Fantech RE 10XLT User Manual

Installation Manual

fantech

RE(C) Series

Exterior Roof / Wall Centrifugal Fans

Item #: 405262

Rev Date: 2015-05-12

United States

10048 Industrial Blvd., Lenexa, KS, 66215
Tel.: [phone] • Fax: [phone]

Canada

50 Kanalflakt Way, Bouctouche, NB, E4S 3M5
Tel.: [phone] • Fax: [phone]

Fantech Inc. certies that the
RE(C) Series shown herein is
licensed to bear the AMCA
Seal. The ratings shown are
based on tests and procedures
performed in accordance with
AMCA Publication 211 and
AMCA Publication 311 and
comply with the requirements
of the AMCA Certied Ratings
Program.

2

Note Warning /

Information Technical

Important

note

1. The compactness and adaptability of Models RE(C) fans permit easy
installation. The straight-thru air flow fans are shipped fully
assembled and can be mounted at any angle. For various mounting
and ducting options. (see Typical Installations)

2. Because this unit has rotating parts, safety precautions should be
exercised during the installation, operation, and maintenance phase.

3. CAUTION: “For General Ventilation Use Only. Do Not Use To Exhaust
Hazardous Or Explosive Material and Vapors.”

4. Remove unit from package and inspect within 15 days after receipt.
If damaged, report damage to carrier. Do Not operate this unit with
visible damage to the blower or impeller assembly.

5. Ensure centrifugal impeller has free rotation. If impeller hits orifice,
check screws holding motor bracket. Adjustment can be made by
loosening motor bracket screws, then pull up on motor bracket while
tightening screws. Tighten all screws before operating unit.

Practical tip

information

WARNINGS

DO NOT CONNECT POWER SUPPLY until fan is completely installed. Make
sure electrical service to the fan is in the locked “OFF” position.

1. All units are suitable for use with solid-state speed control.

2. WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS – OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer. If

you have any questions, contact your manufacturer's
representative.

b. CAUTION: Before installation, servicing or cleaning unit, switch

power off at service panel and lock the service disconnecting
means to prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service panel.

c. Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,
including fire-rated construction.

WEAR HAND PROTECTION AND STAY CLEAR OF SHARP EDGES.

6. Screen guards must be installed when fan will be within reach of
personnel, within (7) feet of the working area, or when advisable for
safety.

d. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Association (NFPA), and the American Society of
Heating Refrigeration and Air Conditioning Engineers (ASHRAE),
and the local code authorities.

e. When cutting or drilling into wall and ceiling, do not damage

electrical wiring and other hidden utilities.

f. Ducted fans must always be vented to the outdoors.

g. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a
GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

h. NEVER place a switch where it can be reached from a tub or

shower.

3. WARNING! Check voltage at the fan to see if it corresponds to the
motor name plate.

fantech

Typical Installations

3

Wall mount

Pitched roof

LD Duct
Silencer

Flat roof mount with curb

RE(C) Fan

RE(C) Fan

Insulated
Flexible
Duct

Grill

Dimensions

X

2 3/

3 9/

Y

D

D

4

16

16

6 11/

2 1/

2 15/

16

2

16

3040 19 0.18

2700 87 0.80

2800 153 1.40

A

B

C

H

D

Model A B C D X Y Max RPM Max Watts Max Amps

RE(C) 54* 10 15/

RE(C) 6 13 15/

RE(C) 8XL 16 9/

RE(C) 10XL 20 13/

RE(C) 10XLT 20 13/

All demensions in inches.
"H" dimensions is 1 1/2 on model REC only
* Optional 4" reducer for dimension C

16

6 5 15 1/

16

6 1/

16

16

16

5 15/

11 1/

12 11/

4

16

2

16

2

6 15 1/

8 20 6 9/

10 20 3 3 3250 394 3.60

10 20 3 3 2950 531 4.86

2

fantech

4

Installation Instructions

Suitable sealing such as tar or similar material (not included) should be used to prevent leakage. To prepare for installation, determine the size and
type of ducting, if any, to be used. Make an opening in the roof just large enough to accommodate ducting and electrical supply.

Flat Base Mounting

1. Base may be mounted directly on deck beneath roof shingles or upper
edge of base plate may be slid underneath shingles.

2. Securely screw or bolt base plate to roof through the four corner
mounting points.

3. Through the opening, attach ductwork to fan inlet orice by using
Fantech FC clamps or duct tape.

4. Refer to wiring diagram in this guide to complete electrical
connections.

5. Once secured and wired, generously apply tar or other sealant
around edges of base to prevent leakage. Be sure to replace any lifted
shingles.

Wiring

Curb Mounting

1. Outside dimensions of anged curb should be approximately 3/8"
smaller than the outside dimensions of base. Flanged curbs are
available from Fantech.

2. Center curb around roof opening and securely attach to roof. It is
advisable to put a bead of sealant around the inside edge of curb.

3. Before mounting base on curb, place a layer of sealant along the top
edge of the curb.

4. Place unit on curb and securely attach with bolts or screws.

5. Through the opening, attach ductwork to fan inlet orice by using
Fantech FC clamps or duct tape.

6. Refer to wiring diagram in this guide to complete electrical
connections.

7. Once secured and wired, generously apply tar or other sealant
around edges of base to prevent leakage. Be sure to replace any lifted
shingles.

