Fantasea EyeDaptor S90, EyeDaptor S95, EyeDaptor F67, RedEye S90, RedEye S95 Instruction Manual
...
1
Canon S90 & S95 Lens Accessories Instruction Manual 2011017
Fantasea Canon S90 & S95 Lens Accessories
(Cat. No. 4710, 5139, 5305, 5307)
Instruction Manual
1. Introduction
BigEye Lens S90/S95 (Cat. No. 5139) – A patented wide angle lens for Canon S90 and S95 housings.
Perfect for shooting seascapes, divers, ship wrecks and schools of fish, without moving further away
from the subject, thereby still taking full advantage of water clarity and artificial light sources.
EyeDaptor S90/S95-F67 (Cat. No. 4710) – Enables mounting 67mm threaded accessory lenses and filters
on Canon S90 and S95 housings. Especially designed to allow mounting the SharpEye Macro Lens M67
(Cat. No. 5128) on Canon S90 and S95 housings lens ports, which is perfect for shooting close-up images
of fish, corals, textures and more. The macro lens magnifies the subject and enables the camera to focus
on short distances for creating super sharp images.
RedEye Filter S90/S95 (Cat. No. 5305) – Red color correction filter for Canon S90 and S95 housings. Used
to restore the red color absorbed by blue water and allows for producing vivid and colorful underwater
images and videos.
PinkEye Filter S90/S95 (Cat. No. 5307) - Pink (magenta) color correction filter for Canon S90 and S95
housings. Used to restore the pink color absorbed by green water and allows for producing vivid and
colorful underwater images and videos.
2. Compatibility
The EyeDaptor S90/S95-F67, BigEye Lens S90/S95, RedEye Filter S90/S95 and PinkEye Filter S90/S95 are
compatible with the Canon S90 Housing (WP-DC35) and the Canon S95 Housing (WP-DC38).
3. Included in Packaging
Important Notice
This instruction manual relates to the EyeDaptor S90/S95-F67, BigEye Lens
S90/S95, RedEye Filter S90/S95 and PinkEye Filter S90/S95. Please refer to
corresponding paragraphs below for relevant instructions.
EyeDaptor S90/S95-F67
RedEye Filter S90/S95
PinkEye Filter S90/S95
BigEye Lens S90/S95
67mm Add-On Plate
EyeDaptor G Series
EyeDaptor G Series
BigEye Lens G Series
EyeDaptor G Series
EyeDaptor S90/S95-G Series
RedEye Insert
EyeDaptor S90/S95-G Series
PinkEye Insert
EyeDaptor S90/S95-G Series
EyeDaptor S90/S95-G Series
2
Canon S90 & S95 Lens Accessories Instruction Manual 2011017
4. Identification of Parts
5. Instructions for Use
1. Assembling the EyeDaptor S90/S95-F67
a. Place the EyeDaptor G Series on a flat and
protected surface, so that the adaptor
configuration is facing up and the flat side of the
adaptor is facing down (image #1).
b. Remove the 4 screws holding the 2 stoppers by
using the screwdriver included (image #2 on the
following page).
c. Turn the EyeDaptor G Series upside down and
remove the 2 stoppers off the adaptor (image #3
on the following page).
Important Notice
Please use the utmost care and do not use excessive force when assembling and
disassembling the different accessories, in order to not cause any damage to the
product.
EyeDaptor G Series
67mm Add-On Plate
PinkEye/RedEye Inserts
BigEye Lens G Series
EyeDaptor S90/S95-G Series
Image #1
3
Canon S90 & S95 Lens Accessories Instruction Manual 2011017
d. Remove the 2 stoppers off the EyeDaptor S90/S95-G Series as well, following the same method
described above for removing the stoppers off the EyeDaptor G Series.
e. Place the EyeDaptor G Series on a flat and protected surface, so that the adaptor configuration (the
side that attaches to the housing lens port) is facing up and the “TOP” marking is pointed away from
your body.
f. Hold the EyeDaptor S90/S95-G Series so that the two adaptor wings and the concaved part of the
adaptor are facing up and the adaptor niche is positioned at the bottom right (image #4).
g. Insert the EyeDaptor S90/S95-G Series into the dedicated groove of the EyeDaptor G Series. Note
that the two screw holes on the wings of the EyeDaptor S90/S95-G Series should be perfectly aligned
with the two small screw holes on the EyeDaptor G Series.
h. Insert the screws included into the dedicated screw holes on the two adaptor wings and use the
screwdriver included in order to tighten the screws into the EyeDaptor S90/S95-G Series and the
EyeDaptor G Series (image #5). Tighten the screws enough in order to keep the EyeDaptor S90/S95G Series fixed inside the EyeDaptor G Series, but don’t tighten them too strongly, as this might cause
damage to the products.
i. Replace the bungee cords originally attached to the EyeDaptor G Series with the 4 shorter bungee
cords included with the EyeDaptor S90/S95-G Series. First, remove the 4 bungee cords tied to the
EyeDaptor G Series by untying them and then pulling them out of the slot they were attached to.
Proceed by attaching the shorter bungee cords included with the EyeDaptor S90/S95-G Series to the
dedicated slots featured on the EyeDaptor G Series. Please note that there is no need to untie
shorter bungee cords in order to attach them to the EyeDaptor G Series. Simply insert the tied
Image #4
Image #5
Image #2
Image #3
Loading...