Fender ion600 reissue full schematic

SERVICE MANUAL

Champion 600
(This is the model name for warranty claims)
p/n 233-0100-000 (120V)
ATTENTION:
WARRANTY SERVICE PROCEDURES
The Champion 600 Amplifier is not available for warranty field service. However; any Champion 600 that is presented for warranty service should be tested for bad tubes. If the defect is due to a failed tube, and the tube warranty has expired, the consumer/dealer will be responsible for tube replacement costs. If the tube warranty has not expired contact FMIC Customer Service for replacement tubes. If the defect is not tube related please contact FMIC Customer Service to arrange for a replacement amplifier.
Fender Musical Instruments Corporation, 8860 East Chaparral Road Suite 100 Scottsdale, AZ 85250
Issued: October, 2006
2
Champion™ 600
(This is the model name for warranty claims)
June, 2007
IMPORTANT NOTICE
Copyright © 2006 FMIC. All rights reserved. All information contained herein is CONFIDENTIAL and PROPRIETARY and is the property of Fender® Musical Instruments Corporation. It is not to be sold or assigned to another party and is disclosed solely for use by Fender Authorized Service Centers for purposes of product service and maintenance. All information is not to be dis­closed to others without the expressed permission of Fender® Musical Instruments Corporation. All

PARTS LIST CODES

The description codes used in the itemized Parts Lists are defined below:
CAPACITOR
CAP AE = Aluminum Electrolytic CAP CA = Ceramic Axial CAP CD = Ceramic Disk CAP CR = Ceramic Radial CAP MPF = Metalized Polyester Film CAP MY = Mylar CAP PFF = Polyester Film/Foil
RESISTOR
RES CC = Carbon Comp RES CF = Carbon Film RES FP = Flame Proof RES MF = Metal Film RES MOX = Metal Oxide RES WW = Wire Wound
CODES
CODES
specifications are subject to change without no­tice. This information and any copies produced electronically or otherwise must be surrendered upon demand of Fender® Musical Instruments Corporation.
Parts marked with two asterisks ( required use of that specific part. This is neces­sary for RELIABILITY and SAFETY requirements.
DO NOT USE A SUBSTITUTE!
HARDWARE
BLX = Black Oxide CR = Chrome Plated HWH = Hex Washer Head M = Machine Screw NI = Nickel Plated OHP = Oval Head Phillips PB = Particle Board PHP = Pan Head Phillips PHPS = Pan Head Phillips Sems SMA = Sheet Metal "A" Point SMB = Sheet Metal "B" Point SS = Stainless Steel TF = Thread Forming ZI = Zinc Plated
CODES
**) indicate the
Champion™ 600
(This is the model name for warranty claims)

SPECIFICATIONS

Model Name: Champion 600
Release Number: PR 722
Part Numbers CHAMPION 600 120V 233-0100-000 CHAMPION 600 120V DS 233-0100-900 CHAMPION 600 110V TW DS 233-0101-900 CHAMPION 600 240V AUS DS 233-0103-900 CHAMPION 600 230V UK DS 233-0104-900 CHAMPION 600 230V ARG DS 233-0105-900 CHAMPION 600 230V EUR DS 233-0106-900 CHAMPION 600 100V JPN DS 233-0107-900 CHAMPION 600 220V ROK DS 233-0109-900
Power Requirement: 25 W
Fuses: F 1A, 250V for 100V versions
F 1A, 250V for 120V versions F 500mA, 250V for 240V versions
F 500 mA, 250V for 230V versions
Input Sensitivity: 25 mV (volume at maximum for full power
Power Output: 5W RMS into 4 ohms @ < 5%THD, 1000Hz
Impedances Input: >1M Ohms
Speaker Complement: 6” , 4 ohm
Dimensions Height: 11 in (28 cm) Width: 12 in (12 cm) Depth: 7.5 in (19 cm)
Weight: 15 lbs (7 kg)
Product specifications are subject to change without notice
3
Loading...
+ 5 hidden pages