correct opera­tion.

• Have all repair work carried out by an authorised
service agent.

MAITENANCE AND REPAIR

MAITENANCE AND REPAIR

Malfunctions

Problem

The electric motor becomes hot
and cuts out.

The machine switched will not
run.

Cutting is difficult and the channel
made is irregular.
When cutting, the workpiece be­gins to vibrate heavily
The machine runs erratically
and/or noisily.

Possible cause

The overheating protection has been
activated.

The motor is defective.

The overload protection has been acti­vated.
The overheating protection has been
activated.

The switch is damaged.

The cutting discs are bent or blunt.

The cutting discs are overheated or de­formed.
The carbon brushes are worn.

Solution

Wait several minutes until the machi­ne has cooled down, then re-start the
machine.
Take the machine to your Ferm dealer
for inspection and/or repair
Re-start the machine.

Wait several minutes until the machi­ne has cooled down, and then re­start the machine.
Take the machine to your Ferm dealer
for inspection and/or repair
Replace the cutting discs.

Replace the cutting discs.

Take the machine to your Ferm dealer
for replacement of the carbon brush­es.