Fanimation CCK8002 Instruction Sheet

CCK8002
Close-To-Ceiling Kit

INSTRUCTION SHEET

USE THESE INSTRUCTION IN CONJUNCTION WITH YOUR FANIMATION
FAN OWNERS MANUAL AND IN PLACE OF THE STEPS FOR HOW TO
HANG YOUR CEILING FAN. IF YOU NO LONGER HAVE YOUR MANUAL,
ONE CAN BE DOWNLOADED AT WWW.FANIMATION.COM.

Safety Instructions

To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.1.
All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan must 2.
be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.
The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. Consult a qualified electrician if in doubt.3.
The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.4.
Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical knowledge or 5.
experience, have your fan installed by licensed electrician.

6˝ downrod 4.5˝ downrod Tall close-to-ceiling kit Short close-to-ceiling kit

After removing your kit from the packaging, use slight 1.
pressure to push down and remove the screw trim
cover ring from the ceiling canopy assembly. (Figure 1)

Separate the ceiling bracket from the ceiling canopy 2.
by loosening the two canopy-to-bracket screws where
the canopy is slotted and completely remove the other
two screws where it is not slotted and set aside for
later. (Figure 2)

Twist the ceiling bracket counter-clockwise and lift out 3.
of the ceiling canopy. There is another short canopy
option when it is needed to very close to ceiling.
(Figure 3)

CEILING CANOPY

REMOVE
SCREW

SLOTTED

SCREW TRIM
COVER RING

Figure 1

LOOSEN SCREWS (2)
BUT DO NOT REMOVE

REMOVE
SCREW

Figure 2

CEILING BRACKET

CEILING CANOPY

Figure 3

Short Canopy

1

On your fan’s motor, remove the two downrod support 4.
set screws and nuts from the downrod support and
discard. (Figure 4)

NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM

DOWNROD SUPPORT

Figure 4

Remove the three motor coupling screws from 5.
your fan and save for next step. (Figure 5)

Route your fan wires through the ceiling canopy and 6.
place ceiling canopy onto your motor. (Figure 6)

NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM

MOTOR

NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM

METAL SPACER

Figure 5

CEILING
CANOPY

SCREW TRIM
COVER RING

Alight the 3 big slots in the canopy to the 3 screws in7.
the motor coupler. Firmly attach the canopy cover to
the motor with the three screws removed in step 5
and steel washers from the part bag. (Figure 7)

WARNING

To avoid possible fire or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 8)

NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM

DOWNROD

SUPPORT

Figure 6

Figure 7

Figure 8

MOTOR

CEILING
CANOPY

SCREW TRIM
COVER RING

MOTOR

MAIN FUSE
BOX

2

Using the two screws and washers, securely attach 8.
the ceiling bracket to the ceiling junction box, making
sure to run the supply wires through the hole in the
center of the bracket. (Figure 9)

9. Loop the safety cable through pin hole in motor coupler
and put the cable clamp in the end of safety cable.
(Figure 10).

NOTE: SUPPLY WIRES
HAVE BEEN OMITTED
FROM DIAGRAM

WASHER

SCREW

CABLE CLAMP

OUTLET
BOX

MOUNTING
BRACKET

Figure 9

10. Loop the safety cable end through one of the holes in
the hanger plate up into the outlet box, then back out
the center of the plate, then connect the end with the
screw down clamp. Tighten the set screw in the clamp
. (Figure 11).

Lift your fan motor assembly and hang it from the 11.
ceiling bracket hook through one of the two screw
holes in the canopy lip. Do not use the grooved slots.
(Figure 12)

Connect your fan’s wiring according to your fan’s owners 12.
manual. If you have misplaced your owners manual
one can be downloaded at www.fanimation.com or
contact a licensed electrician to complete the wiring
of your fan.

MOUNTING
BRACKET

Figure 10

CABLE CLAMP

Figure 11

OUTLET
BOX

HOOK

Figure 12

3

Lift the fan off the bracket hook and mount your fan by 13.
sliding the ceiling canopy over the mounting bracket
with the two loosened screws going into the slots in
the canopy. Be sure all wiring is tucked into the ceiling
canopy and is not pinched. Once the canopy is flush
with your ceiling, turn clockwise to seat the screws
into the keyed portion of the slot. Tighten the screws.
(Figure 13)

Install the remaining two screws 14. removed in step 2
to secure the ceiling canopy to the ceiling bracket.
(Figure14)

NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM

SCREW

SLOT

SCREW

MOUNTING
BRACKET

SLOT

Figure 13

Push the screw cover trim ring up to conceal the 15.
screws, such that the mounting tabs seat into the
dimpled grooves in the ceiling canopy midway between
the screws. (Figure 15)

Reference your owners manual for any additional
assembly steps required for your Fanimation ceiling
fan.

Figure 14

MOUNTING

TAB (4)

.etelpmoc si tik gniliec-ot-esolc ruoy fo noitallatsnI16.

DIMPLED
GROOVE

SCREW TRIM
COVER RING

Figure 15

Copyright 2011 Fanimation 2011/07 V.02

Visit Our Website @ www.fanimation.com

10983 Bennett Parkway

Zionsville, IN 46077

Toll Free [phone]

FAX [phone]

Outside U.S. call [phone]