SPECIAL WIRING PRECAUTIONS:

All installation should be wired according to the following diagrams. Failure to comply will cause the motor to "hum" or not work.

All units are pre-wired, just bring incoming supply into marked ports on terminal strip.

1. Turn off power at service entrance before wiring this fan.

2. Read the fan data plate to determine the current draw. Check that available supply is suitable.

3. Remove top enclosure of fan and the wiring box lid. A 7/8" hole is provided for electrical service entry. Be certain to use proper connector type for
securing conduit or cable.

4. Connect electrical supply inside wiring terminal per diagram below.

5. Replace wiring box lid and top enclosure.

Maximum torque that can be applied to the terminal block screws is 0.79 Nm (7 lb-in).

With motor speed controller Without motor speed controller

Motor
Speed

Control

Black
120V Supply

White

Capacitor

Brown
Black

Blue

GreenGreen

Motor

Black

120V Supply

White

Capacitor

Brown
Black

Blue

GreenGreen

Motor

fantech

Warranty

Five (5) Year Warranty

This warranty supersedes all prior warranties

5

DURING ENTIRE WARRANTY PERIOD:

Fantech will repair or replace any part which has a factory defect in
workmanship or material. Product may need to be returned to the
Fantech factory, together with a copy of the bill of sale and identified
with RMA number.

FOR FACTORY RETURN YOU MUST:

• Have a Return Materials Authorization (RMA) number. This may be

obtained by calling Fantech either in the USA at 1.800.747.1762 or
in CANADA at 1.800.565.3548. Please have bill of sale available.

• The RMA number must be clearly written on the outside of the

carton, or the carton will be refused.

• All parts and/or product will be repaired/replaced and shipped back to

buyer; no credit will be issued.

OR

The Distributor may place an order for the warranty part and/or product
and is invoiced. The Distributor will receive a credit equal to the invoice
only after product is returned prepaid and verified to be defective.

FANTECH WARRANTY TERMS DO NOT PROVIDE FOR REPLACEMENT
WITHOUT CHARGE PRIOR TO INSPECTION FOR A DEFECT.
REPLACEMENTS ISSUED IN ADVANCE OF DEFECT INSPECTION ARE
INVOICED, AND CREDIT IS PENDING INSPECTION OF RETURNED
MATERIAL. DEFECTIVE MATERIAL RETURNED BY END USERS SHOULD
NOT BE REPLACED BY THE DISTRIBUTOR WITHOUT CHARGE TO THE

END USER, AS CREDIT TO DISTRIBUTOR’S ACCOUNT WILL BE
PENDING INSPECTION AND VERIFICATION OF ACTUAL DEFECT BY
FANTECH.

THE FOLLOWING WARRANTIES DO NOT APPLY:

• Damages from shipping, either concealed or visible. Claim must be

filed with freight company.

• Damages resulting from improper wiring or installation.

• Damages or failure caused by acts of God, or resulting from improper

consumer procedures, such as:

1. Improper maintenance

2. Misuse, abuse, abnormal use, or accident, and

3. Incorrect electrical voltage or current.

• Removal or any alteration made on the Fantech label control number

or date of manufacture.

• Any other warranty, expressed, implied or written, and to any

consequential or incidental damages, loss or property, revenues, or
profit, or costs of removal, installation or reinstallation, for any breach
of warranty.

WARRANTY VALIDATION

• The user must keep a copy of the bill of sale to verify purchase date.

• These warranties give you specific legal rights, and are subject to an

applicable consumer protection legislation. You may have additional
rights which vary from state to state.

Limitation of Warranty and Liability

This warranty does not apply to any Fantech product or part which has
failed as a result of faulty installation or abuse, incorrect electrical
connections or alterations made by others, or use under abnormal
operating conditions or misapplication of the product or parts. We will
not approve for payment any repair not made by us or our authorized
agent without prior written consent. The foregoing shall constitute our
sole and exclusive warranty and our sole exclusive liability, and is in lieu
of any other warranties, whether written, oral, implied or statutory.
There are no warranties which extend beyond the description on the
page hereof. In no event, whether as a result of breach of contract, or

Warning

Fantech products are designed and manufactured to provide reliable
performance, but they are not guaranteed to be 100% free from
defects. Even reliable products will experience occasional failures and
this possibility should be recognized by the user. If these products are

warranty or alleged negligence, defect incorrect advice or other causes,
shall Fantech be liable for special or consequential damages, including,
but not limited to, loss of profits or revenue, loss of use of equipment or
any other associated equipment, cost of capital, cost of substitute
equipment, facilities or services, downtime costs, or claims of
customers of purchase for such damages. Fantech neither assumes or
authorizes any person to assume for it any other liability in connection
with the sale of product(s) or part(s). Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages so the
above limitations and exclusions may not apply to you.

used in a life support ventilation system where failure could result in loss
or injury, the user should provide adequate backup ventilation,
supplementary natural ventilation, failure alarm system, or acknowledge
willingness to accept the risk of such loss or injury.

fantech

6

Notes

fantech

Notes

7

fantech

fantech

Fantech reserves the right to make technical changes.
For updated documentation please refer to www.fantech.net

Fantech®