Fender 215-PRO Operation Manual

(This is the model name for warranty claims)

SERVICE MANUAL

215 PRO

p/n 2215200000 (120V)

ATTENTION:

WARRANTY SERVICE PROCEDURES

The Fender 215 PRO is covered by the standard FMIC 5 Year Electronic Limited Warranty as it
applies to Speaker Enclosures. PCB Assemblies and Electronic Components are covered for 5
years. Speakers, Drivers, Cabinet Assemblies, and Cabinet Hardware are covered for 1 year.
Cables and wiring harnesses for 90 days. This enclosure is considered to be repairable to the
component level in the field. If you have questions please contact the FMIC Customer Service
Support Center at [phone] or Email [e-mail]

Fender Musical Instruments Corporation, 8860 East Chaparral Road Suite 100 Scottsdale, AZ 85250

Issued: September, 2007

2

215 PRO

(This is the model name for warranty claims)

September, 2007

IMPORTANT NOTICE

• Copyright © 2007 FMIC. All rights reserved. All
information contained herein is CONFIDENTIAL
and PROPRIETARY and is the property of
Fender® Musical Instruments Corporation. It is
not to be sold or assigned to another party and is
disclosed solely for use by Fender Authorized
Service Centers for purposes of product service
and maintenance. All information is not to be dis­closed to others without the expressed permission
of Fender® Musical Instruments Corporation. All

PARTS LIST CODES

The description codes used in the itemized Parts Lists are defined below:

CAPACITOR

CAP AE = Aluminum Electrolytic
CAP CA = Ceramic Axial
CAP CD = Ceramic Disk
CAP CR = Ceramic Radial
CAP MPF = Metalized Polyester Film
CAP MY = Mylar
CAP PFF = Polyester Film/Foil

RESISTOR

RES CC = Carbon Comp
RES CF = Carbon Film
RES FP = Flame Proof
RES MF = Metal Film
RES MOX = Metal Oxide
RES WW = Wire Wound

CODES

CODES

specifications are subject to change without no­tice. This information and any copies produced
electronically or otherwise must be surrendered
upon demand of Fender® Musical Instruments
Corporation.

• Parts marked with two asterisks (
required use of that specific part. This is neces­sary for RELIABILITY and SAFETY requirements.

DO NOT USE A SUBSTITUTE!

HARDWARE

BLX = Black Oxide
CR = Chrome Plated
HWH = Hex Washer Head
M = Machine Screw
NI = Nickel Plated
OHP = Oval Head Phillips
PB = Particle Board
PHP = Pan Head Phillips
PHPS = Pan Head Phillips Sems
SMA = Sheet Metal "A" Point
SMB = Sheet Metal "B" Point
SS = Stainless Steel
TF = Thread Forming
ZI = Zinc Plated

CODES

**) indicate the

215 PRO

(This is the model name for warranty claims)

SPECIFICATIONS

Model Name: 215 PRO

Release Number: PR 730

Part Number: 2215200000

Impedance: 4 ohms

Sensitivity: 101 dB, 1w-1m

Power Handling: 800 Watts, Continuous

1600 Watts, Program

Drivers: Two 15” (38.1 cm) Fender Special Design cast frame woofers with
3” (7.6 cm) voice coil and 105 0z. (2.98 kg) magnet (p/n 0075912000)

One horn tweeter with 1” (2.5 cm) voice coil and 8 oz. (0.23 kg) magnet
(p/n 0048847000)

Connections: Dual, parallel wired, ¼” (6.35 mm) high current input jacks and Speakon
connector

Cabinet: ¾” (1.9 cm) Baltic Birch plywood

Dimensions Height: 36 5/8 in (93.0 cm)
Width: 26 in (66.0 cm)
Depth: 17 in (43.2 cm)

Weight: 110 lb (50.0 kg)

Product specifications are subject to change without notice

3

SERVICE NOTES

Input Assembly removal is required for lamp re­placement and is accomplished by following these
steps:

1. Remove the four screws from the input panel
corners.

2. Pull the panel out at the top until the L-pad is
clear of the mounting plate, then pull upward on
the assembly.

215 PRO

(This is the model name for warranty claims)

3. Use a small screwdriver or other tool to remove
the blown lamp, which is visible through a cut­out in the circuit board.

4. Remove the spare lamp stowed on the side of
the circuit board and install it where the blown
lamp was removed.

5. Install the input assembly in the reverse order
of removal.

4

PCB EXCHANGE POLICY

Parts marked with a single asterisk (
Lists are not field replaceable. If a failure due to
one of these components is detected, please con­tact the FMIC Customer Service Department to
order the complete PCB Assembly.

*) in the Part