Fantini Cosmi Intellitherm C75, Intellitherm Techno W C55 User Manual
ADVANCED FUNCTIONS
MONITORING HOW MANY HOURS THE HEATING STAYS ON
C75
Move the switch S to the. position
1
S
Move the switch P to the PROG position
2
P
Read the hours of heating on the previous day
3
Read the hours of heating since the controller was
4
enabled.
MINIMUM AND MAXIMUM ROOM TEMPERATURE ON THE PREVIOUS DAY
With Intellitherm C75 you can also keep a check on the
minimum and maximum temperatures recorded in the room
on the previous day and the time when they occurred.
Move the switch S to the (economy) position
S
for the MINIMUM temperature or to the
1
comfort) position for the MAXIMUM
temperature
P
Move the switch P to the PROG position
2
Read the minimum or maximum room temperature
3
Read the time when said minimum or maximum temperature was
4
recorded
SUMMER - AIR CONDITIONING OPERATION
When you move the switch I to the SUMMER position, Intellitherm
switches to operating the AIR CONDITIONING system. The red knob is used for
adjusting the comfort mode temperature required in the room, while the economy
I
and antifreeze modes are disabled.
The red sectors on the ring appearing on the display consequently indicate the
hours when the air-conditioning system is in operation, while the sectors in any
other color indicate when it is off.
TECHNICAL FEATURES
- In compliance with the CEI EN 60730-1 and parts two
- Terminal carrying capacity 8 (5) A 250 Vac
- Micro-disconnection (1BU)
- No-load switching contact
- Temperature control:
- Comfort from 2 to 62 °C
- Economy from 2 to 62 °C
- Differential ± 0.25 °C
- Reference thermal gradient 4° K/h
- OFF mode with optional antifreeze protection (5 °C)
Selected by means of a dip switch
- double insulation
We reserve the right to make any technical and structural changes deemed necessary without prior notice.
- Protection grade IP 20 (normal pollution)
- Powered by 2 alkaline AA 1.5V pencil batteries, with
no connection to the mains
- Battery life two years approx.
- Automatic monitoring of battery charge with signal on
display when battery is low
- Battery changing without losing previouslymemorized programs
- Switch for summer/winter operating modes
- Reset button for restoring standard program
-Overall dimensions: 120 x 80 x 27 mm
C75
C55
2004/03
WEEKLY TEMPERATURE CONTROLLER
1 - WALL MOUNTING
Intellitherm C75 is supplied complete with a base
suitable for mounting flush in a rectangular threemodule or a round outlet box, or for attaching to the
wall.
Fit the controller 1.5 m above floor level, well away
from kitchens, sources of heat, doors or windows.
Make sure that the base is attached on a level and
without any straining.
2 - ELECTRIC CONNECTIONS
Connect terminals 1 - 2 to the heating system with
two wires, replacing the conventional thermostat at
any time, without adding any further connections.
When the room temperature increases, the relay
opens terminals 1 - 2 and closes 1 - 4 .
Terminal 4 is free and can be used for signals or
other purposes.
SELECTING THE OFF MODE
3 -
During periods when it is
to maintain a temperature setting of 5 °C to protect
the system from the risk of freezing.
If you require such
position the dip switch (situated at the bottom lefthand side on the back of the body of the C55) on
HIGH. If, on the other hand, you want the system to
be switched OFF completely, position the dip switch
on LOW.
This selection must be made at the time of
installation and before fitting the batteries.
NOTE: if, at any time after installation, you wish
to change this selection, the Intellitherm must be
reset and reprogrammed.
FITTING THE BODY OF THE TEMPERATURE
4 -
CONTROLLER ON THE BASE
FITTING THE BATTERIES
5 -
Insert two good-quality, alkaline long-life AA 1.5 V
pencil batteries in the space provided, taking care to
comply with the polarity indicated. The batteries can
last about two years; when they begin to run down,
the battery symbol on the display starts to flash
If the batteries are not changed within 15 days,
Intellitherm C55 will automatically switch off and only
the word OFF will appear on the display.
Intellitherm can be set
OFF,
ANTIFREEZE
protection,
Via dell'Osio, 6 20090 Caleppio di Settala MI
International calls Tel.++39 02 95682222
DISTANCE BETWEEN CENTERS FOR FIXING
THE BASE
60 mm
B -
A -
83,5 mm
TERMINAL BOARD AND CONNECTIONS
2
1
4
SELECTING THE OFF OR OFF+ANTIFREEZE
PROTECTION MODES
FITTING AND CHANGING THE BATTERIES
Lift the cover and fit two 1.5V batteries
Fax.++39 02 95307006
E-mail: export@fantinicosmi.it
Http//www.fantinicosmi.it
A= for rectangular
flush-mounted boxes
type 503 (three modules)
B= for round flushmounted boxes
LOOSEN THIS
SCREW AND TURN
THE BODY OF THE
CONTROLLER
UPWARDS TO
DETACH THE BASE
FOR FIXING TO THE
WALL.
