
12
LEDs
5 6
4
3
2
1
TONE BLOOM
LEVEL
THE PELT
9V DC
INPUT
SOFT HARD
MID THICK
13
7
FUZZ
8
9
10
11
1. Footswitch
2. Jewel Indicator
3. Output Jack
4. Level
5. Tone
6. Bloom
7. Fuzz
8. Thick Switch
9. Mid Switch
10. Input Jack
11. Low Battery Indicator
12. LED Kill Switch
13. DC Power Connector

THE PELT
Thanks for purchasing The Pelt — a flexible fuzz pedal with
a wide range of saturated sounds. Driven by silicon
transistors, this pedal ranges from full on wall of fuzz to
smooth, harmonically rich drive. Midrange boost and
thickness toggles work to help find the perfect textures for
your sound.
DESIGNED IN CALIFORNIA, U.S.A.

Level
This control adjusts your output level when the fuzz is engaged.
Tone
This controls the high frequencies present in your signal. Use it like a
tone control on your guitar or bass--keep it all the way up for the full
frequency range of your instrument or roll it back to mellow out the
treble.
Bloom
This controls the attack of the fuzz effect. As the control sweeps from
Soft to Hard, the fuzz signal changes from smoother, violin like attack
to abrupt and splattered saturation.
Fuzz
This controls the pedal’s fuzz level. Add more saturation by rotating
the control clockwise.
Thick Switch
This switch allows more of your bass frequencies through the circuit to
fatten up your fuzz tone.
Mid Switch
This three-position switch shapes your instrument’s midrange by
boosting or cutting mids to contour your punch and presence. Leave
the switch in the middle position to keep your midrange unaffected.
Jewel Indicator
The Jewel Indicator shows when the fuzz effect is active.
Footswitch
This rugged footswitch bypasses the fuzz.

Input Jack
This is a high-impedance input suitable for electric guitar, bass,
keyboards and other instruments.
Output Jack
This is a low-impedance output jack that connects to the amp or to
the next effect pedal in the signal chain.
DC Power Connector
This is a standard, center-negative 9VDC jack for use with
appropriate power supplies.
LED Kill Switch
This switch extinguishes the LEDs that illuminate the knobs—useful in
maximizing battery life when running the pedal from batteries.
Low Battery Indicator
This red LED on the front of the battery door illuminates when battery
voltage drops below a set threshold, indicating that the battery
should be replaced soon.

FENDER MUSICAL INSTRUMENTS CORPORATION
A PRODUCT OF:
CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC.
Copyright © 2018 FMIC. All rights reserved.
P/N 7714182000 - REV A
Important Safety Instructions
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC
power to rain or moisture.
•Do not alter the AC plug of the connected power adapter
•Do not drip or splash liquids on the unit.
•No user serviceable parts inside, refer servicing to qualified personnel only.
• WARNING: The unit must only be connected to a safety agency certified, regulated,
power source (adapter), approved for useand compliant with applicable local and
national regulatory safety requirements.
• Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth
for cleaning and then wait until the unit is completely dry before reconnecting it to power.
• Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable
of producing very high sound pressure levels which may cause temporary or permanent
hearing damage. Use care when setting and adjusting volume levels during use.
Languages
Manual available in Espanol, francais, Italiano, Deutch, Portugues, (Chinese)
www.fender.com/support
Specifications
IMPEDANCES:
POWER SUPPLY:
POWER REQUIREMENTS:
DIMENSIONS:
WEIGHT:
Product specifications subject to change without notice
INPUT: 500kΩ OUTPUT LOAD: >10kΩ
One 9V battery or 9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
30mA @ 9VDC
50mA, knob LEDs on
2.75” x 4.9” x 2.5” (95.25mm x 124.5mm x 63.5mm)
.9lbs (.40kg)

© FENDER MUSICAL INSTRUMENTS 2018