4 1 2
ANTIFREEZ (5°C)
OFF
THE DISPLAY Intellitherm C75
At all times, the display shows the room temperature, the actual time of day
and day of week, whether there is any demand for heating (or for
2
24
24
22
22
20
20
18
18
16
16
14
14
4
4
C
C
6
6
DAY
DAY
8
8
12
12
10
10
also shows a programming ring that represents a 24-hour clock, divided into
48 sectors, each corresponding to half an hour. Each sector is further divided
in half and colored red, red-and-black, or black (depending on the program
selected). The color of the sectors indicates the type of temperature
programmed for that particular time of day, i.e.
- red = comfort temperature
2
conditioning in summer) and the battery low signal . The display
- half red and half black = economy temperature
- black = off.
USING INTELLITHERM C55 WITH THE STANDARD PROGRAMS
i.e. with the default schedules and temperatures already programmed at the factory
After installing and wiring up the C55, simply follow the numbered steps specified below.
Move the switch S to the AUTO position for operation with the automatic standard weekly
1
program with the default schedules and temperatures already programmed at the factory.
From Monday (Day 1) to Friday (Day 5)from Saturday (Day 6) to Sunday (Day 7)
°C
20
17
5
OFF
8,30 221713,3011,306,30
H
H
SETTING THE ACTUAL TIME AND DAY
WEEK
These steps can also be taken before all the
Adjust the actual time using the
6
Select the actual day of the week using the button
7
D (1 = Monday - 2 = Tuesday - 3 =
4 = Thursday - 5 = Friday - 6 = Saturday -
D
D
buttons H
Wednesday -
°C
20
17
5
S
OF THE
others.
Sunday).
7 =
OFF
=COMFORT MODE
=ECONOMI MODE
=ANTIGELO MODE
8
22,30
Using the red buttons, adjust
2
the COMFOR t mode
temperature. The display will
show the temperature setting
instead of the room
temperature.
Using the blue buttons, adjust
3
the ECONOMY mode
temperature. The display will
show the temperature setting
instead of the room
temperature.
Reset button. By holding this
down for a few seconds with the
tip of a tool, you can zero all
programming operations and
restore the standard program.
4
P
I
Make sure that the
switch I is low, on the
winter position
Make sure that the
5
switch P is low, on the
AUTO (automatic)
position
THE OTHER PROGRAMSIntellitherm C75
OFF - this keeps the system constantly off or with the antifreeze protection option enabled,
depending on the choice made at the time of installation (see previous page).
ALWAYS ECONOMY - this constantly maintains the economy mode temperature
selected by means of the blue buttons.
ALWAYS COMFORT - this constantly maintains the comfort mode temperature selected
by
means of the red buttons.
CUSTOMIZING THE (PROGRAMMING)Intellitherm C75
Programming the Intellitherm C75 is extremely straightforward. All you have to do is change the
color of the sectors on the ring that coincide with the schedules you require, i.e.
- red for the hours when you want the comfort mode temperature
- red and black for the hours when you want the economy mode temperature
- black for the hours when you want the system switched off.
To change the color of the sectors, simply follow the numbered steps below.
Move the switch S to the AUTO position
Place the switch P high, on the
2
PROG (programming)
position.
P
The display will indicate 00.00
hours and day 1.
The flashing cursor on the ring
will automatically come into
position on the first sector after
the 24 hours.
Move the flashing
3
cursor (forwards or
backwards) around the
Ring with the aid of the
The sector whose color
want to change will flash
ring corresponding time
and the
keys
you
on the
H
will appear on the display.
Press the buttons
4
to color the
sectors On the
ring.
Each time you press one of
three buttons, the sector
becomes colored and the
moves forward by half an
use:
-the red buttons for a red
-the blue buttons for a half red
and half black sector
-the black buttons for a
sector .
To move the cursor
without changing the
color of a sector, use the
buttons.
WILD CARD
With Intellitherm C75, you can temporarily cut
out the automatic program at any time, without
losing it, in order to obtain a given temperature
(comfort, economy, off) continuously for an
interval ranging from
Put the switch S on the AUTO position
1
Put the switch P on the AUTO position
2
Press the red or blue or black buttons to establish the
3
number of hours (shown on the display) during which time
FUNCTION
1 to 240
cursor
hour;
sector
black
the
hours.
5
6
you want to cut out the automatic program and
temporarily "force" the comfort or economy or off
mode. The ring on the display will turn the color
corresponding to the temperature you have selected.
1
S
C
After programming the times of day, press button D to
change the day and repeat the previous steps for all the
other days of the week. If the program for one day is also
suitable for the subsequent days, copy it by pressing the
button C (copy). The day moves on by one unit and the
previously-memorized schedule is copied onto the next
day.
After completing all the changes, bring the switch P into the
AUTO position.
S
P
D
P
Loading...